git.sur5r.net Git - u-boot/blob - board/ti/am57xx/board.c

   1 /*
   2  * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com
   3  *
   4  * Author: Felipe Balbi <balbi@ti.com>
   5  *
   6  * Based on board/ti/dra7xx/evm.c
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #include <common.h>
  12 #include <palmas.h>
  13 #include <sata.h>
  14 #include <usb.h>
  15 #include <asm/omap_common.h>
  16 #include <asm/omap_sec_common.h>
  17 #include <asm/emif.h>
  18 #include <asm/gpio.h>
  19 #include <asm/arch/gpio.h>
  20 #include <asm/arch/clock.h>
  21 #include <asm/arch/dra7xx_iodelay.h>
  22 #include <asm/arch/sys_proto.h>
  23 #include <asm/arch/mmc_host_def.h>
  24 #include <asm/arch/sata.h>
  25 #include <asm/arch/gpio.h>
  26 #include <asm/arch/omap.h>
  27 #include <environment.h>
  28 #include <usb.h>
  29 #include <linux/usb/gadget.h>
  30 #include <dwc3-uboot.h>
  31 #include <dwc3-omap-uboot.h>
  32 #include <ti-usb-phy-uboot.h>
  33
  34 #include "../common/board_detect.h"
  35 #include "mux_data.h"
  36
  37 #define board_is_x15()          board_ti_is("BBRDX15_")
  38 #define board_is_am572x_evm()   board_ti_is("AM572PM_")
  39 #define board_is_am572x_idk()   board_ti_is("AM572IDK")
  40
  41 #ifdef CONFIG_DRIVER_TI_CPSW
  42 #include <cpsw.h>
  43 #endif
  44
  45 DECLARE_GLOBAL_DATA_PTR;
  46
  47 /* GPIO 7_11 */
  48 #define GPIO_DDR_VTT_EN 203
  49
  50 #define SYSINFO_BOARD_NAME_MAX_LEN      45
  51
  52 const struct omap_sysinfo sysinfo = {
  53         "Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n"
  54 };
  55
  56 static const struct dmm_lisa_map_regs beagle_x15_lisa_regs = {
  57         .dmm_lisa_map_3 = 0x80740300,
  58         .is_ma_present  = 0x1
  59 };
  60
  61 void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
  62 {
  63         *dmm_lisa_regs = &beagle_x15_lisa_regs;
  64 }
  65
  66 static const struct emif_regs beagle_x15_emif1_ddr3_532mhz_emif_regs = {
  67         .sdram_config_init              = 0x61851b32,
  68         .sdram_config                   = 0x61851b32,
  69         .sdram_config2                  = 0x08000000,
  70         .ref_ctrl                       = 0x000040F1,
  71         .ref_ctrl_final                 = 0x00001035,
  72         .sdram_tim1                     = 0xcccf36ab,
  73         .sdram_tim2                     = 0x308f7fda,
  74         .sdram_tim3                     = 0x409f88a8,
  75         .read_idle_ctrl                 = 0x00050000,
  76         .zq_config                      = 0x5007190b,
  77         .temp_alert_config              = 0x00000000,
  78         .emif_ddr_phy_ctlr_1_init       = 0x0024400b,
  79         .emif_ddr_phy_ctlr_1            = 0x0e24400b,
  80         .emif_ddr_ext_phy_ctrl_1        = 0x10040100,
  81         .emif_ddr_ext_phy_ctrl_2        = 0x00910091,
  82         .emif_ddr_ext_phy_ctrl_3        = 0x00950095,
  83         .emif_ddr_ext_phy_ctrl_4        = 0x009b009b,
  84         .emif_ddr_ext_phy_ctrl_5        = 0x009e009e,
  85         .emif_rd_wr_lvl_rmp_win         = 0x00000000,
  86         .emif_rd_wr_lvl_rmp_ctl         = 0x80000000,
  87         .emif_rd_wr_lvl_ctl             = 0x00000000,
  88         .emif_rd_wr_exec_thresh         = 0x00000305
  89 };
  90
  91 /* Ext phy ctrl regs 1-35 */
  92 static const u32 beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs[] = {
  93         0x10040100,
  94         0x00910091,
  95         0x00950095,
  96         0x009B009B,
  97         0x009E009E,
  98         0x00980098,
  99         0x00340034,
 100         0x00350035,
