2 * Copyright 2013-2015 Arcturus Networks, Inc.
3 * http://www.arcturusnetworks.com/products/ucp1020/
4 * based on include/configs/p1_p2_rdb_pc.h
5 * original copyright follows:
6 * Copyright 2009-2011 Freescale Semiconductor, Inc.
8 * SPDX-License-Identifier: GPL-2.0+
12 * QorIQ uCP1020-xx boards configuration file
17 #define CONFIG_FSL_ELBC
18 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
19 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
20 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
21 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
22 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
23 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
25 #if defined(CONFIG_TARTGET_UCP1020T1)
27 #define CONFIG_UCP1020_REV_1_3
29 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
31 #define CONFIG_TSEC_ENET
34 #define CONFIG_HAS_ETH0
35 #define CONFIG_HAS_ETH1
36 #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF
37 #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE
38 #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD
39 #define CONFIG_IPADDR 10.80.41.229
40 #define CONFIG_SERVERIP 10.80.41.227
41 #define CONFIG_NETMASK 255.255.252.0
42 #define CONFIG_ETHPRIME "eTSEC3"
44 #ifndef CONFIG_SPI_FLASH
46 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
49 #define CONFIG_SYS_L2_SIZE (256 << 10)
51 #define CONFIG_LAST_STAGE_INIT
55 #if defined(CONFIG_TARGET_UCP1020)
57 #define CONFIG_UCP1020
58 #define CONFIG_UCP1020_REV_1_3
60 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
62 #define CONFIG_TSEC_ENET
66 #define CONFIG_HAS_ETH0
67 #define CONFIG_HAS_ETH1
68 #define CONFIG_HAS_ETH2
69 #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF
70 #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE
71 #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD
72 #define CONFIG_IPADDR 192.168.1.81
73 #define CONFIG_IPADDR1 192.168.1.82
74 #define CONFIG_IPADDR2 192.168.1.83
75 #define CONFIG_SERVERIP 192.168.1.80
76 #define CONFIG_GATEWAYIP 102.168.1.1
77 #define CONFIG_NETMASK 255.255.255.0
78 #define CONFIG_ETHPRIME "eTSEC1"
80 #ifndef CONFIG_SPI_FLASH
82 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
85 #define CONFIG_SYS_L2_SIZE (256 << 10)
87 #define CONFIG_LAST_STAGE_INIT
92 #define CONFIG_RAMBOOT_SDCARD
93 #define CONFIG_SYS_RAMBOOT
94 #define CONFIG_SYS_EXTRA_ENV_RELOC
95 #define CONFIG_SYS_TEXT_BASE 0x11000000
96 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
99 #ifdef CONFIG_SPIFLASH
100 #define CONFIG_RAMBOOT_SPIFLASH
101 #define CONFIG_SYS_RAMBOOT
102 #define CONFIG_SYS_EXTRA_ENV_RELOC
103 #define CONFIG_SYS_TEXT_BASE 0x11000000
104 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
107 #ifndef CONFIG_SYS_TEXT_BASE
108 #define CONFIG_SYS_TEXT_BASE 0xeff80000
110 #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000
112 #ifndef CONFIG_RESET_VECTOR_ADDRESS
113 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
116 #ifndef CONFIG_SYS_MONITOR_BASE
117 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
120 /* High Level Configuration Options */
123 /* #define CONFIG_MPC85xx */
127 #define CONFIG_ENV_OVERWRITE
129 #define CONFIG_CMD_SATA
130 #define CONFIG_SATA_SIL
131 #define CONFIG_SYS_SATA_MAX_DEVICE 2
132 #define CONFIG_LIBATA
135 #define CONFIG_SYS_CLK_FREQ 66666666
136 #define CONFIG_DDR_CLK_FREQ 66666666
138 #define CONFIG_HWCONFIG
140 #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
141 #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
142 #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */
144 * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
145 * there will be one entry in this array for each two (dummy) sensors in
146 * CONFIG_DTT_SENSORS.
148 * For uCP1020 module:
149 * - only one ADM1021/NCT72
151 * - conversion rate 0x02 = 0.25 conversions/second
152 * - ALERT output disabled
153 * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
154 * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
156 #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
157 0x02, 0, 1, 0, 85, 1, 0, 85} }
159 #define CONFIG_CMD_DTT
162 * These can be toggled for performance analysis, otherwise use default.
