2 * linux/include/linux/mtd/nand.h
4 * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org>
5 * Steven J. Hill <sjhill@realitydiluted.com>
6 * Thomas Gleixner <tglx@linutronix.de>
8 * SPDX-License-Identifier: GPL-2.0+
11 * Contains standard defines and IDs for NAND flash devices
16 #ifndef __LINUX_MTD_NAND_H
17 #define __LINUX_MTD_NAND_H
21 #include <linux/compat.h>
22 #include <linux/mtd/mtd.h>
23 #include <linux/mtd/flashchip.h>
24 #include <linux/mtd/bbm.h>
27 struct nand_flash_dev;
30 /* Scan and identify a NAND device */
31 int nand_scan(struct mtd_info *mtd, int max_chips);
33 * Separate phases of nand_scan(), allowing board driver to intervene
34 * and override command or ECC setup according to flash type.
36 int nand_scan_ident(struct mtd_info *mtd, int max_chips,
37 struct nand_flash_dev *table);
38 int nand_scan_tail(struct mtd_info *mtd);
40 /* Free resources held by the NAND device */
41 void nand_release(struct mtd_info *mtd);
43 /* Internal helper for board drivers which need to override command function */
44 void nand_wait_ready(struct mtd_info *mtd);
47 * This constant declares the max. oobsize / page, which
48 * is supported now. If you add a chip with bigger oobsize/page
49 * adjust this accordingly.
51 #define NAND_MAX_OOBSIZE 1664
52 #define NAND_MAX_PAGESIZE 16384
55 * Constants for hardware specific CLE/ALE/NCE function
57 * These are bits which can be or'ed to set/clear multiple
60 /* Select the chip by setting nCE to low */
62 /* Select the command latch by setting CLE to high */
64 /* Select the address latch by setting ALE to high */
67 #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE)
68 #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE)
69 #define NAND_CTRL_CHANGE 0x80
72 * Standard NAND flash commands
74 #define NAND_CMD_READ0 0
75 #define NAND_CMD_READ1 1
76 #define NAND_CMD_RNDOUT 5
77 #define NAND_CMD_PAGEPROG 0x10
78 #define NAND_CMD_READOOB 0x50
79 #define NAND_CMD_ERASE1 0x60
80 #define NAND_CMD_STATUS 0x70
81 #define NAND_CMD_SEQIN 0x80
82 #define NAND_CMD_RNDIN 0x85
83 #define NAND_CMD_READID 0x90
84 #define NAND_CMD_ERASE2 0xd0
85 #define NAND_CMD_PARAM 0xec
86 #define NAND_CMD_GET_FEATURES 0xee
87 #define NAND_CMD_SET_FEATURES 0xef
88 #define NAND_CMD_RESET 0xff
90 #define NAND_CMD_LOCK 0x2a
91 #define NAND_CMD_UNLOCK1 0x23
92 #define NAND_CMD_UNLOCK2 0x24
94 /* Extended commands for large page devices */
95 #define NAND_CMD_READSTART 0x30
96 #define NAND_CMD_RNDOUTSTART 0xE0
97 #define NAND_CMD_CACHEDPROG 0x15
99 /* Extended commands for AG-AND device */
101 * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but
102 * there is no way to distinguish that from NAND_CMD_READ0
103 * until the remaining sequence of commands has been completed
104 * so add a high order bit and mask it off in the command.
