6 config ARCH_UNIPHIER_32BIT
10 config ARCH_UNIPHIER_64BIT
13 select SPL_SEPARATE_BSS
16 prompt "UniPhier SoC select"
17 default ARCH_UNIPHIER_PRO4
19 config ARCH_UNIPHIER_SLD3
20 bool "UniPhier PH1-sLD3 SoC"
21 select ARCH_UNIPHIER_32BIT
23 config ARCH_UNIPHIER_LD4_SLD8
24 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
25 select ARCH_UNIPHIER_32BIT
27 config ARCH_UNIPHIER_PRO4
28 bool "UniPhier PH1-Pro4 SoC"
29 select ARCH_UNIPHIER_32BIT
31 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
32 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
33 select ARCH_UNIPHIER_32BIT
35 config ARCH_UNIPHIER_LD11
36 bool "UniPhier PH1-LD11 SoC"
37 select ARCH_UNIPHIER_64BIT
39 config ARCH_UNIPHIER_LD20
40 bool "UniPhier PH1-LD20 SoC"
41 select ARCH_UNIPHIER_64BIT
45 config ARCH_UNIPHIER_LD4
46 bool "Enable UniPhier PH1-LD4 SoC support"
47 depends on ARCH_UNIPHIER_LD4_SLD8
50 config ARCH_UNIPHIER_SLD8
51 bool "Enable UniPhier PH1-sLD8 SoC support"
52 depends on ARCH_UNIPHIER_LD4_SLD8
55 config ARCH_UNIPHIER_PRO5
56 bool "Enable UniPhier PH1-Pro5 SoC support"
57 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
60 config ARCH_UNIPHIER_PXS2
61 bool "Enable UniPhier ProXstream2 SoC support"
62 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
65 config ARCH_UNIPHIER_LD6B
66 bool "Enable UniPhier PH1-LD6b SoC support"
67 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
70 config MICRO_SUPPORT_CARD
71 bool "Use Micro Support Card"
73 This option provides support for the expansion board, available
74 on some UniPhier reference boards.
76 Say Y to use the on-board UART, Ether, LED devices.
79 bool "Enable boot mode pins monitor command"
82 The command "pinmon" shows the state of the boot mode pins.
83 The boot mode pins are latched when the system reset is deasserted
84 and determine which device the system should load a boot image from.
86 config CMD_DDRPHY_DUMP
87 bool "Enable dump command of DDR PHY parameters"
88 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
91 The command "ddrphy" shows the resulting parameters of DDR PHY
92 training; it is useful for the evaluation of DDR PHY training.
94 config CMD_DDRMPHY_DUMP
95 bool "Enable dump command of DDR Multi PHY parameters"
96 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
99 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
100 training; it is useful for the evaluation of DDR Multi PHY training.