164 #define CONFIG_L2_CACHE
167 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
169 #define CONFIG_ENABLE_36BIT_PHYS
171 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
172 #define CONFIG_SYS_MEMTEST_END 0x1fffffff
173 #define CONFIG_PANIC_HANG /* do not reset board on panic */
175 #define CONFIG_SYS_CCSRBAR 0xffe00000
176 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
178 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
180 #ifdef CONFIG_SPL_BUILD
181 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
185 #define CONFIG_DDR_ECC_ENABLE
186 #define CONFIG_SYS_FSL_DDR3
187 #ifndef CONFIG_DDR_ECC_ENABLE
188 #define CONFIG_SYS_DDR_RAW_TIMING
189 #define CONFIG_DDR_SPD
191 #define CONFIG_SYS_SPD_BUS_NUM 1
192 #undef CONFIG_FSL_DDR_INTERACTIVE
194 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
195 #define CONFIG_CHIP_SELECTS_PER_CTRL 1
196 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
197 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
198 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
200 #define CONFIG_NUM_DDR_CONTROLLERS 1
201 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
203 /* Default settings for DDR3 */
204 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
205 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
206 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
207 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
208 #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
209 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
211 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
212 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
213 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
214 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
216 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
217 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608
218 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000
219 #define CONFIG_SYS_DDR_RCW_1 0x00000000
220 #define CONFIG_SYS_DDR_RCW_2 0x00000000
221 #ifdef CONFIG_DDR_ECC_ENABLE
222 #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */
224 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
226 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050
227 #define CONFIG_SYS_DDR_TIMING_4 0x00220001
228 #define CONFIG_SYS_DDR_TIMING_5 0x03402400
230 #define CONFIG_SYS_DDR_TIMING_3 0x00020000
231 #define CONFIG_SYS_DDR_TIMING_0 0x00330004
232 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846
233 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF
234 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
235 #define CONFIG_SYS_DDR_MODE_1 0x40461520
236 #define CONFIG_SYS_DDR_MODE_2 0x8000c000
237 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000
239 #undef CONFIG_CLOCKS_IN_MHZ
244 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
245 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2)
246 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
247 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable
249 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
250 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
251 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
255 * Local Bus Definitions
257 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
258 #define CONFIG_SYS_FLASH_BASE 0xec000000
260 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
262 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
265 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
267 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
268 #define CONFIG_SYS_FLASH_QUIET_TEST
269 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
271 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
273 #undef CONFIG_SYS_FLASH_CHECKSUM
274 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
275 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
277 #define CONFIG_FLASH_CFI_DRIVER
278 #define CONFIG_SYS_FLASH_CFI
279 #define CONFIG_SYS_FLASH_EMPTY_INFO
280 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
282 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
284 #define CONFIG_SYS_INIT_RAM_LOCK
285 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
286 /* Initial L1 address */
287 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
288 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
289 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
290 /* Size of used area in RAM */
291 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
293 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
294 GENERATED_GBL_DATA_SIZE)
295 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
297 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */
298 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
300 #define CONFIG_SYS_PMC_BASE 0xff980000
301 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
302 #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
304 #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
305 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
308 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
309 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
310 #ifdef CONFIG_NAND_FSL_ELBC
311 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
312 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
315 /* Serial Port - controlled on board with jumper J8
319 #define CONFIG_CONS_INDEX 1
320 #undef CONFIG_SERIAL_SOFTWARE_FIFO
321 #define CONFIG_SYS_NS16550_SERIAL
322 #define CONFIG_SYS_NS16550_REG_SIZE 1
323 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
324 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
325 #define CONFIG_NS16550_MIN_FUNCTIONS
328 #define CONFIG_SYS_BAUDRATE_TABLE \
329 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
331 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
332 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
335 #define CONFIG_SYS_I2C
336 #define CONFIG_SYS_I2C_FSL
337 #define CONFIG_SYS_FSL_I2C_SPEED 400000
338 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
339 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
340 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
341 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
342 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
343 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
344 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
346 #define CONFIG_RTC_DS1337
347 #define CONFIG_SYS_RTC_DS1337_NOOSC
348 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
349 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
350 #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
351 #define CONFIG_SYS_I2C_IDT6V49205B 0x69
354 * eSPI - Enhanced SPI
356 #define CONFIG_HARD_SPI
358 #define CONFIG_SF_DEFAULT_SPEED 10000000
359 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
361 #if defined(CONFIG_PCI)
364 * Memory space is mapped 1-1, but I/O space must start from 0.