106 #define NAND_CMD_DEPLETE1 0x100
107 #define NAND_CMD_DEPLETE2 0x38
108 #define NAND_CMD_STATUS_MULTI 0x71
109 #define NAND_CMD_STATUS_ERROR 0x72
110 /* multi-bank error status (banks 0-3) */
111 #define NAND_CMD_STATUS_ERROR0 0x73
112 #define NAND_CMD_STATUS_ERROR1 0x74
113 #define NAND_CMD_STATUS_ERROR2 0x75
114 #define NAND_CMD_STATUS_ERROR3 0x76
115 #define NAND_CMD_STATUS_RESET 0x7f
116 #define NAND_CMD_STATUS_CLEAR 0xff
118 #define NAND_CMD_NONE -1
121 #define NAND_STATUS_FAIL 0x01
122 #define NAND_STATUS_FAIL_N1 0x02
123 #define NAND_STATUS_TRUE_READY 0x20
124 #define NAND_STATUS_READY 0x40
125 #define NAND_STATUS_WP 0x80
128 * Constants for ECC_MODES
134 NAND_ECC_HW_SYNDROME,
135 NAND_ECC_HW_OOB_FIRST,
140 * Constants for Hardware ECC
142 /* Reset Hardware ECC for read */
143 #define NAND_ECC_READ 0
144 /* Reset Hardware ECC for write */
145 #define NAND_ECC_WRITE 1
146 /* Enable Hardware ECC before syndrome is read back from flash */
147 #define NAND_ECC_READSYN 2
150 * Enable generic NAND 'page erased' check. This check is only done when
151 * ecc.correct() returns -EBADMSG.
152 * Set this flag if your implementation does not fix bitflips in erased
153 * pages and you want to rely on the default implementation.
155 #define NAND_ECC_GENERIC_ERASED_CHECK BIT(0)
156 #define NAND_ECC_MAXIMIZE BIT(1)
158 /* Bit mask for flags passed to do_nand_read_ecc */
159 #define NAND_GET_DEVICE 0x80
163 * Option constants for bizarre disfunctionality and real
166 /* Buswidth is 16 bit */
167 #define NAND_BUSWIDTH_16 0x00000002
168 /* Device supports partial programming without padding */
169 #define NAND_NO_PADDING 0x00000004
170 /* Chip has cache program function */
171 #define NAND_CACHEPRG 0x00000008
172 /* Chip has copy back function */
173 #define NAND_COPYBACK 0x00000010
175 * Chip requires ready check on read (for auto-incremented sequential read).
176 * True only for small page devices; large page devices do not support
179 #define NAND_NEED_READRDY 0x00000100
181 /* Chip does not allow subpage writes */
182 #define NAND_NO_SUBPAGE_WRITE 0x00000200
184 /* Device is one of 'new' xD cards that expose fake nand command set */
185 #define NAND_BROKEN_XD 0x00000400
187 /* Device behaves just like nand, but is readonly */
188 #define NAND_ROM 0x00000800
190 /* Device supports subpage reads */
191 #define NAND_SUBPAGE_READ 0x00001000
194 * Some MLC NANDs need data scrambling to limit bitflips caused by repeated
197 #define NAND_NEED_SCRAMBLING 0x00002000
199 /* Options valid for Samsung large page devices */
200 #define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG
202 /* Macros to identify the above */
203 #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG))
204 #define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ))
206 /* Non chip related options */
207 /* This option skips the bbt scan during initialization. */
208 #define NAND_SKIP_BBTSCAN 0x00010000
210 * This option is defined if the board driver allocates its own buffers
211 * (e.g. because it needs them DMA-coherent).
213 #define NAND_OWN_BUFFERS 0x00020000
214 /* Chip may not exist, so silence any errors in scan */
215 #define NAND_SCAN_SILENT_NODEV 0x00040000
217 * Autodetect nand buswidth with readid/onfi.
218 * This suppose the driver will configure the hardware in 8 bits mode
219 * when calling nand_scan_ident, and update its configuration
220 * before calling nand_scan_tail.