 101         0x00340034,
 102         0x00310031,
 103         0x00340034,
 104         0x007F007F,
 105         0x007F007F,
 106         0x007F007F,
 107         0x007F007F,
 108         0x007F007F,
 109         0x00480048,
 110         0x004A004A,
 111         0x00520052,
 112         0x00550055,
 113         0x00500050,
 114         0x00000000,
 115         0x00600020,
 116         0x40011080,
 117         0x08102040,
 118         0x0,
 119         0x0,
 120         0x0,
 121         0x0,
 122         0x0,
 123         0x0,
 124         0x0,
 125         0x0,
 126         0x0,
 127         0x0
 128 };
 129
 130 static const struct emif_regs beagle_x15_emif2_ddr3_532mhz_emif_regs = {
 131         .sdram_config_init              = 0x61851b32,
 132         .sdram_config                   = 0x61851b32,
 133         .sdram_config2                  = 0x08000000,
 134         .ref_ctrl                       = 0x000040F1,
 135         .ref_ctrl_final                 = 0x00001035,
 136         .sdram_tim1                     = 0xcccf36b3,
 137         .sdram_tim2                     = 0x308f7fda,
 138         .sdram_tim3                     = 0x407f88a8,
 139         .read_idle_ctrl                 = 0x00050000,
 140         .zq_config                      = 0x5007190b,
 141         .temp_alert_config              = 0x00000000,
 142         .emif_ddr_phy_ctlr_1_init       = 0x0024400b,
 143         .emif_ddr_phy_ctlr_1            = 0x0e24400b,
 144         .emif_ddr_ext_phy_ctrl_1        = 0x10040100,
 145         .emif_ddr_ext_phy_ctrl_2        = 0x00910091,
 146         .emif_ddr_ext_phy_ctrl_3        = 0x00950095,
 147         .emif_ddr_ext_phy_ctrl_4        = 0x009b009b,
 148         .emif_ddr_ext_phy_ctrl_5        = 0x009e009e,
 149         .emif_rd_wr_lvl_rmp_win         = 0x00000000,
 150         .emif_rd_wr_lvl_rmp_ctl         = 0x80000000,
 151         .emif_rd_wr_lvl_ctl             = 0x00000000,
 152         .emif_rd_wr_exec_thresh         = 0x00000305
 153 };
 154
 155 static const u32 beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs[] = {
 156         0x10040100,
 157         0x00910091,
 158         0x00950095,
 159         0x009B009B,
 160         0x009E009E,
 161         0x00980098,
 162         0x00340034,
 163         0x00350035,
 164         0x00340034,
 165         0x00310031,
 166         0x00340034,
 167         0x007F007F,
 168         0x007F007F,
 169         0x007F007F,
 170         0x007F007F,
 171         0x007F007F,
 172         0x00480048,
 173         0x004A004A,
 174         0x00520052,
 175         0x00550055,
 176         0x00500050,
 177         0x00000000,
 178         0x00600020,
 179         0x40011080,
 180         0x08102040,
 181         0x0,
 182         0x0,
 183         0x0,
 184         0x0,
 185         0x0,
 186         0x0,
 187         0x0,
 188         0x0,
 189         0x0,
 190         0x0
 191 };
 192
 193 void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
 194 {
 195         switch (emif_nr) {
 196         case 1:
 197                 *regs = &beagle_x15_emif1_ddr3_532mhz_emif_regs;
 198                 break;
 199         case 2:
 200                 *regs = &beagle_x15_emif2_ddr3_532mhz_emif_regs;
 201                 break;
 202         }
 203 }
 204
 205 void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size)
 206 {
 207         switch (emif_nr) {
 208         case 1:
 209                 *regs = beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs;
 210                 *size = ARRAY_SIZE(beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs);
 211                 break;