367 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
368 #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9"
369 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
370 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
371 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
372 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
373 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
374 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
375 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
376 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
378 /* controller 1, Slot 2, tgtid 1, Base address a000 */
379 #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10"
380 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
381 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
382 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
383 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
384 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
385 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
386 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
387 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
389 #define CONFIG_CMD_PCI
391 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
392 #define CONFIG_DOS_PARTITION
393 #endif /* CONFIG_PCI */
398 #ifdef CONFIG_ENV_FIT_UCBOOT
400 #define CONFIG_ENV_IS_IN_FLASH
401 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000)
402 #define CONFIG_ENV_SIZE 0x20000
403 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
407 #define CONFIG_ENV_SPI_BUS 0
408 #define CONFIG_ENV_SPI_CS 0
409 #define CONFIG_ENV_SPI_MAX_HZ 10000000
410 #define CONFIG_ENV_SPI_MODE 0
412 #ifdef CONFIG_RAMBOOT_SPIFLASH
414 #define CONFIG_ENV_IS_IN_SPI_FLASH
415 #define CONFIG_ENV_SIZE 0x3000 /* 12KB */
416 #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */
417 #define CONFIG_ENV_SECT_SIZE 0x1000
419 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
420 /* Address and size of Redundant Environment Sector */
421 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
422 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
425 #elif defined(CONFIG_RAMBOOT_SDCARD)
426 #define CONFIG_ENV_IS_IN_MMC
427 #define CONFIG_FSL_FIXED_MMC_LOCATION
428 #define CONFIG_ENV_SIZE 0x2000
429 #define CONFIG_SYS_MMC_ENV_DEV 0
431 #elif defined(CONFIG_SYS_RAMBOOT)
432 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
433 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
434 #define CONFIG_ENV_SIZE 0x2000
437 #define CONFIG_ENV_IS_IN_FLASH
438 #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE)
439 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
440 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
441 #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000)
442 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
443 /* Address and size of Redundant Environment Sector */
444 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
445 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
450 #endif /* CONFIG_ENV_FIT_UCBOOT */
452 #define CONFIG_LOADS_ECHO /* echo on for serial download */
453 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
456 * Command line configuration.
458 #define CONFIG_CMD_IRQ
459 #define CONFIG_CMD_DATE
460 #define CONFIG_CMD_IRQ
461 #define CONFIG_CMD_REGINFO
462 #define CONFIG_CMD_ERRATA
463 #define CONFIG_CMD_CRAMFS
468 #define CONFIG_HAS_FSL_DR_USB
470 #if defined(CONFIG_HAS_FSL_DR_USB)
471 #define CONFIG_USB_EHCI
473 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
475 #ifdef CONFIG_USB_EHCI
476 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
477 #define CONFIG_USB_EHCI_FSL
481 #undef CONFIG_WATCHDOG /* watchdog disabled */
484 #define CONFIG_FSL_ESDHC
485 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
486 #define CONFIG_MMC_SPI
487 #define CONFIG_CMD_MMC_SPI
488 #define CONFIG_GENERIC_MMC
491 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
492 #define CONFIG_DOS_PARTITION
495 /* Misc Extra Settings */
496 #undef CONFIG_WATCHDOG /* watchdog disabled */
499 * Miscellaneous configurable options
501 #define CONFIG_SYS_LONGHELP /* undef to save memory */
502 #define CONFIG_CMDLINE_EDITING /* Command-line editing */
503 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
504 #if defined(CONFIG_CMD_KGDB)
505 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
507 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
509 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
510 /* Print Buffer Size */
511 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
512 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
513 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
516 * For booting Linux, the board info and command line data
517 * have to be in the first 64 MB of memory, since this is
518 * the maximum mapped by the Linux kernel during initialization.
520 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
521 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
523 #if defined(CONFIG_CMD_KGDB)
524 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
525 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
529 * Environment Configuration
532 #if defined(CONFIG_TSEC_ENET)
534 #if defined(CONFIG_UCP1020_REV_1_2)
535 #define CONFIG_PHY_MICREL_KSZ9021
536 #elif defined(CONFIG_UCP1020_REV_1_3)
537 #define CONFIG_PHY_MICREL_KSZ9031
539 #error "UCP1020 module revision is not defined !!!"