222 #define NAND_BUSWIDTH_AUTO 0x00080000
224 * This option could be defined by controller drivers to protect against
225 * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers
227 #define NAND_USE_BOUNCE_BUFFER 0x00100000
229 /* Options set by nand scan */
230 /* bbt has already been read */
231 #define NAND_BBT_SCANNED 0x40000000
232 /* Nand scan has allocated controller struct */
233 #define NAND_CONTROLLER_ALLOC 0x80000000
235 /* Cell info constants */
236 #define NAND_CI_CHIPNR_MSK 0x03
237 #define NAND_CI_CELLTYPE_MSK 0x0C
238 #define NAND_CI_CELLTYPE_SHIFT 2
244 #define ONFI_FEATURE_16_BIT_BUS (1 << 0)
245 #define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7)
247 /* ONFI timing mode, used in both asynchronous and synchronous mode */
248 #define ONFI_TIMING_MODE_0 (1 << 0)
249 #define ONFI_TIMING_MODE_1 (1 << 1)
250 #define ONFI_TIMING_MODE_2 (1 << 2)
251 #define ONFI_TIMING_MODE_3 (1 << 3)
252 #define ONFI_TIMING_MODE_4 (1 << 4)
253 #define ONFI_TIMING_MODE_5 (1 << 5)
254 #define ONFI_TIMING_MODE_UNKNOWN (1 << 6)
256 /* ONFI feature address */
257 #define ONFI_FEATURE_ADDR_TIMING_MODE 0x1
259 /* Vendor-specific feature address (Micron) */
260 #define ONFI_FEATURE_ADDR_READ_RETRY 0x89
262 /* ONFI subfeature parameters length */
263 #define ONFI_SUBFEATURE_PARAM_LEN 4
265 /* ONFI optional commands SET/GET FEATURES supported? */
266 #define ONFI_OPT_CMD_SET_GET_FEATURES (1 << 2)
268 struct nand_onfi_params {
269 /* rev info and features block */
270 /* 'O' 'N' 'F' 'I' */
276 __le16 ext_param_page_length; /* since ONFI 2.1 */
277 u8 num_of_param_pages; /* since ONFI 2.1 */
280 /* manufacturer information block */
281 char manufacturer[12];
287 /* memory organization block */
288 __le32 byte_per_page;
289 __le16 spare_bytes_per_page;
290 __le32 data_bytes_per_ppage;
291 __le16 spare_bytes_per_ppage;
292 __le32 pages_per_block;
293 __le32 blocks_per_lun;
298 __le16 block_endurance;
299 u8 guaranteed_good_blocks;
300 __le16 guaranteed_block_endurance;
301 u8 programs_per_page;
308 /* electrical parameter block */
309 u8 io_pin_capacitance_max;
310 __le16 async_timing_mode;
311 __le16 program_cache_timing_mode;
316 __le16 src_sync_timing_mode;
317 u8 src_ssync_features;
318 __le16 clk_pin_capacitance_typ;
319 __le16 io_pin_capacitance_typ;
320 __le16 input_pin_capacitance_typ;
321 u8 input_pin_capacitance_max;
322 u8 driver_strength_support;
328 __le16 vendor_revision;
334 #define ONFI_CRC_BASE 0x4F4E
336 /* Extended ECC information Block Definition (since ONFI 2.1) */
337 struct onfi_ext_ecc_info {
341 __le16 block_endurance;
345 #define ONFI_SECTION_TYPE_0 0 /* Unused section. */
346 #define ONFI_SECTION_TYPE_1 1 /* for additional sections. */
347 #define ONFI_SECTION_TYPE_2 2 /* for ECC information. */
348 struct onfi_ext_section {
353 #define ONFI_EXT_SECTION_MAX 8
355 /* Extended Parameter Page Definition (since ONFI 2.1) */
356 struct onfi_ext_param_page {
358 u8 sig[4]; /* 'E' 'P' 'P' 'S' */
360 struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX];
363 * The actual size of the Extended Parameter Page is in
364 * @ext_param_page_length of nand_onfi_params{}.
365 * The following are the variable length sections.
366 * So we do not add any fields below. Please see the ONFI spec.