 212         case 2:
 213                 *regs = beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs;
 214                 *size = ARRAY_SIZE(beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs);
 215                 break;
 216         }
 217 }
 218
 219 struct vcores_data beagle_x15_volts = {
 220         .mpu.value              = VDD_MPU_DRA7,
 221         .mpu.efuse.reg          = STD_FUSE_OPP_VMIN_MPU,
 222         .mpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 223         .mpu.addr               = TPS659038_REG_ADDR_SMPS12,
 224         .mpu.pmic               = &tps659038,
 225         .mpu.abb_tx_done_mask   = OMAP_ABB_MPU_TXDONE_MASK,
 226
 227         .eve.value              = VDD_EVE_DRA7,
 228         .eve.efuse.reg          = STD_FUSE_OPP_VMIN_DSPEVE,
 229         .eve.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 230         .eve.addr               = TPS659038_REG_ADDR_SMPS45,
 231         .eve.pmic               = &tps659038,
 232         .eve.abb_tx_done_mask   = OMAP_ABB_EVE_TXDONE_MASK,
 233
 234         .gpu.value              = VDD_GPU_DRA7,
 235         .gpu.efuse.reg          = STD_FUSE_OPP_VMIN_GPU,
 236         .gpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 237         .gpu.addr               = TPS659038_REG_ADDR_SMPS45,
 238         .gpu.pmic               = &tps659038,
 239         .gpu.abb_tx_done_mask   = OMAP_ABB_GPU_TXDONE_MASK,
 240
 241         .core.value             = VDD_CORE_DRA7,
 242         .core.efuse.reg         = STD_FUSE_OPP_VMIN_CORE,
 243         .core.efuse.reg_bits    = DRA752_EFUSE_REGBITS,
 244         .core.addr              = TPS659038_REG_ADDR_SMPS6,
 245         .core.pmic              = &tps659038,
 246
 247         .iva.value              = VDD_IVA_DRA7,
 248         .iva.efuse.reg          = STD_FUSE_OPP_VMIN_IVA,
 249         .iva.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 250         .iva.addr               = TPS659038_REG_ADDR_SMPS45,
 251         .iva.pmic               = &tps659038,
 252         .iva.abb_tx_done_mask   = OMAP_ABB_IVA_TXDONE_MASK,
 253 };
 254
 255 struct vcores_data am572x_idk_volts = {
 256         .mpu.value              = VDD_MPU_DRA7,
 257         .mpu.efuse.reg          = STD_FUSE_OPP_VMIN_MPU,
 258         .mpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 259         .mpu.addr               = TPS659038_REG_ADDR_SMPS12,
 260         .mpu.pmic               = &tps659038,
 261         .mpu.abb_tx_done_mask   = OMAP_ABB_MPU_TXDONE_MASK,
 262
 263         .eve.value              = VDD_EVE_DRA7,
 264         .eve.efuse.reg          = STD_FUSE_OPP_VMIN_DSPEVE,
 265         .eve.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 266         .eve.addr               = TPS659038_REG_ADDR_SMPS45,
 267         .eve.pmic               = &tps659038,
 268         .eve.abb_tx_done_mask   = OMAP_ABB_EVE_TXDONE_MASK,
 269
 270         .gpu.value              = VDD_GPU_DRA7,
 271         .gpu.efuse.reg          = STD_FUSE_OPP_VMIN_GPU,
 272         .gpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 273         .gpu.addr               = TPS659038_REG_ADDR_SMPS6,
 274         .gpu.pmic               = &tps659038,
 275         .gpu.abb_tx_done_mask   = OMAP_ABB_GPU_TXDONE_MASK,
 276
 277         .core.value             = VDD_CORE_DRA7,
 278         .core.efuse.reg         = STD_FUSE_OPP_VMIN_CORE,
 279         .core.efuse.reg_bits    = DRA752_EFUSE_REGBITS,
 280         .core.addr              = TPS659038_REG_ADDR_SMPS7,
 281         .core.pmic              = &tps659038,
 282
