git.sur5r.net Git - u-boot/blob - board/freescale/mx6sxsabreauto/mx6sxsabreauto.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2014 Freescale Semiconductor, Inc.
   4  *
   5  * Author: Ye Li <ye.li@nxp.com>
   6  */
   7
   8 #include <asm/arch/clock.h>
   9 #include <asm/arch/crm_regs.h>
  10 #include <asm/arch/iomux.h>
  11 #include <asm/arch/imx-regs.h>
  12 #include <asm/arch/mx6-pins.h>
  13 #include <asm/arch/sys_proto.h>
  14 #include <asm/gpio.h>
  15 #include <asm/mach-imx/iomux-v3.h>
  16 #include <asm/mach-imx/boot_mode.h>
  17 #include <asm/io.h>
  18 #include <linux/sizes.h>
  19 #include <common.h>
  20 #include <fsl_esdhc.h>
  21 #include <miiphy.h>
  22 #include <netdev.h>
  23 #include <power/pmic.h>
  24 #include <power/pfuze100_pmic.h>
  25 #include "../common/pfuze.h"
  26 #include <usb.h>
  27 #include <usb/ehci-ci.h>
  28 #include <pca953x.h>
  29
  30 DECLARE_GLOBAL_DATA_PTR;
  31
  32 #define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
  33         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  34         PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  35
  36 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
  37         PAD_CTL_SPEED_HIGH   |                                   \
  38         PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
  39
  40 #define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
  41         PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
  42
  43 #define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
  44         PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
  45
  46 #define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
  47 #define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
  48                         PAD_CTL_SRE_FAST)
  49 #define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
  50
  51 int dram_init(void)
  52 {
  53         gd->ram_size = imx_ddr_size();
  54
  55         return 0;
  56 }
  57
  58 static iomux_v3_cfg_t const uart1_pads[] = {
  59         MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
  60         MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
  61 };
  62
  63 static iomux_v3_cfg_t const fec2_pads[] = {
  64         MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
  65         MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
  66         MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  67         MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  68         MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  69         MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  70         MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  71         MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  72         MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
  73         MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  74         MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  75         MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  76         MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  77         MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
  78 };
  79
  80 static void setup_iomux_uart(void)
  81 {
  82         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
  83 }
  84
  85 static int setup_fec(void)
  86 {
  87         struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
  88
  89         /* Use 125MHz anatop loopback REF_CLK1 for ENET2 */
  90         clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0);
  91
  92         return enable_fec_anatop_clock(1, ENET_125MHZ);
  93 }
  94
  95 int board_eth_init(bd_t *bis)
  96 {
  97         int ret;
  98
  99         imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
 100         setup_fec();
 101
 102         ret = fecmxc_initialize_multi(bis, 1,
 103                 CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
 104         if (ret)
 105                 printf("FEC%d MXC: %s:failed\n", 1, __func__);
 106
 107         return ret;
 108 }
 109
 110 int board_phy_config(struct phy_device *phydev)
 111 {
 112         /*
 113          * Enable 1.8V(SEL_1P5_1P8_POS_REG) on
 114          * Phy control debug reg 0
 115          */
 116         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
 117         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
 118
 119         /* rgmii tx clock delay enable */
 120         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
 121         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
 122
 123         if (phydev->drv->config)
 124                 phydev->drv->config(phydev);
 125
 126         return 0;
 127 }
 128
 129 int power_init_board(void)
 130 {
 131         struct udevice *dev;
 132         int ret;
 133         u32 dev_id, rev_id, i;
 134         u32 switch_num = 6;
 135         u32 offset = PFUZE100_SW1CMODE;
 136
 137         ret = pmic_get("pfuze100", &dev);
 138         if (ret == -ENODEV)
 139                 return 0;
 140
 141         if (ret != 0)
 142                 return ret;
 143
 144         dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
 145         rev_id = pmic_reg_read(dev, PFUZE100_REVID);
 146         printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
 147
 148
 149         /* Init mode to APS_PFM */
 150         pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM);
 151
 152         for (i = 0; i < switch_num - 1; i++)
 153                 pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM);
 154
 155         /* set SW1AB staby volatage 0.975V */
 156         pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b);
 157
 158         /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
 159         pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40);
 160
 161         /* set SW1C staby volatage 1.10V */
 162         pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x20);
 163
 164         /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
 165         pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40);
 166
 167         return 0;
 168 }
 169
 170 #ifdef CONFIG_USB_EHCI_MX6
 171 #define USB_OTHERREGS_OFFSET    0x800
 172 #define UCTRL_PWR_POL           (1 << 9)
 173
 174 static iomux_v3_cfg_t const usb_otg_pads[] = {
 175         /* OGT1 */
 176         MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
 177         MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
 178         /* OTG2 */
 179         MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
 180 };
 181
 182 static void setup_usb(void)
 183 {