370 struct nand_onfi_vendor_micron {
375 u8 dq_imped_num_settings;
376 u8 dq_imped_feat_addr;
377 u8 rb_pulldown_strength;
378 u8 rb_pulldown_strength_feat_addr;
379 u8 rb_pulldown_strength_num_settings;
382 u8 otp_data_prot_addr;
385 u8 read_retry_options;
390 struct jedec_ecc_info {
394 __le16 block_endurance;
399 #define JEDEC_FEATURE_16_BIT_BUS (1 << 0)
401 struct nand_jedec_params {
402 /* rev info and features block */
403 /* 'J' 'E' 'S' 'D' */
409 u8 num_of_param_pages;
412 /* manufacturer information block */
413 char manufacturer[12];
418 /* memory organization block */
419 __le32 byte_per_page;
420 __le16 spare_bytes_per_page;
422 __le32 pages_per_block;
423 __le32 blocks_per_lun;
427 u8 programs_per_page;
429 u8 multi_plane_op_attr;
432 /* electrical parameter block */
433 __le16 async_sdr_speed_grade;
434 __le16 toggle_ddr_speed_grade;
435 __le16 sync_ddr_speed_grade;
436 u8 async_sdr_features;
437 u8 toggle_ddr_features;
438 u8 sync_ddr_features;
442 __le16 t_r_multi_plane;
444 __le16 io_pin_capacitance_typ;
445 __le16 input_pin_capacitance_typ;
446 __le16 clk_pin_capacitance_typ;
447 u8 driver_strength_support;
451 /* ECC and endurance block */
452 u8 guaranteed_good_blocks;
453 __le16 guaranteed_block_endurance;
454 struct jedec_ecc_info ecc_info[4];
461 __le16 vendor_rev_num;
464 /* CRC for Parameter Page */
469 * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices
470 * @lock: protection lock
471 * @active: the mtd device which holds the controller currently
472 * @wq: wait queue to sleep on if a NAND operation is in
473 * progress used instead of the per chip wait queue
474 * when a hw controller is available.
476 struct nand_hw_control {
478 struct nand_chip *active;
482 * struct nand_ecc_ctrl - Control structure for ECC
484 * @steps: number of ECC steps per page
485 * @size: data bytes per ECC step
486 * @bytes: ECC bytes per step
487 * @strength: max number of correctible bits per ECC step
488 * @total: total number of ECC bytes per page
489 * @prepad: padding information for syndrome based ECC generators
490 * @postpad: padding information for syndrome based ECC generators
491 * @options: ECC specific options (see NAND_ECC_XXX flags defined above)
492 * @layout: ECC layout control struct pointer
493 * @priv: pointer to private ECC control data
494 * @hwctl: function to control hardware ECC generator. Must only
495 * be provided if an hardware ECC is available
496 * @calculate: function for ECC calculation or readback from ECC hardware
497 * @correct: function for ECC correction, matching to ECC generator (sw/hw).
498 * Should return a positive number representing the number of
499 * corrected bitflips, -EBADMSG if the number of bitflips exceed
500 * ECC strength, or any other error code if the error is not
501 * directly related to correction.
502 * If -EBADMSG is returned the input buffers should be left
504 * @read_page_raw: function to read a raw page without ECC. This function
505 * should hide the specific layout used by the ECC
506 * controller and always return contiguous in-band and
507 * out-of-band data even if they're not stored
508 * contiguously on the NAND chip (e.g.
509 * NAND_ECC_HW_SYNDROME interleaves in-band and
511 * @write_page_raw: function to write a raw page without ECC. This function
512 * should hide the specific layout used by the ECC
513 * controller and consider the passed data as contiguous
514 * in-band and out-of-band data. ECC controller is
515 * responsible for doing the appropriate transformations
516 * to adapt to its specific layout (e.g.
517 * NAND_ECC_HW_SYNDROME interleaves in-band and
519 * @read_page: function to read a page according to the ECC generator
520 * requirements; returns maximum number of bitflips corrected in
521 * any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
522 * @read_subpage: function to read parts of the page covered by ECC;
523 * returns same as read_page()
524 * @write_subpage: function to write parts of the page covered by ECC.
525 * @write_page: function to write a page according to the ECC generator
527 * @write_oob_raw: function to write chip OOB data without ECC
528 * @read_oob_raw: function to read chip OOB data without ECC
529 * @read_oob: function to read chip OOB data
530 * @write_oob: function to write chip OOB data
532 struct nand_ecc_ctrl {
533 nand_ecc_modes_t mode;
541 unsigned int options;
542 struct nand_ecclayout *layout;
544 void (*hwctl)(struct mtd_info *mtd, int mode);
545 int (*calculate)(struct mtd_info *mtd, const uint8_t *dat,
547 int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc,
549 int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip,
550 uint8_t *buf, int oob_required, int page);
551 int (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip,
552 const uint8_t *buf, int oob_required, int page);
553 int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip,
554 uint8_t *buf, int oob_required, int page);
555 int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
556 uint32_t offs, uint32_t len, uint8_t *buf, int page);
557 int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
558 uint32_t offset, uint32_t data_len,
559 const uint8_t *data_buf, int oob_required, int page);
560 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
561 const uint8_t *buf, int oob_required, int page);
562 int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
564 int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
566 int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page);
567 int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip,
572 * struct nand_buffers - buffer structure for read/write
573 * @ecccalc: buffer pointer for calculated ECC, size is oobsize.