542 #define CONFIG_BOOTP_SERVERIP
544 #define CONFIG_MII /* MII PHY management */
545 #define CONFIG_TSEC1_NAME "eTSEC1"
546 #define CONFIG_TSEC2_NAME "eTSEC2"
547 #define CONFIG_TSEC3_NAME "eTSEC3"
549 #define TSEC1_PHY_ADDR 4
550 #define TSEC2_PHY_ADDR 0
551 #define TSEC2_PHY_ADDR_SGMII 0x00
552 #define TSEC3_PHY_ADDR 6
554 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
555 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
556 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
558 #define TSEC1_PHYIDX 0
559 #define TSEC2_PHYIDX 0
560 #define TSEC3_PHYIDX 0
562 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
566 #define CONFIG_HOSTNAME UCP1020
567 #define CONFIG_ROOTPATH "/opt/nfsroot"
568 #define CONFIG_BOOTFILE "uImage"
569 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
571 /* default location for tftp and bootm */
572 #define CONFIG_LOADADDR 1000000
574 #define CONFIG_BOOTARGS /* the boot command will set bootargs */
576 #define CONFIG_BAUDRATE 115200
578 #if defined(CONFIG_DONGLE)
580 #define CONFIG_EXTRA_ENV_SETTINGS \
581 "bootcmd=run prog_spi_mbrbootcramfs\0" \
582 "bootfile=uImage\0" \
583 "consoledev=ttyS0\0" \
584 "cramfsfile=image.cramfs\0" \
585 "dtbaddr=0x00c00000\0" \
586 "dtbfile=image.dtb\0" \
587 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
588 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
589 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
590 "fileaddr=0x01000000\0" \
591 "filesize=0x00080000\0" \
592 "flashmbr=sf probe 0; " \
593 "tftp $loadaddr $mbr; " \
594 "sf erase $mbr_offset +$filesize; " \
595 "sf write $loadaddr $mbr_offset $filesize\0" \
596 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \
597 "protect off $nor_recoveryaddr +$filesize; " \
598 "erase $nor_recoveryaddr +$filesize; " \
599 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
600 "protect on $nor_recoveryaddr +$filesize\0 " \
601 "flashuboot=tftp $ubootaddr $ubootfile; " \
602 "protect off $nor_ubootaddr +$filesize; " \
603 "erase $nor_ubootaddr +$filesize; " \
604 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
605 "protect on $nor_ubootaddr +$filesize\0 " \
606 "flashworking=tftp $workingaddr $cramfsfile; " \
607 "protect off $nor_workingaddr +$filesize; " \
608 "erase $nor_workingaddr +$filesize; " \
609 "cp.b $workingaddr $nor_workingaddr $filesize; " \
610 "protect on $nor_workingaddr +$filesize\0 " \
611 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
612 "kerneladdr=0x01100000\0" \
613 "kernelfile=uImage\0" \
614 "loadaddr=0x01000000\0" \
615 "mbr=uCP1020d.mbr\0" \
616 "mbr_offset=0x00000000\0" \
617 "mmbr=uCP1020Quiet.mbr\0" \
619 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
621 "mmc write $loadaddr 1 1\0" \
622 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \
623 "mmc erase 0x40 0x400; " \
624 "mmc write $loadaddr 0x40 0x400\0" \
626 "nor_recoveryaddr=0xEC0A0000\0" \
627 "nor_ubootaddr=0xEFF80000\0" \
628 "nor_workingaddr=0xECFA0000\0" \
629 "norbootrecovery=setenv bootargs $recoverybootargs" \
630 " console=$consoledev,$baudrate $othbootargs; " \
631 "run norloadrecovery; " \
632 "bootm $kerneladdr - $dtbaddr\0" \
633 "norbootworking=setenv bootargs $workingbootargs" \
634 " console=$consoledev,$baudrate $othbootargs; " \
635 "run norloadworking; " \
636 "bootm $kerneladdr - $dtbaddr\0" \
637 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
638 "setenv cramfsaddr $nor_recoveryaddr; " \
639 "cramfsload $dtbaddr $dtbfile; " \
640 "cramfsload $kerneladdr $kernelfile\0" \
641 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
642 "setenv cramfsaddr $nor_workingaddr; " \
643 "cramfsload $dtbaddr $dtbfile; " \
644 "cramfsload $kerneladdr $kernelfile\0" \
645 "prog_spi_mbr=run spi__mbr\0" \
646 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \
647 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
648 "run spi__cramfs\0" \
649 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
650 " console=$consoledev,$baudrate $othbootargs; " \
651 "tftp $rootfsaddr $rootfsfile; " \
652 "tftp $loadaddr $kernelfile; " \
653 "tftp $dtbaddr $dtbfile; " \