 184         imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
 185                                          ARRAY_SIZE(usb_otg_pads));
 186 }
 187
 188 int board_usb_phy_mode(int port)
 189 {
 190         if (port == 1)
 191                 return USB_INIT_HOST;
 192         else
 193                 return usb_phy_mode(port);
 194 }
 195
 196 int board_ehci_hcd_init(int port)
 197 {
 198         u32 *usbnc_usb_ctrl;
 199
 200         if (port > 1)
 201                 return -EINVAL;
 202
 203         usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
 204                                  port * 4);
 205
 206         /* Set Power polarity */
 207         setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
 208
 209         return 0;
 210 }
 211 #endif
 212
 213 int board_early_init_f(void)
 214 {
 215         setup_iomux_uart();
 216
 217         return 0;
 218 }
 219
 220 #ifdef CONFIG_FSL_QSPI
 221
 222 #define QSPI_PAD_CTRL1  \
 223         (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
 224          PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
 225
 226 static iomux_v3_cfg_t const quadspi_pads[] = {
 227         MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 228         MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 229         MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 230         MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 231         MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 232         MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 233         MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 234         MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 235         MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 236         MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 237         MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 238         MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 239 };
 240
 241 int board_qspi_init(void)
 242 {
 243         /* Set the iomux */
 244         imx_iomux_v3_setup_multiple_pads(quadspi_pads,
 245                                          ARRAY_SIZE(quadspi_pads));
 246
 247         /* Set the clock */
 248         enable_qspi_clk(0);
 249
 250         return 0;
 251 }
 252 #endif
 253
 254 #ifdef CONFIG_NAND_MXS
 255 iomux_v3_cfg_t gpmi_pads[] = {
 256         MX6_PAD_NAND_CLE__RAWNAND_CLE           | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 257         MX6_PAD_NAND_ALE__RAWNAND_ALE           | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 258         MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 259         MX6_PAD_NAND_READY_B__RAWNAND_READY_B   | MUX_PAD_CTRL(GPMI_PAD_CTRL0),
 260         MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B               | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 261         MX6_PAD_NAND_RE_B__RAWNAND_RE_B         | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 262         MX6_PAD_NAND_WE_B__RAWNAND_WE_B         | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 263         MX6_PAD_NAND_DATA00__RAWNAND_DATA00     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 264         MX6_PAD_NAND_DATA01__RAWNAND_DATA01     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 265         MX6_PAD_NAND_DATA02__RAWNAND_DATA02     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 266         MX6_PAD_NAND_DATA03__RAWNAND_DATA03     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 267         MX6_PAD_NAND_DATA04__RAWNAND_DATA04     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 268         MX6_PAD_NAND_DATA05__RAWNAND_DATA05     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 269         MX6_PAD_NAND_DATA06__RAWNAND_DATA06     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 270         MX6_PAD_NAND_DATA07__RAWNAND_DATA07     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 271 };
 272
 273 static void setup_gpmi_nand(void)
 274 {
 275         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 276
 277         /* config gpmi nand iomux */
 278         imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
 279
 280         setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) |
 281                         MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) |
 282                         MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3)));
 283
 284         /* enable apbh clock gating */
 285         setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
 286 }
 287 #endif
 288
 289 int board_init(void)
 290 {
 291         struct gpio_desc desc;
 292         int ret;
 293
 294         /* Address of boot parameters */
 295         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 296
 297         ret = dm_gpio_lookup_name("gpio@30_4", &desc);
 298         if (ret)
 299                 return ret;
 300
 301         ret = dm_gpio_request(&desc, "cpu_per_rst_b");
 302         if (ret)
 303                 return ret;
 304         /* Reset CPU_PER_RST_B signal for enet phy and PCIE */
 305         dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
 306         udelay(500);
 307         dm_gpio_set_value(&desc, 1);
 308
 309         ret = dm_gpio_lookup_name("gpio@32_2", &desc);
 310         if (ret)
 311                 return ret;
 312
 313         ret = dm_gpio_request(&desc, "steer_enet");
 314         if (ret)
 315                 return ret;
 316
 317         dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
 318         udelay(500);
 319         /* Set steering signal to L for selecting B0 */
 320         dm_gpio_set_value(&desc, 0);
 321
 322 #ifdef CONFIG_USB_EHCI_MX6
 323         setup_usb();
 324 #endif
 325
 326 #ifdef CONFIG_FSL_QSPI
 327         board_qspi_init();
 328 #endif
 329
 330 #ifdef CONFIG_NAND_MXS
 331         setup_gpmi_nand();
 332 #endif
 333
 334         return 0;
 335 }
 336
 337 #ifdef CONFIG_CMD_BMODE
 338 static const struct boot_mode board_boot_modes[] = {
 339         {"sda", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)},
 340         {"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
 341         {"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)},
 342         {"nand", MAKE_CFGVAL(0x82, 0x00, 0x00, 0x00)},
 343         {NULL,   0},
 344 };
 345 #endif
 346
 347 int board_late_init(void)
 348 {
 349 #ifdef CONFIG_CMD_BMODE
 350         add_board_boot_modes(board_boot_modes);
 351 #endif
 352
 353         return 0;
 354 }
 355
 356 int checkboard(void)
 357 {
 358         puts("Board: MX6SX SABRE AUTO\n");
 359
 360         return 0;
 361 }