574 * @ecccode: buffer pointer for ECC read from flash, size is oobsize.
575 * @databuf: buffer pointer for data, size is (page size + oobsize).
577 * Do not change the order of buffers. databuf and oobrbuf must be in
580 struct nand_buffers {
581 uint8_t ecccalc[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)];
582 uint8_t ecccode[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)];
583 uint8_t databuf[ALIGN(NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE,
588 * struct nand_chip - NAND Private Flash Chip Data
589 * @mtd: MTD device registered to the MTD framework
590 * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the
592 * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the
594 * @flash_node: [BOARDSPECIFIC] device node describing this instance
595 * @read_byte: [REPLACEABLE] read one byte from the chip
596 * @read_word: [REPLACEABLE] read one word from the chip
597 * @write_byte: [REPLACEABLE] write a single byte to the chip on the
599 * @write_buf: [REPLACEABLE] write data from the buffer to the chip
600 * @read_buf: [REPLACEABLE] read data from the chip into the buffer
601 * @select_chip: [REPLACEABLE] select chip nr
602 * @block_bad: [REPLACEABLE] check if a block is bad, using OOB markers
603 * @block_markbad: [REPLACEABLE] mark a block bad
604 * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling
605 * ALE/CLE/nCE. Also used to write command and address
606 * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing
607 * device ready/busy line. If set to NULL no access to
608 * ready/busy is available and the ready/busy information
609 * is read from the chip status register.
610 * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing
611 * commands to the chip.
612 * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on
614 * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for
615 * setting the read-retry mode. Mostly needed for MLC NAND.
616 * @ecc: [BOARDSPECIFIC] ECC control structure
617 * @buffers: buffer structure for read/write
618 * @hwcontrol: platform-specific hardware control structure
619 * @erase: [REPLACEABLE] erase function
620 * @scan_bbt: [REPLACEABLE] function to scan bad block table
621 * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring
622 * data from array to read regs (tR).
623 * @state: [INTERN] the current state of the NAND device
624 * @oob_poi: "poison value buffer," used for laying out OOB data
626 * @page_shift: [INTERN] number of address bits in a page (column
628 * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock
629 * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry
630 * @chip_shift: [INTERN] number of address bits in one chip
631 * @options: [BOARDSPECIFIC] various chip options. They can partly
632 * be set to inform nand_scan about special functionality.
633 * See the defines for further explanation.
634 * @bbt_options: [INTERN] bad block specific options. All options used
635 * here must come from bbm.h. By default, these options
636 * will be copied to the appropriate nand_bbt_descr's.
637 * @badblockpos: [INTERN] position of the bad block marker in the oob
639 * @badblockbits: [INTERN] minimum number of set bits in a good block's
640 * bad block marker position; i.e., BBM == 11110111b is
641 * not bad when badblockbits == 7
642 * @bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC.
643 * @ecc_strength_ds: [INTERN] ECC correctability from the datasheet.
644 * Minimum amount of bit errors per @ecc_step_ds guaranteed
645 * to be correctable. If unknown, set to zero.
646 * @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds,
647 * also from the datasheet. It is the recommended ECC step
648 * size, if known; if unknown, set to zero.
649 * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is
650 * either deduced from the datasheet if the NAND
651 * chip is not ONFI compliant or set to 0 if it is
652 * (an ONFI chip is always configured in mode 0
653 * after a NAND reset)
654 * @numchips: [INTERN] number of physical chips
655 * @chipsize: [INTERN] the size of one chip for multichip arrays
656 * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1
657 * @pagebuf: [INTERN] holds the pagenumber which is currently in
659 * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is
660 * currently in data_buf.
