1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
5 bool "Enable Driver Model for Ethernet drivers"
8 Enable driver model for Ethernet.
10 The eth_*() interface will be implemented by the UC_ETH class
11 This is currently implemented in net/eth.c
12 Look in include/net.h for details.
15 bool "TI Common Platform Ethernet Switch"
18 This driver supports the TI three port switch gigabit ethernet
19 subsystem found in the TI SoCs.
22 bool "Network device support"
26 You must select Y to enable any network device support
27 Generally if you have any networking support this is a given
34 bool "Enable GbE PHY status parsing and configuration"
36 Enables support for parsing the status output and for
37 configuring GbE PHYs (affects the inner workings of some
38 commands and miiphyutil.c).
41 bool "Atheros AG7xxx Ethernet MAC support"
42 depends on DM_ETH && ARCH_ATH79
45 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
46 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
50 bool "Altera Triple-Speed Ethernet MAC support"
54 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
55 Please find details on the "Triple-Speed Ethernet MegaCore Function
56 Resource Center" of Altera.
59 bool "Broadcom SF2 (Starfighter2) Ethernet support"
62 This is an abstract framework which provides a generic interface
63 to MAC and DMA management for multiple Broadcom SoCs such as
64 Cygnus, NSP and bcm28155_ap platforms.
66 config BCM_SF2_ETH_DEFAULT_PORT
67 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
68 depends on BCM_SF2_ETH
71 Default port number for the Starfighter2 ethernet driver.
73 config BCM_SF2_ETH_GMAC
74 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
75 depends on BCM_SF2_ETH
77 This flag enables the ethernet support for Broadcom platforms with
78 GMAC such as Cygnus. This driver is based on the framework provided
79 by the BCM_SF2_ETH driver.
80 Say Y to any bcmcygnus based platforms.
83 bool "Synopsys DWC Ethernet QOS device support"
87 This driver supports the Synopsys Designware Ethernet QOS (Quality
88 Of Service) IP block. The IP supports many options for bus type,
89 clocking/reset structure, and feature list. This driver currently
90 supports the specific configuration used in NVIDIA's Tegra186 chip,
91 but should be extensible to other combinations quite easily.
94 bool "Intel PRO/1000 Gigabit Ethernet support"
96 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
97 adapters. For more information on how to identify your adapter, go
98 to the Adapter & Driver ID Guide at:
100 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
102 config E1000_SPI_GENERIC
103 bool "Allow access to the Intel 8257x SPI bus"
106 Allow generic access to the SPI bus on the Intel 8257x, for
107 example with the "sspi" command.
110 bool "Enable SPI bus utility code"
113 Utility code for direct access to the SPI bus on Intel 8257x.
114 This does not do anything useful unless you set at least one
115 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
118 bool "Enable the e1000 command"
121 This enables the 'e1000' management command for E1000 devices. When
122 used on devices with SPI support you can reprogram the EEPROM from
126 depends on DM_ETH && SANDBOX
128 bool "Sandbox: Mocked Ethernet driver"
130 This driver simply responds with fake ARP replies and ping
131 replies that are used to verify network stack functionality
133 This driver is particularly useful in the test/dm/eth.c tests
135 config ETH_SANDBOX_RAW
136 depends on DM_ETH && SANDBOX
138 bool "Sandbox: Bridge to Linux Raw Sockets"
140 This driver is a bridge from the bottom of the network stack
141 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
142 network traffic to be tested from within sandbox. See
143 board/sandbox/README.sandbox for more details.
145 config ETH_DESIGNWARE
146 bool "Synopsys Designware Ethernet MAC"
149 This MAC is present in SoCs from various vendors. It supports
150 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
151 provide the PHY (physical media interface).
154 bool "OpenCores 10/100 Mbps Ethernet MAC"
156 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
158 config FEC_MXC_SHARE_MDIO
159 bool "Share the MDIO bus for FEC controller"
162 config FEC_MXC_MDIO_BASE
163 hex "MDIO base address for the FEC controller"
164 depends on FEC_MXC_SHARE_MDIO
166 This specifies the MDIO registers base address. It is used when
167 two FEC controllers share MDIO bus.
170 bool "FEC Ethernet controller"
171 depends on MX5 || MX6 || MX7
173 This driver supports the 10/100 Fast Ethernet controller for
177 bool "Ftmac100 Ethernet Support"
179 This MAC is present in Andestech SoCs.
182 bool "Marvell Orion5x/Kirkwood network interface support"
183 depends on KIRKWOOD || ORION5X
185 This driver supports the network interface units in the
186 Marvell Orion5x and Kirkwood SoCs
189 bool "Marvell Armada XP/385/3700 network interface support"
190 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
193 This driver supports the network interface units in the
194 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
197 bool "Marvell Armada 375/7K/8K network interface support"
198 depends on ARMADA_375 || ARMADA_8K
201 This driver supports the network interface units in the
202 Marvell ARMADA 375, 7K and 8K SoCs.
205 bool "Cadence MACB/GEM Ethernet Interface"
209 The Cadence MACB ethernet interface is found on many Atmel
210 AT91 and SAMA5 parts. This driver also supports the Cadence
211 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
212 Say Y to include support for the MACB/GEM chip.
215 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
218 The Cadence MACB ethernet interface was used on Zynq platform.
219 Say Y to enable support for the MACB/GEM in Zynq chip.
222 bool "Intel Platform Controller Hub EG20T GMAC driver"
223 depends on DM_ETH && DM_PCI
226 This MAC is present in Intel Platform Controller Hub EG20T. It
227 supports 10/100/1000 Mbps operation.
