6 config ARCH_UNIPHIER_32BIT
9 select CPU_V7_HAS_NONSEC
11 select ARCH_SUPPORT_PSCI
15 prompt "UniPhier SoC select"
16 default ARCH_UNIPHIER_PRO4
18 config ARCH_UNIPHIER_LD4_SLD8
19 bool "UniPhier LD4/sLD8 SoCs"
20 select ARCH_UNIPHIER_32BIT
22 config ARCH_UNIPHIER_PRO4
23 bool "UniPhier Pro4 SoC"
24 select ARCH_UNIPHIER_32BIT
26 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
27 bool "UniPhier Pro5/PXs2/LD6b SoCs"
28 select ARCH_UNIPHIER_32BIT
30 config ARCH_UNIPHIER_V8_MULTI
31 bool "UniPhier V8 SoCs"
38 config ARCH_UNIPHIER_LD4
39 bool "Enable UniPhier LD4 SoC support"
40 depends on ARCH_UNIPHIER_LD4_SLD8
43 config ARCH_UNIPHIER_SLD8
44 bool "Enable UniPhier sLD8 SoC support"
45 depends on ARCH_UNIPHIER_LD4_SLD8
48 config ARCH_UNIPHIER_PRO5
49 bool "Enable UniPhier Pro5 SoC support"
50 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
53 config ARCH_UNIPHIER_PXS2
54 bool "Enable UniPhier Pxs2 SoC support"
55 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
58 config ARCH_UNIPHIER_LD6B
59 bool "Enable UniPhier LD6b SoC support"
60 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
63 config ARCH_UNIPHIER_LD11
64 bool "Enable UniPhier LD11 SoC support"
65 depends on ARCH_UNIPHIER_V8_MULTI
68 config ARCH_UNIPHIER_LD20
69 bool "Enable UniPhier LD20 SoC support"
70 depends on ARCH_UNIPHIER_V8_MULTI
74 config ARCH_UNIPHIER_PXS3
75 bool "Enable UniPhier PXs3 SoC support"
76 depends on ARCH_UNIPHIER_V8_MULTI
80 bool "Enable the UniPhier L2 cache controller"
81 depends on ARCH_UNIPHIER_32BIT
82 select SYS_CACHE_SHIFT_7
85 This option allows to use the UniPhier System Cache as L2 cache.
87 config MICRO_SUPPORT_CARD
88 bool "Use Micro Support Card"
90 This option provides support for the expansion board, available
91 on some UniPhier reference boards.
93 Say Y to use the on-board UART, Ether, LED devices.
96 bool "Enable boot mode pins monitor command"
99 The command "pinmon" shows the state of the boot mode pins.
100 The boot mode pins are latched when the system reset is deasserted
101 and determine which device the system should load a boot image from.
103 config CMD_DDRPHY_DUMP
104 bool "Enable dump command of DDR PHY parameters"
105 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \
106 ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11
109 The command "ddrphy" shows the resulting parameters of DDR PHY
110 training; it is useful for the evaluation of DDR PHY training.
112 config CMD_DDRMPHY_DUMP
113 bool "Enable dump command of DDR Multi PHY parameters"
114 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
117 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
118 training; it is useful for the evaluation of DDR Multi PHY training.