661 * @subpagesize: [INTERN] holds the subpagesize
662 * @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded),
663 * non 0 if ONFI supported.
664 * @jedec_version: [INTERN] holds the chip JEDEC version (BCD encoded),
665 * non 0 if JEDEC supported.
666 * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is
667 * supported, 0 otherwise.
668 * @jedec_params: [INTERN] holds the JEDEC parameter page when JEDEC is
669 * supported, 0 otherwise.
670 * @read_retries: [INTERN] the number of read retry modes supported
671 * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand
672 * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand
673 * @bbt: [INTERN] bad block table pointer
674 * @bbt_td: [REPLACEABLE] bad block table descriptor for flash
676 * @bbt_md: [REPLACEABLE] bad block table mirror descriptor
677 * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial
679 * @controller: [REPLACEABLE] a pointer to a hardware controller
680 * structure which is shared among multiple independent
682 * @priv: [OPTIONAL] pointer to private chip data
683 * @errstat: [OPTIONAL] hardware specific function to perform
684 * additional error status checks (determine if errors are
686 * @write_page: [REPLACEABLE] High-level page write function
691 void __iomem *IO_ADDR_R;
692 void __iomem *IO_ADDR_W;
696 uint8_t (*read_byte)(struct mtd_info *mtd);
697 u16 (*read_word)(struct mtd_info *mtd);
698 void (*write_byte)(struct mtd_info *mtd, uint8_t byte);
699 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
700 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
701 void (*select_chip)(struct mtd_info *mtd, int chip);
702 int (*block_bad)(struct mtd_info *mtd, loff_t ofs);
703 int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
704 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
705 int (*dev_ready)(struct mtd_info *mtd);
706 void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column,
708 int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this);
709 int (*erase)(struct mtd_info *mtd, int page);
710 int (*scan_bbt)(struct mtd_info *mtd);
711 int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state,
712 int status, int page);
713 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
714 uint32_t offset, int data_len, const uint8_t *buf,
715 int oob_required, int page, int cached, int raw);
716 int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip,
717 int feature_addr, uint8_t *subfeature_para);
718 int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip,
719 int feature_addr, uint8_t *subfeature_para);
720 int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode);
723 unsigned int options;
724 unsigned int bbt_options;
727 int phys_erase_shift;
734 unsigned int pagebuf_bitflips;
736 uint8_t bits_per_cell;
737 uint16_t ecc_strength_ds;
738 uint16_t ecc_step_ds;
739 int onfi_timing_mode_default;
745 struct nand_onfi_params onfi_params;
746 struct nand_jedec_params jedec_params;
753 struct nand_hw_control *controller;
754 struct nand_ecclayout *ecclayout;
756 struct nand_ecc_ctrl ecc;
757 struct nand_buffers *buffers;
758 struct nand_hw_control hwcontrol;
761 struct nand_bbt_descr *bbt_td;
762 struct nand_bbt_descr *bbt_md;
764 struct nand_bbt_descr *badblock_pattern;
769 static inline struct nand_chip *mtd_to_nand(struct mtd_info *mtd)
771 return container_of(mtd, struct nand_chip, mtd);
774 static inline struct mtd_info *nand_to_mtd(struct nand_chip *chip)
779 static inline void *nand_get_controller_data(struct nand_chip *chip)
784 static inline void nand_set_controller_data(struct nand_chip *chip, void *priv)
790 * NAND Flash Manufacturer ID Codes
792 #define NAND_MFR_TOSHIBA 0x98
793 #define NAND_MFR_SAMSUNG 0xec
794 #define NAND_MFR_FUJITSU 0x04
795 #define NAND_MFR_NATIONAL 0x8f
796 #define NAND_MFR_RENESAS 0x07
797 #define NAND_MFR_STMICRO 0x20
798 #define NAND_MFR_HYNIX 0xad
799 #define NAND_MFR_MICRON 0x2c
800 #define NAND_MFR_AMD 0x01
801 #define NAND_MFR_MACRONIX 0xc2
802 #define NAND_MFR_EON 0x92
803 #define NAND_MFR_SANDISK 0x45
804 #define NAND_MFR_INTEL 0x89
805 #define NAND_MFR_ATO 0x9b
807 /* The maximum expected count of bytes in the NAND ID sequence */
808 #define NAND_MAX_ID_LEN 8
811 * A helper for defining older NAND chips where the second ID byte fully
812 * defined the chip, including the geometry (chip size, eraseblock size, page
813 * size). All these chips have 512 bytes NAND page size.