 283         .iva.value              = VDD_IVA_DRA7,
 284         .iva.efuse.reg          = STD_FUSE_OPP_VMIN_IVA,
 285         .iva.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 286         .iva.addr               = TPS659038_REG_ADDR_SMPS8,
 287         .iva.pmic               = &tps659038,
 288         .iva.abb_tx_done_mask   = OMAP_ABB_IVA_TXDONE_MASK,
 289 };
 290
 291 #ifdef CONFIG_SPL_BUILD
 292 /* No env to setup for SPL */
 293 static inline void setup_board_eeprom_env(void) { }
 294
 295 /* Override function to read eeprom information */
 296 void do_board_detect(void)
 297 {
 298         int rc;
 299
 300         rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
 301                                   CONFIG_EEPROM_CHIP_ADDRESS);
 302         if (rc)
 303                 printf("ti_i2c_eeprom_init failed %d\n", rc);
 304 }
 305
 306 #else   /* CONFIG_SPL_BUILD */
 307
 308 /* Override function to read eeprom information: actual i2c read done by SPL*/
 309 void do_board_detect(void)
 310 {
 311         char *bname = NULL;
 312         int rc;
 313
 314         rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
 315                                   CONFIG_EEPROM_CHIP_ADDRESS);
 316         if (rc)
 317                 printf("ti_i2c_eeprom_init failed %d\n", rc);
 318
 319         if (board_is_x15())
 320                 bname = "BeagleBoard X15";
 321         else if (board_is_am572x_evm())
 322                 bname = "AM572x EVM";
 323         else if (board_is_am572x_idk())
 324                 bname = "AM572x IDK";
 325
 326         if (bname)
 327                 snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN,
 328                          "Board: %s REV %s\n", bname, board_ti_get_rev());
 329 }
 330
 331 static void setup_board_eeprom_env(void)
 332 {
 333         char *name = "beagle_x15";
 334         int rc;
 335
 336         rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
 337                                   CONFIG_EEPROM_CHIP_ADDRESS);
 338         if (rc)
 339                 goto invalid_eeprom;
 340
 341         if (board_is_x15())
 342                 name = "beagle_x15";
 343         else if (board_is_am572x_evm())
 344                 name = "am57xx_evm";
 345         else if (board_is_am572x_idk())
 346                 name = "am572x_idk";
 347         else
 348                 printf("Unidentified board claims %s in eeprom header\n",
 349                        board_ti_get_name());
 350
 351 invalid_eeprom:
 352         set_board_info_env(name);
 353 }
 354
 355 #endif  /* CONFIG_SPL_BUILD */
 356
 357 void vcores_init(void)
 358 {
 359         if (board_is_am572x_idk())
 360                 *omap_vcores = &am572x_idk_volts;
 361         else
 362                 *omap_vcores = &beagle_x15_volts;
 363 }
 364
 365 void hw_data_init(void)
 366 {
 367         *prcm = &dra7xx_prcm;
 368         *dplls_data = &dra7xx_dplls;
 369         *ctrl = &dra7xx_ctrl;
 370 }
 371
 372 int board_init(void)
 373 {
 374         gpmc_init();
 375         gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100);
 376
 377         return 0;
 378 }
 379
 380 int board_late_init(void)
 381 {
 382         setup_board_eeprom_env();
 383
 384         /*
 385          * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds
 386          * This is the POWERHOLD-in-Low behavior.
 387          */
 388         palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1);
 389
 390         /*
 391          * Default FIT boot on HS devices. Non FIT images are not allowed
 392          * on HS devices.