232 Enable the support of the Reduced Gigabit Media-Independent
236 bool "Realtek 8139 series Ethernet controller driver"
238 This driver supports Realtek 8139 series fast ethernet family of
239 PCI chipsets/adapters.
242 bool "Realtek 8169 series Ethernet controller driver"
244 This driver supports Realtek 8169 series gigabit ethernet family of
245 PCI/PCIe chipsets/adapters.
248 bool "SMSC LAN911x and LAN921x controller driver"
253 hex "SMC911X Base Address"
255 Define this to hold the physical address
256 of the device (I/O space)
259 prompt "SMC911X bus width"
260 default SMC911X_16_BIT
262 config SMC911X_32_BIT
263 bool "Enable 32-bit interface"
265 config SMC911X_16_BIT
266 bool "Enable 16-bit interface"
268 Define this if data bus is 16 bits. If your processor
269 automatically converts one 32 bit word to two 16 bit
270 words you may also try CONFIG_SMC911X_32_BIT.
276 bool "Enable Allwinner GMAC Ethernet support"
278 Enable the support for Sun7i GMAC Ethernet controller
280 config SUN7I_GMAC_FORCE_TXERR
281 bool "Force PA17 as gmac function"
282 depends on SUN7I_GMAC
284 Some ethernet phys needs TXERR control. Since the GMAC
285 doesn't have such signal, setting PA17 as GMAC function
286 makes the pin output low, which enables data transmission.
289 bool "Allwinner Sun4i Ethernet MAC support"
293 This driver supports the Allwinner based SUN4I Ethernet MAC.
296 bool "Allwinner Sun8i Ethernet MAC support"
301 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
302 It can be found in H3/A64/A83T based SoCs and compatible with both
303 External and Internal PHYs.
306 bool "Renesas SH Ethernet MAC"
309 This driver supports the Ethernet for Renesas SH and ARM SoCs.
311 config XILINX_AXIEMAC
312 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
315 bool "Xilinx AXI Ethernet"
317 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
319 config XILINX_EMACLITE
320 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
323 bool "Xilinx Ethernetlite"
325 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
328 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
330 bool "Xilinx Ethernet GEM"
332 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
335 bool "Microchip PIC32 Ethernet Support"
336 depends on DM_ETH && MACH_PIC32
339 This driver implements 10/100 Mbps Ethernet and MAC layer for
340 Microchip PIC32 microcontrollers.
343 bool "Rockchip Synopsys Designware Ethernet MAC"
344 depends on DM_ETH && ETH_DESIGNWARE
346 This driver provides Rockchip SoCs network support based on the
347 Synopsys Designware driver.
350 bool "Renesas Ethernet AVB MAC"
351 depends on DM_ETH && RCAR_GEN3
354 This driver implements support for the Ethernet AVB block in
355 Renesas M3 and H3 SoCs.
358 bool "Fast Ethernet Controller on MPC8XX"
362 This driver implements support for the Fast Ethernet Controller
367 depends on MPC8XX_FEC
372 depends on ETHER_ON_FEC1
375 Define to the hardcoded PHY address which corresponds
376 to the given FEC; i. e.
377 #define CONFIG_FEC1_PHY 4
378 means that the PHY with address 4 is connected to FEC1
380 When set to -1, means to probe for first available.
384 depends on ETHER_ON_FEC1
387 The PHY does not have a RXERR line (RMII only).
388 (so program the FEC to ignore it).
392 depends on MPC8XX_FEC && MPC885
397 depends on ETHER_ON_FEC2
400 Define to the hardcoded PHY address which corresponds
401 to the given FEC; i. e.
402 #define CONFIG_FEC1_PHY 4
403 means that the PHY with address 4 is connected to FEC1
405 When set to -1, means to probe for first available.
407 config FEC2_PHY_NORXERR
409 depends on ETHER_ON_FEC2
412 The PHY does not have a RXERR line (RMII only).
413 (so program the FEC to ignore it).
415 config SYS_DPAA_QBMAN
416 bool "Device tree fixup for QBMan on freescale SOCs"
417 depends on (ARM || PPC) && !SPL_BUILD
418 default y if ARCH_B4860 || \
437 QBman fixups to allow deep sleep in DPAA 1 SOCs
441 bool "Enable Three-Speed Ethernet Controller"
443 This driver implements support for the (Enhanced) Three-Speed
444 Ethernet Controller found on Freescale SoCs.