815 #define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \
816 { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \
817 .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) }
820 * A helper for defining newer chips which report their page size and
821 * eraseblock size via the extended ID bytes.
823 * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with
824 * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the
825 * device ID now only represented a particular total chip size (and voltage,
826 * buswidth), and the page size, eraseblock size, and OOB size could vary while
827 * using the same device ID.
829 #define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \
830 { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \
833 #define NAND_ECC_INFO(_strength, _step) \
834 { .strength_ds = (_strength), .step_ds = (_step) }
835 #define NAND_ECC_STRENGTH(type) ((type)->ecc.strength_ds)
836 #define NAND_ECC_STEP(type) ((type)->ecc.step_ds)
839 * struct nand_flash_dev - NAND Flash Device ID Structure
840 * @name: a human-readable name of the NAND chip
841 * @dev_id: the device ID (the second byte of the full chip ID array)
842 * @mfr_id: manufecturer ID part of the full chip ID array (refers the same
843 * memory address as @id[0])
844 * @dev_id: device ID part of the full chip ID array (refers the same memory
846 * @id: full device ID array
847 * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as
848 * well as the eraseblock size) is determined from the extended NAND
850 * @chipsize: total chip size in MiB
851 * @erasesize: eraseblock size in bytes (determined from the extended ID if 0)
852 * @options: stores various chip bit options
853 * @id_len: The valid length of the @id.
855 * @ecc: ECC correctability and step information from the datasheet.
856 * @ecc.strength_ds: The ECC correctability from the datasheet, same as the
857 * @ecc_strength_ds in nand_chip{}.
858 * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
859 * @ecc_step_ds in nand_chip{}, also from the datasheet.
860 * For example, the "4bit ECC for each 512Byte" can be set with
861 * NAND_ECC_INFO(4, 512).
862 * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND
863 * reset. Should be deduced from timings described
867 struct nand_flash_dev {
874 uint8_t id[NAND_MAX_ID_LEN];
876 unsigned int pagesize;
877 unsigned int chipsize;
878 unsigned int erasesize;
879 unsigned int options;
883 uint16_t strength_ds;
886 int onfi_timing_mode_default;
890 * struct nand_manufacturers - NAND Flash Manufacturer ID Structure
891 * @name: Manufacturer name
892 * @id: manufacturer ID code of device.
894 struct nand_manufacturers {
899 extern struct nand_flash_dev nand_flash_ids[];
900 extern struct nand_manufacturers nand_manuf_ids[];
902 int nand_default_bbt(struct mtd_info *mtd);
903 int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs);
904 int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs);
905 int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt);
906 int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
908 int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len,
909 size_t *retlen, uint8_t *buf);
912 * Constants for oob configuration
914 #define NAND_SMALL_BADBLOCK_POS 5
915 #define NAND_LARGE_BADBLOCK_POS 0
918 * struct platform_nand_chip - chip level device structure
919 * @nr_chips: max. number of chips to scan for
920 * @chip_offset: chip number offset
921 * @nr_partitions: number of partitions pointed to by partitions (or zero)
922 * @partitions: mtd partition list
923 * @chip_delay: R/B delay value in us
924 * @options: Option flags, e.g. 16bit buswidth
925 * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH
926 * @part_probe_types: NULL-terminated array of probe types
928 struct platform_nand_chip {
932 struct mtd_partition *partitions;
934 unsigned int options;
935 unsigned int bbt_options;
936 const char **part_probe_types;
940 struct platform_device;
943 * struct platform_nand_ctrl - controller level device structure
944 * @probe: platform specific function to probe/setup hardware
945 * @remove: platform specific function to remove/teardown hardware
946 * @hwcontrol: platform specific hardware control structure
