6 config ARCH_UNIPHIER_32BIT
9 select CPU_V7_HAS_NONSEC
11 select ARCH_SUPPORT_PSCI
14 prompt "UniPhier SoC select"
15 default ARCH_UNIPHIER_PRO4
17 config ARCH_UNIPHIER_LD4_SLD8
18 bool "UniPhier LD4/sLD8 SoCs"
19 select ARCH_UNIPHIER_32BIT
21 config ARCH_UNIPHIER_PRO4
22 bool "UniPhier Pro4 SoC"
23 select ARCH_UNIPHIER_32BIT
25 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
26 bool "UniPhier Pro5/PXs2/LD6b SoCs"
27 select ARCH_UNIPHIER_32BIT
29 config ARCH_UNIPHIER_V8_MULTI
30 bool "UniPhier V8 SoCs"
37 config ARCH_UNIPHIER_LD4
38 bool "Enable UniPhier LD4 SoC support"
39 depends on ARCH_UNIPHIER_LD4_SLD8
42 config ARCH_UNIPHIER_SLD8
43 bool "Enable UniPhier sLD8 SoC support"
44 depends on ARCH_UNIPHIER_LD4_SLD8
47 config ARCH_UNIPHIER_PRO5
48 bool "Enable UniPhier Pro5 SoC support"
49 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
52 config ARCH_UNIPHIER_PXS2
53 bool "Enable UniPhier Pxs2 SoC support"
54 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
57 config ARCH_UNIPHIER_LD6B
58 bool "Enable UniPhier LD6b SoC support"
59 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
62 config ARCH_UNIPHIER_LD11
63 bool "Enable UniPhier LD11 SoC support"
64 depends on ARCH_UNIPHIER_V8_MULTI
67 config ARCH_UNIPHIER_LD20
68 bool "Enable UniPhier LD20 SoC support"
69 depends on ARCH_UNIPHIER_V8_MULTI
73 config ARCH_UNIPHIER_PXS3
74 bool "Enable UniPhier PXs3 SoC support"
75 depends on ARCH_UNIPHIER_V8_MULTI
79 bool "Enable the UniPhier L2 cache controller"
80 depends on ARCH_UNIPHIER_32BIT
81 select SYS_CACHE_SHIFT_7
84 This option allows to use the UniPhier System Cache as L2 cache.
86 config MICRO_SUPPORT_CARD
87 bool "Use Micro Support Card"
89 This option provides support for the expansion board, available
90 on some UniPhier reference boards.
92 Say Y to use the on-board UART, Ether, LED devices.
95 bool "Enable boot mode pins monitor command"
98 The command "pinmon" shows the state of the boot mode pins.
99 The boot mode pins are latched when the system reset is deasserted
100 and determine which device the system should load a boot image from.
102 config CMD_DDRPHY_DUMP
103 bool "Enable dump command of DDR PHY parameters"
104 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \
105 ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11
108 The command "ddrphy" shows the resulting parameters of DDR PHY
109 training; it is useful for the evaluation of DDR PHY training.
111 config CMD_DDRMPHY_DUMP
112 bool "Enable dump command of DDR Multi PHY parameters"
113 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
116 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
117 training; it is useful for the evaluation of DDR Multi PHY training.