 393          */
 394         if (get_device_type() == HS_DEVICE)
 395                 setenv("boot_fit", "1");
 396
 397         return 0;
 398 }
 399
 400 void set_muxconf_regs(void)
 401 {
 402         do_set_mux32((*ctrl)->control_padconf_core_base,
 403                      early_padconf, ARRAY_SIZE(early_padconf));
 404 }
 405
 406 #ifdef CONFIG_IODELAY_RECALIBRATION
 407 void recalibrate_iodelay(void)
 408 {
 409         const struct pad_conf_entry *pconf;
 410         const struct iodelay_cfg_entry *iod;
 411         int pconf_sz, iod_sz;
 412
 413         if (board_is_am572x_idk()) {
 414                 pconf = core_padconf_array_essential_am572x_idk;
 415                 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am572x_idk);
 416                 iod = iodelay_cfg_array_am572x_idk;
 417                 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am572x_idk);
 418         } else {
 419                 /* Common for X15/GPEVM */
 420                 pconf = core_padconf_array_essential_x15;
 421                 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_x15);
 422                 iod = iodelay_cfg_array_x15;
 423                 iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15);
 424         }
 425
 426         __recalibrate_iodelay(pconf, pconf_sz, iod, iod_sz);
 427 }
 428 #endif
 429
 430 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
 431 int board_mmc_init(bd_t *bis)
 432 {
 433         omap_mmc_init(0, 0, 0, -1, -1);
 434         omap_mmc_init(1, 0, 0, -1, -1);
 435         return 0;
 436 }
 437 #endif
 438
 439 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT)
 440 int spl_start_uboot(void)
 441 {
 442         /* break into full u-boot on 'c' */
 443         if (serial_tstc() && serial_getc() == 'c')
 444                 return 1;
 445
 446 #ifdef CONFIG_SPL_ENV_SUPPORT
 447         env_init();
 448         env_relocate_spec();
 449         if (getenv_yesno("boot_os") != 1)
 450                 return 1;
 451 #endif
 452
 453         return 0;
 454 }
 455 #endif
 456
 457 #ifdef CONFIG_USB_DWC3
 458 static struct dwc3_device usb_otg_ss2 = {
 459         .maximum_speed = USB_SPEED_HIGH,
 460         .base = DRA7_USB_OTG_SS2_BASE,
 461         .tx_fifo_resize = false,
 462         .index = 1,
 463 };
 464
 465 static struct dwc3_omap_device usb_otg_ss2_glue = {
 466         .base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE,
 467         .utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
 468         .index = 1,
 469 };
 470
 471 static struct ti_usb_phy_device usb_phy2_device = {
 472         .usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER,
 473         .index = 1,
 474 };
 475
 476 int usb_gadget_handle_interrupts(int index)
 477 {
 478         u32 status;
 479
 480         status = dwc3_omap_uboot_interrupt_status(index);
 481         if (status)
 482                 dwc3_uboot_handle_interrupt(index);
 483
 484         return 0;
 485 }
 486 #endif /* CONFIG_USB_DWC3 */
 487
 488 #if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP)
 489 int board_usb_init(int index, enum usb_init_type init)
 490 {
 491         enable_usb_clocks(index);
 492         switch (index) {
 493         case 0:
 494                 if (init == USB_INIT_DEVICE) {
 495                         printf("port %d can't be used as device\n", index);
 496                         disable_usb_clocks(index);
 497                         return -EINVAL;
 498                 }
 499                 break;
 500         case 1:
 501                 if (init == USB_INIT_DEVICE) {
 502 #ifdef CONFIG_USB_DWC3
 503                         usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL;
 504                         usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
 505                         ti_usb_phy_uboot_init(&usb_phy2_device);
 506                         dwc3_omap_uboot_init(&usb_otg_ss2_glue);
 507                         dwc3_uboot_init(&usb_otg_ss2);
 508 #endif
 509                 } else {
 510                         printf("port %d can't be used as host\n", index);
 511                         disable_usb_clocks(index);
 512                         return -EINVAL;
 513                 }
 514
 515                 break;
 516         default:
 517                 printf("Invalid Controller Index\n");
 518         }
 519
 520         return 0;
 521 }
 522
 523 int board_usb_cleanup(int index, enum usb_init_type init)
 524 {
 525 #ifdef CONFIG_USB_DWC3
 526         switch (index) {
 527         case 0:
 528         case 1:
 529                 if (init == USB_INIT_DEVICE) {
 530                         ti_usb_phy_uboot_exit(index);
 531                         dwc3_uboot_exit(index);
 532                         dwc3_omap_uboot_exit(index);
 533                 }
 534                 break;
 535         default:
 536                 printf("Invalid Controller Index\n");
 537         }
 538 #endif
 539         disable_usb_clocks(index);
 540         return 0;
 541 }
 542 #endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */
 543
 544 #ifdef CONFIG_DRIVER_TI_CPSW
 545
 546 /* Delay value to add to calibrated value */
 547 #define RGMII0_TXCTL_DLY_VAL            ((0x3 << 5) + 0x8)
 548 #define RGMII0_TXD0_DLY_VAL             ((0x3 << 5) + 0x8)
 549 #define RGMII0_TXD1_DLY_VAL             ((0x3 << 5) + 0x2)
 550 #define RGMII0_TXD2_DLY_VAL             ((0x4 << 5) + 0x0)
 551 #define RGMII0_TXD3_DLY_VAL             ((0x4 << 5) + 0x0)
 552 #define VIN2A_D13_DLY_VAL               ((0x3 << 5) + 0x8)
 553 #define VIN2A_D17_DLY_VAL               ((0x3 << 5) + 0x8)
 554 #define VIN2A_D16_DLY_VAL               ((0x3 << 5) + 0x2)
 555 #define VIN2A_D15_DLY_VAL               ((0x4 << 5) + 0x0)
 556 #define VIN2A_D14_DLY_VAL               ((0x4 << 5) + 0x0)
 557
 558 static void cpsw_control(int enabled)
 559 {
 560         /* VTP can be added here */
 561 }
 562
 563 static struct cpsw_slave_data cpsw_slaves[] = {
 564         {
 565                 .slave_reg_ofs  = 0x208,
 566                 .sliver_reg_ofs = 0xd80,
 567                 .phy_addr       = 1,
 568         },
 569         {
 570                 .slave_reg_ofs  = 0x308,
 571                 .sliver_reg_ofs = 0xdc0,
 572                 .phy_addr       = 2,
 573         },
 574 };
 575
 576 static struct cpsw_platform_data cpsw_data = {
 577         .mdio_base              = CPSW_MDIO_BASE,
 578         .cpsw_base              = CPSW_BASE,
 579         .mdio_div               = 0xff,
 580         .channels               = 8,
 581         .cpdma_reg_ofs          = 0x800,
 582         .slaves                 = 1,
 583         .slave_data             = cpsw_slaves,
 584         .ale_reg_ofs            = 0xd00,
 585         .ale_entries            = 1024,
 586         .host_port_reg_ofs      = 0x108,
 587         .hw_stats_reg_ofs       = 0x900,
 588         .bd_ram_ofs             = 0x2000,
 589         .mac_control            = (1 << 5),
 590         .control                = cpsw_control,
 591         .host_port_num          = 0,
 592         .version                = CPSW_CTRL_VERSION_2,
 593 };
 594
 595 static u64 mac_to_u64(u8 mac[6])
 596 {
 597         int i;
 598         u64 addr = 0;
 599
 600         for (i = 0; i < 6; i++) {
 601                 addr <<= 8;
 602                 addr |= mac[i];
 603         }
 604
 605         return addr;
 606 }
 607
 608 static void u64_to_mac(u64 addr, u8 mac[6])
 609 {
 610         mac[5] = addr;
 611         mac[4] = addr >> 8;
 612         mac[3] = addr >> 16;
 613         mac[2] = addr >> 24;
 614         mac[1] = addr >> 32;
 615         mac[0] = addr >> 40;
 616 }
 617
 618 int board_eth_init(bd_t *bis)
 619 {
 620         int ret;
 621         uint8_t mac_addr[6];
 622         uint32_t mac_hi, mac_lo;
 623         uint32_t ctrl_val;
 624         int i;
 625         u64 mac1, mac2;
 626         u8 mac_addr1[6], mac_addr2[6];
 627         int num_macs;
 628
 629         /* try reading mac address from efuse */
 630         mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
 631         mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
 632         mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
 633         mac_addr[1] = (mac_hi & 0xFF00) >> 8;
 634         mac_addr[2] = mac_hi & 0xFF;
 635         mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
 636         mac_addr[4] = (mac_lo & 0xFF00) >> 8;
 637         mac_addr[5] = mac_lo & 0xFF;
 638
 639         if (!getenv("ethaddr")) {
 640                 printf("<ethaddr> not set. Validating first E-fuse MAC\n");