947 * @dev_ready: platform specific function to read ready/busy pin
948 * @select_chip: platform specific chip select function
949 * @cmd_ctrl: platform specific function for controlling
950 * ALE/CLE/nCE. Also used to write command and address
951 * @write_buf: platform specific function for write buffer
952 * @read_buf: platform specific function for read buffer
953 * @read_byte: platform specific function to read one byte from chip
954 * @priv: private data to transport driver specific settings
956 * All fields are optional and depend on the hardware driver requirements
958 struct platform_nand_ctrl {
959 int (*probe)(struct platform_device *pdev);
960 void (*remove)(struct platform_device *pdev);
961 void (*hwcontrol)(struct mtd_info *mtd, int cmd);
962 int (*dev_ready)(struct mtd_info *mtd);
963 void (*select_chip)(struct mtd_info *mtd, int chip);
964 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
965 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
966 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
967 unsigned char (*read_byte)(struct mtd_info *mtd);
972 * struct platform_nand_data - container structure for platform-specific data
973 * @chip: chip level chip structure
974 * @ctrl: controller level device structure
976 struct platform_nand_data {
977 struct platform_nand_chip chip;
978 struct platform_nand_ctrl ctrl;
981 #ifdef CONFIG_SYS_NAND_ONFI_DETECTION
982 /* return the supported features. */
983 static inline int onfi_feature(struct nand_chip *chip)
985 return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0;
988 /* return the supported asynchronous timing mode. */
989 static inline int onfi_get_async_timing_mode(struct nand_chip *chip)
991 if (!chip->onfi_version)
992 return ONFI_TIMING_MODE_UNKNOWN;
993 return le16_to_cpu(chip->onfi_params.async_timing_mode);
996 /* return the supported synchronous timing mode. */
997 static inline int onfi_get_sync_timing_mode(struct nand_chip *chip)
999 if (!chip->onfi_version)
1000 return ONFI_TIMING_MODE_UNKNOWN;
1001 return le16_to_cpu(chip->onfi_params.src_sync_timing_mode);
1004 static inline int onfi_feature(struct nand_chip *chip)
1009 static inline int onfi_get_async_timing_mode(struct nand_chip *chip)
1011 return ONFI_TIMING_MODE_UNKNOWN;
1014 static inline int onfi_get_sync_timing_mode(struct nand_chip *chip)
1016 return ONFI_TIMING_MODE_UNKNOWN;
1021 * Check if it is a SLC nand.
1022 * The !nand_is_slc() can be used to check the MLC/TLC nand chips.
1023 * We do not distinguish the MLC and TLC now.
1025 static inline bool nand_is_slc(struct nand_chip *chip)
1027 return chip->bits_per_cell == 1;
1031 * Check if the opcode's address should be sent only on the lower 8 bits
1032 * @command: opcode to check
1034 static inline int nand_opcode_8bits(unsigned int command)
1037 case NAND_CMD_READID:
1038 case NAND_CMD_PARAM:
1039 case NAND_CMD_GET_FEATURES:
1040 case NAND_CMD_SET_FEATURES:
1048 /* return the supported JEDEC features. */
1049 static inline int jedec_feature(struct nand_chip *chip)
1051 return chip->jedec_version ? le16_to_cpu(chip->jedec_params.features)
1055 /* Standard NAND functions from nand_base.c */
1056 void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len);
1057 void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len);
1058 void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len);
1059 void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len);
1060 uint8_t nand_read_byte(struct mtd_info *mtd);
1063 * struct nand_sdr_timings - SDR NAND chip timings
1065 * This struct defines the timing requirements of a SDR NAND chip.
1066 * These informations can be found in every NAND datasheets and the timings
1067 * meaning are described in the ONFI specifications:
1068 * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
1071 * All these timings are expressed in picoseconds.
1074 struct nand_sdr_timings {
1111 /* get timing characteristics from ONFI timing mode. */
1112 const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode);
1114 int nand_check_erased_ecc_chunk(void *data, int datalen,
1115 void *ecc, int ecclen,
1116 void *extraoob, int extraooblen,
1118 #endif /* __LINUX_MTD_NAND_H */