3 config SPL_LIBCOMMON_SUPPORT
9 config ARCH_UNIPHIER_32BIT
12 select CPU_V7_HAS_NONSEC
14 select ARCH_SUPPORT_PSCI
16 config ARCH_UNIPHIER_64BIT
19 select SPL_SEPARATE_BSS
20 select ARMV8_MULTIENTRY
21 select ARMV8_SPIN_TABLE
24 prompt "UniPhier SoC select"
25 default ARCH_UNIPHIER_PRO4
27 config ARCH_UNIPHIER_SLD3
28 bool "UniPhier PH1-sLD3 SoC"
29 select ARCH_UNIPHIER_32BIT
31 config ARCH_UNIPHIER_LD4_SLD8
32 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
33 select ARCH_UNIPHIER_32BIT
35 config ARCH_UNIPHIER_PRO4
36 bool "UniPhier PH1-Pro4 SoC"
37 select ARCH_UNIPHIER_32BIT
39 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
40 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
41 select ARCH_UNIPHIER_32BIT
43 config ARCH_UNIPHIER_LD11
44 bool "UniPhier PH1-LD11 SoC"
45 select ARCH_UNIPHIER_64BIT
47 config ARCH_UNIPHIER_LD20
48 bool "UniPhier PH1-LD20 SoC"
49 select ARCH_UNIPHIER_64BIT
54 config ARCH_UNIPHIER_LD4
55 bool "Enable UniPhier PH1-LD4 SoC support"
56 depends on ARCH_UNIPHIER_LD4_SLD8
59 config ARCH_UNIPHIER_SLD8
60 bool "Enable UniPhier PH1-sLD8 SoC support"
61 depends on ARCH_UNIPHIER_LD4_SLD8
64 config ARCH_UNIPHIER_PRO5
65 bool "Enable UniPhier PH1-Pro5 SoC support"
66 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
69 config ARCH_UNIPHIER_PXS2
70 bool "Enable UniPhier ProXstream2 SoC support"
71 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
74 config ARCH_UNIPHIER_LD6B
75 bool "Enable UniPhier PH1-LD6b SoC support"
76 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
80 bool "Enable the UniPhier L2 cache controller"
81 depends on ARCH_UNIPHIER_32BIT
82 select SYS_CACHE_SHIFT_7
85 This option allows to use the UniPhier System Cache as L2 cache.
87 config MICRO_SUPPORT_CARD
88 bool "Use Micro Support Card"
90 This option provides support for the expansion board, available
91 on some UniPhier reference boards.
93 Say Y to use the on-board UART, Ether, LED devices.
96 bool "Enable boot mode pins monitor command"
99 The command "pinmon" shows the state of the boot mode pins.
100 The boot mode pins are latched when the system reset is deasserted
101 and determine which device the system should load a boot image from.
103 config CMD_DDRPHY_DUMP
104 bool "Enable dump command of DDR PHY parameters"
105 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
108 The command "ddrphy" shows the resulting parameters of DDR PHY
109 training; it is useful for the evaluation of DDR PHY training.
111 config CMD_DDRMPHY_DUMP
112 bool "Enable dump command of DDR Multi PHY parameters"
113 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
116 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
117 training; it is useful for the evaluation of DDR Multi PHY training.