2 * (C) Copyright 2007-2008
3 * Stelian Pop <stelian@popies.net>
4 * Lead Tech Design <www.leadtechdesign.com>
6 * SPDX-License-Identifier: GPL-2.0+
11 #include <asm/arch/at91_common.h>
12 #include <asm/arch/clk.h>
13 #include <asm/arch/gpio.h>
16 * if CONFIG_AT91_GPIO_PULLUP ist set, keep pullups on on all
17 * peripheral pins. Good to have if hardware is soldered optionally
18 * or in case of SPI no slave is selected. Avoid lines to float
19 * needlessly. Use a short local PUP define.
21 * Due to errata "TXD floats when CTS is inactive" pullups are always
24 #ifdef CONFIG_AT91_GPIO_PULLUP
25 # define PUP CONFIG_AT91_GPIO_PULLUP
30 void at91_serial0_hw_init(void)
32 at91_set_a_periph(AT91_PIO_PORTA, 6, 1); /* TXD0 */
33 at91_set_a_periph(AT91_PIO_PORTA, 7, PUP); /* RXD0 */
34 at91_periph_clk_enable(ATMEL_ID_USART0);
37 void at91_serial1_hw_init(void)
39 at91_set_a_periph(AT91_PIO_PORTA, 11, 1); /* TXD1 */
40 at91_set_a_periph(AT91_PIO_PORTA, 12, PUP); /* RXD1 */
41 at91_periph_clk_enable(ATMEL_ID_USART1);
44 void at91_serial2_hw_init(void)
46 at91_set_a_periph(AT91_PIO_PORTA, 13, 1); /* TXD2 */
47 at91_set_a_periph(AT91_PIO_PORTA, 14, PUP); /* RXD2 */
48 at91_periph_clk_enable(ATMEL_ID_USART2);
51 void at91_seriald_hw_init(void)
53 at91_set_a_periph(AT91_PIO_PORTA, 21, PUP); /* DRXD */
54 at91_set_a_periph(AT91_PIO_PORTA, 22, 1); /* DTXD */
55 at91_periph_clk_enable(ATMEL_ID_SYS);
58 #if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)
59 void at91_spi0_hw_init(unsigned long cs_mask)
61 at91_set_a_periph(AT91_PIO_PORTA, 25, PUP); /* SPI0_MISO */
62 at91_set_a_periph(AT91_PIO_PORTA, 26, PUP); /* SPI0_MOSI */
63 at91_set_a_periph(AT91_PIO_PORTA, 27, PUP); /* SPI0_SPCK */
65 at91_periph_clk_enable(ATMEL_ID_SPI);
67 if (cs_mask & (1 << 0)) {
68 at91_set_a_periph(AT91_PIO_PORTA, 28, 1);
70 if (cs_mask & (1 << 1)) {
71 at91_set_b_periph(AT91_PIO_PORTB, 7, 1);
73 if (cs_mask & (1 << 2)) {
74 at91_set_a_periph(AT91_PIO_PORTD, 8, 1);
76 if (cs_mask & (1 << 3)) {
77 at91_set_b_periph(AT91_PIO_PORTD, 9, 1);
79 if (cs_mask & (1 << 4)) {
80 at91_set_pio_output(AT91_PIO_PORTA, 28, 1);
82 if (cs_mask & (1 << 5)) {
83 at91_set_pio_output(AT91_PIO_PORTB, 7, 1);
85 if (cs_mask & (1 << 6)) {
86 at91_set_pio_output(AT91_PIO_PORTD, 8, 1);
88 if (cs_mask & (1 << 7)) {
89 at91_set_pio_output(AT91_PIO_PORTD, 9, 1);
94 #ifdef CONFIG_GENERIC_ATMEL_MCI
95 void at91_mci_hw_init(void)
97 at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* MCI CLK */
98 at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* MCI CDA */
99 at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* MCI DA0 */
100 at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* MCI DA1 */
101 at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* MCI DA2 */
102 at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* MCI DA3 */
104 at91_periph_clk_enable(ATMEL_ID_MCI);