654 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
655 "ramdisk_size=120000\0" \
656 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
657 "recoveryaddr=0x02F00000\0" \
658 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
659 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
660 "mw.l 0xffe0f008 0x00400000\0" \
661 "rootfsaddr=0x02F00000\0" \
662 "rootfsfile=rootfs.ext2.gz.uboot\0" \
663 "rootpath=/opt/nfsroot\0" \
664 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
665 "protect off 0xeC000000 +$filesize; " \
666 "erase 0xEC000000 +$filesize; " \
667 "cp.b $loadaddr 0xEC000000 $filesize; " \
668 "cmp.b $loadaddr 0xEC000000 $filesize; " \
669 "protect on 0xeC000000 +$filesize\0" \
670 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
671 "protect off 0xeFF80000 +$filesize; " \
672 "erase 0xEFF80000 +$filesize; " \
673 "cp.b $loadaddr 0xEFF80000 $filesize; " \
674 "cmp.b $loadaddr 0xEFF80000 $filesize; " \
675 "protect on 0xeFF80000 +$filesize\0" \
676 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \
677 "sf probe 0; sf erase 0x8000 +$filesize; " \
678 "sf write $loadaddr 0x8000 $filesize\0" \
679 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \
680 "protect off 0xec0a0000 +$filesize; " \
681 "erase 0xeC0A0000 +$filesize; " \
682 "cp.b $loadaddr 0xeC0A0000 $filesize; " \
683 "protect on 0xec0a0000 +$filesize\0" \
684 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
685 "sf probe 1; sf erase 0 +$filesize; " \
686 "sf write $loadaddr 0 $filesize\0" \
687 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
688 "sf probe 0; sf erase 0 +$filesize; " \
689 "sf write $loadaddr 0 $filesize\0" \
690 "tftpflash=tftpboot $loadaddr $uboot; " \
691 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
692 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
693 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
694 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
695 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
696 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
697 "ubootaddr=0x01000000\0" \
698 "ubootfile=u-boot.bin\0" \
699 "ubootd=u-boot4dongle.bin\0" \
700 "upgrade=run flashworking\0" \
701 "usb_phy_type=ulpi\0 " \
702 "workingaddr=0x02F00000\0" \
703 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
707 #if defined(CONFIG_UCP1020T1)
709 #define CONFIG_EXTRA_ENV_SETTINGS \
710 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
711 "bootfile=uImage\0" \
712 "consoledev=ttyS0\0" \
713 "cramfsfile=image.cramfs\0" \
714 "dtbaddr=0x00c00000\0" \
715 "dtbfile=image.dtb\0" \
716 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
717 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
718 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
719 "fileaddr=0x01000000\0" \
720 "filesize=0x00080000\0" \
721 "flashmbr=sf probe 0; " \
722 "tftp $loadaddr $mbr; " \
723 "sf erase $mbr_offset +$filesize; " \
724 "sf write $loadaddr $mbr_offset $filesize\0" \
725 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \
726 "protect off $nor_recoveryaddr +$filesize; " \
727 "erase $nor_recoveryaddr +$filesize; " \
728 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
729 "protect on $nor_recoveryaddr +$filesize\0 " \
730 "flashuboot=tftp $ubootaddr $ubootfile; " \
731 "protect off $nor_ubootaddr +$filesize; " \
732 "erase $nor_ubootaddr +$filesize; " \
733 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \
734 "protect on $nor_ubootaddr +$filesize\0 " \
735 "flashworking=tftp $workingaddr $cramfsfile; " \
736 "protect off $nor_workingaddr +$filesize; " \
737 "erase $nor_workingaddr +$filesize; " \
738 "cp.b $workingaddr $nor_workingaddr $filesize; " \
739 "protect on $nor_workingaddr +$filesize\0 " \
740 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
741 "kerneladdr=0x01100000\0" \
742 "kernelfile=uImage\0" \
743 "loadaddr=0x01000000\0" \
744 "mbr=uCP1020.mbr\0" \
745 "mbr_offset=0x00000000\0" \
747 "nor_recoveryaddr=0xEC0A0000\0" \
748 "nor_ubootaddr=0xEFF80000\0" \
749 "nor_workingaddr=0xECFA0000\0" \
750 "norbootrecovery=setenv bootargs $recoverybootargs" \