 641
 642                 if (is_valid_ethaddr(mac_addr))
 643                         eth_setenv_enetaddr("ethaddr", mac_addr);
 644         }
 645
 646         mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
 647         mac_hi = readl((*ctrl)->control_core_mac_id_1_hi);
 648         mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
 649         mac_addr[1] = (mac_hi & 0xFF00) >> 8;
 650         mac_addr[2] = mac_hi & 0xFF;
 651         mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
 652         mac_addr[4] = (mac_lo & 0xFF00) >> 8;
 653         mac_addr[5] = mac_lo & 0xFF;
 654
 655         if (!getenv("eth1addr")) {
 656                 if (is_valid_ethaddr(mac_addr))
 657                         eth_setenv_enetaddr("eth1addr", mac_addr);
 658         }
 659
 660         ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
 661         ctrl_val |= 0x22;
 662         writel(ctrl_val, (*ctrl)->control_core_control_io1);
 663
 664         /* The phy address for the AM572x IDK are different than x15 */
 665         if (board_is_am572x_idk()) {
 666                 cpsw_data.slave_data[0].phy_addr = 0;
 667                 cpsw_data.slave_data[1].phy_addr = 1;
 668         }
 669
 670         ret = cpsw_register(&cpsw_data);
 671         if (ret < 0)
 672                 printf("Error %d registering CPSW switch\n", ret);
 673
 674         /*
 675          * Export any Ethernet MAC addresses from EEPROM.
 676          * On AM57xx the 2 MAC addresses define the address range
 677          */
 678         board_ti_get_eth_mac_addr(0, mac_addr1);
 679         board_ti_get_eth_mac_addr(1, mac_addr2);
 680
 681         if (is_valid_ethaddr(mac_addr1) && is_valid_ethaddr(mac_addr2)) {
 682                 mac1 = mac_to_u64(mac_addr1);
 683                 mac2 = mac_to_u64(mac_addr2);
 684
 685                 /* must contain an address range */
 686                 num_macs = mac2 - mac1 + 1;
 687                 /* <= 50 to protect against user programming error */
 688                 if (num_macs > 0 && num_macs <= 50) {
 689                         for (i = 0; i < num_macs; i++) {
 690                                 u64_to_mac(mac1 + i, mac_addr);
 691                                 if (is_valid_ethaddr(mac_addr)) {
 692                                         eth_setenv_enetaddr_by_index("eth",
 693                                                                      i + 2,
 694                                                                      mac_addr);
 695                                 }
 696                         }
 697                 }
 698         }
 699
 700         return ret;
 701 }
 702 #endif
 703
 704 #ifdef CONFIG_BOARD_EARLY_INIT_F
 705 /* VTT regulator enable */
 706 static inline void vtt_regulator_enable(void)
 707 {
 708         if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL)
 709                 return;
 710
 711         gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
 712         gpio_direction_output(GPIO_DDR_VTT_EN, 1);
 713 }
 714
 715 int board_early_init_f(void)
 716 {
 717         vtt_regulator_enable();
 718         return 0;
 719 }
 720 #endif
 721
 722 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
 723 int ft_board_setup(void *blob, bd_t *bd)
 724 {
 725         ft_cpu_setup(blob, bd);
 726
 727         return 0;
 728 }
 729 #endif
 730
 731 #ifdef CONFIG_SPL_LOAD_FIT
 732 int board_fit_config_name_match(const char *name)
 733 {
 734         if (board_is_x15() && !strcmp(name, "am57xx-beagle-x15"))
 735                 return 0;
 736         else if (board_is_am572x_evm() && !strcmp(name, "am57xx-beagle-x15"))
 737                 return 0;
 738         else if (board_is_am572x_idk() && !strcmp(name, "am572x-idk"))
 739                 return 0;
 740         else
 741                 return -1;
 742 }
 743 #endif
 744
 745 #ifdef CONFIG_TI_SECURE_DEVICE
 746 void board_fit_image_post_process(void **p_image, size_t *p_size)
 747 {
 748         secure_boot_verify_image(p_image, p_size);
 749 }
 750
 751 void board_tee_image_process(ulong tee_image, size_t tee_size)
 752 {
 753         secure_tee_install((u32)tee_image);
 754 }
 755
 756 U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process);
 757 #endif