751 " console=$consoledev,$baudrate $othbootargs; " \
752 "run norloadrecovery; " \
753 "bootm $kerneladdr - $dtbaddr\0" \
754 "norbootworking=setenv bootargs $workingbootargs" \
755 " console=$consoledev,$baudrate $othbootargs; " \
756 "run norloadworking; " \
757 "bootm $kerneladdr - $dtbaddr\0" \
758 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
759 "setenv cramfsaddr $nor_recoveryaddr; " \
760 "cramfsload $dtbaddr $dtbfile; " \
761 "cramfsload $kerneladdr $kernelfile\0" \
762 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
763 "setenv cramfsaddr $nor_workingaddr; " \
764 "cramfsload $dtbaddr $dtbfile; " \
765 "cramfsload $kerneladdr $kernelfile\0" \
766 "othbootargs=quiet\0" \
767 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
768 " console=$consoledev,$baudrate $othbootargs; " \
769 "tftp $rootfsaddr $rootfsfile; " \
770 "tftp $loadaddr $kernelfile; " \
771 "tftp $dtbaddr $dtbfile; " \
772 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
773 "ramdisk_size=120000\0" \
774 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
775 "recoveryaddr=0x02F00000\0" \
776 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
777 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
778 "mw.l 0xffe0f008 0x00400000\0" \
779 "rootfsaddr=0x02F00000\0" \
780 "rootfsfile=rootfs.ext2.gz.uboot\0" \
781 "rootpath=/opt/nfsroot\0" \
783 "tftpflash=tftpboot $loadaddr $uboot; " \
784 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
785 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
786 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
787 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
788 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
789 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
790 "ubootaddr=0x01000000\0" \
791 "ubootfile=u-boot.bin\0" \
792 "upgrade=run flashworking\0" \
793 "workingaddr=0x02F00000\0" \
794 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
796 #else /* For Arcturus Modules */
798 #define CONFIG_EXTRA_ENV_SETTINGS \
799 "bootcmd=run norkernel\0" \
800 "bootfile=uImage\0" \
801 "consoledev=ttyS0\0" \
802 "dtbaddr=0x00c00000\0" \
803 "dtbfile=image.dtb\0" \
804 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
805 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
806 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
807 "fileaddr=0x01000000\0" \
808 "filesize=0x00080000\0" \
809 "flashmbr=sf probe 0; " \
810 "tftp $loadaddr $mbr; " \
811 "sf erase $mbr_offset +$filesize; " \
812 "sf write $loadaddr $mbr_offset $filesize\0" \
813 "flashuboot=tftp $loadaddr $ubootfile; " \
814 "protect off $nor_ubootaddr0 +$filesize; " \
815 "erase $nor_ubootaddr0 +$filesize; " \
816 "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \
817 "protect on $nor_ubootaddr0 +$filesize; " \
818 "protect off $nor_ubootaddr1 +$filesize; " \
819 "erase $nor_ubootaddr1 +$filesize; " \
820 "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \
821 "protect on $nor_ubootaddr1 +$filesize\0 " \
822 "format0=protect off $part0base +$part0size; " \
823 "erase $part0base +$part0size\0" \
824 "format1=protect off $part1base +$part1size; " \
825 "erase $part1base +$part1size\0" \
826 "format2=protect off $part2base +$part2size; " \
827 "erase $part2base +$part2size\0" \
828 "format3=protect off $part3base +$part3size; " \
829 "erase $part3base +$part3size\0" \
830 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
831 "kerneladdr=0x01100000\0" \
832 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \
833 "kernelfile=uImage\0" \
834 "loadaddr=0x01000000\0" \
835 "mbr=uCP1020.mbr\0" \
836 "mbr_offset=0x00000000\0" \
838 "nor_ubootaddr0=0xEC000000\0" \
839 "nor_ubootaddr1=0xEFF80000\0" \
840 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
841 "run norkernelload; " \
842 "bootm $kerneladdr - $dtbaddr\0" \
843 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \
844 "setenv cramfsaddr $part0base; " \
845 "cramfsload $dtbaddr $dtbfile; " \
846 "cramfsload $kerneladdr $kernelfile\0" \
847 "part0base=0xEC100000\0" \
848 "part0size=0x00700000\0" \
849 "part1base=0xEC800000\0" \
850 "part1size=0x02000000\0" \
851 "part2base=0xEE800000\0" \
852 "part2size=0x00800000\0" \
853 "part3base=0xEF000000\0" \
854 "part3size=0x00F80000\0" \
855 "partENVbase=0xEC080000\0" \
856 "partENVsize=0x00080000\0" \
857 "program0=tftp part0-000000.bin; " \
858 "protect off $part0base +$filesize; " \
859 "erase $part0base +$filesize; " \
860 "cp.b $loadaddr $part0base $filesize; " \
861 "echo Verifying...; " \
862 "cmp.b $loadaddr $part0base $filesize\0" \
863 "program1=tftp part1-000000.bin; " \
864 "protect off $part1base +$filesize; " \
865 "erase $part1base +$filesize; " \
866 "cp.b $loadaddr $part1base $filesize; " \
867 "echo Verifying...; " \
868 "cmp.b $loadaddr $part1base $filesize\0" \
869 "program2=tftp part2-000000.bin; " \
870 "protect off $part2base +$filesize; " \
871 "erase $part2base +$filesize; " \
872 "cp.b $loadaddr $part2base $filesize; " \
873 "echo Verifying...; " \
874 "cmp.b $loadaddr $part2base $filesize\0" \
875 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
876 " console=$consoledev,$baudrate $othbootargs; " \
877 "tftp $rootfsaddr $rootfsfile; " \
878 "tftp $loadaddr $kernelfile; " \
879 "tftp $dtbaddr $dtbfile; " \
880 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \
881 "ramdisk_size=120000\0" \
882 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
883 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
884 "mw.l 0xffe0f008 0x00400000\0" \
885 "rootfsaddr=0x02F00000\0" \
886 "rootfsfile=rootfs.ext2.gz.uboot\0" \
887 "rootpath=/opt/nfsroot\0" \
888 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
889 "sf probe 0; sf erase 0 +$filesize; " \
890 "sf write $loadaddr 0 $filesize\0" \
891 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
892 "protect off 0xeC000000 +$filesize; " \
893 "erase 0xEC000000 +$filesize; " \
894 "cp.b $loadaddr 0xEC000000 $filesize; " \
895 "cmp.b $loadaddr 0xEC000000 $filesize; " \
896 "protect on 0xeC000000 +$filesize\0" \
897 "tftpflash=tftpboot $loadaddr $uboot; " \
898 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
899 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
900 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
901 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
902 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
903 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
904 "ubootfile=u-boot.bin\0" \
905 "upgrade=run flashuboot\0" \
906 "usb_phy_type=ulpi\0 " \
908 "setenv bootargs root=/dev/nfs rw " \
909 "nfsroot=$serverip:$rootpath " \
910 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
911 "console=$consoledev,$baudrate $othbootargs;" \
912 "tftp $loadaddr $bootfile;" \
913 "tftp $fdtaddr $fdtfile;" \
914 "bootm $loadaddr - $fdtaddr\0" \
916 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
917 "console=$consoledev,$baudrate $othbootargs;" \
919 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
920 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
921 "bootm $loadaddr - $fdtaddr\0" \
923 "setenv bootargs root=/dev/ram rw " \
924 "console=$consoledev,$baudrate $othbootargs " \
925 "ramdisk_size=$ramdisk_size;" \
927 "fatload usb 0:2 $loadaddr $bootfile;" \
928 "fatload usb 0:2 $fdtaddr $fdtfile;" \
929 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
930 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
932 "setenv bootargs root=/dev/ram rw " \
933 "console=$consoledev,$baudrate $othbootargs " \
934 "ramdisk_size=$ramdisk_size;" \
936 "ext2load usb 0:4 $loadaddr $bootfile;" \
937 "ext2load usb 0:4 $fdtaddr $fdtfile;" \
938 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
939 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
941 "setenv bootargs root=/dev/$jffs2nor rw " \
942 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
943 "bootm $norbootaddr - $norfdtaddr\0 " \
945 "setenv bootargs root=/dev/ram rw " \
946 "console=$consoledev,$baudrate $othbootargs " \
947 "ramdisk_size=$ramdisk_size;" \
948 "tftp $ramdiskaddr $ramdiskfile;" \
949 "tftp $loadaddr $bootfile;" \
950 "tftp $fdtaddr $fdtfile;" \
951 "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
956 #endif /* __CONFIG_H */