1 /**************************************************************************
2 * Copyright (C) 2012 by Andreas Fritiofson *
3 * andreas.fritiofson@gmail.com *
5 * This program is free software; you can redistribute it and/or modify *
6 * it under the terms of the GNU General Public License as published by *
7 * the Free Software Foundation; either version 2 of the License, or *
8 * (at your option) any later version. *
10 * This program is distributed in the hope that it will be useful, *
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of *
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the *
13 * GNU General Public License for more details. *
15 * You should have received a copy of the GNU General Public License *
16 * along with this program; if not, write to the *
17 * Free Software Foundation, Inc., *
18 * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. *
19 ***************************************************************************/
23 * JTAG adapters based on the FT2232 full and high speed USB parts are
24 * popular low cost JTAG debug solutions. Many FT2232 based JTAG adapters
25 * are discrete, but development boards may integrate them as alternatives
26 * to more capable (and expensive) third party JTAG pods.
28 * JTAG uses only one of the two communications channels ("MPSSE engines")
29 * on these devices. Adapters based on FT4232 parts have four ports/channels
30 * (A/B/C/D), instead of just two (A/B).
32 * Especially on development boards integrating one of these chips (as
33 * opposed to discrete pods/dongles), the additional channels can be used
34 * for a variety of purposes, but OpenOCD only uses one channel at a time.
36 * - As a USB-to-serial adapter for the target's console UART ...
37 * which may be able to support ROM boot loaders that load initial
38 * firmware images to flash (or SRAM).
40 * - On systems which support ARM's SWD in addition to JTAG, or instead
41 * of it, that second port can be used for reading SWV/SWO trace data.
43 * - Additional JTAG links, e.g. to a CPLD or * FPGA.
45 * FT2232 based JTAG adapters are "dumb" not "smart", because most JTAG
46 * request/response interactions involve round trips over the USB link.
47 * A "smart" JTAG adapter has intelligence close to the scan chain, so it
48 * can for example poll quickly for a status change (usually taking on the
49 * order of microseconds not milliseconds) before beginning a queued
50 * transaction which require the previous one to have completed.
52 * There are dozens of adapters of this type, differing in details which
53 * this driver needs to understand. Those "layout" details are required
54 * as part of FT2232 driver configuration.
56 * This code uses information contained in the MPSSE specification which was
58 * http://www.ftdichip.com/Documents/AppNotes/AN2232C-01_MPSSE_Cmnd.pdf
59 * Hereafter this is called the "MPSSE Spec".
61 * The datasheet for the ftdichip.com's FT2232D part is here:
62 * http://www.ftdichip.com/Documents/DataSheets/DS_FT2232D.pdf
64 * Also note the issue with code 0x4b (clock data to TMS) noted in
65 * http://developer.intra2net.com/mailarchive/html/libftdi/2009/msg00292.html
66 * which can affect longer JTAG state paths.
73 /* project specific includes */
74 #include <jtag/interface.h>
75 #include <transport/transport.h>
76 #include <helper/time_support.h>
84 /* FTDI access library includes */
87 #define JTAG_MODE (LSB_FIRST | POS_EDGE_IN | NEG_EDGE_OUT)
89 static char *ftdi_device_desc;
90 static char *ftdi_serial;
91 static uint8_t ftdi_channel;
94 /* vid = pid = 0 marks the end of the list */
95 static uint16_t ftdi_vid[MAX_USB_IDS + 1] = { 0 };
96 static uint16_t ftdi_pid[MAX_USB_IDS + 1] = { 0 };
98 static struct mpsse_ctx *mpsse_ctx;
109 static struct signal *signals;
111 static uint16_t output;
112 static uint16_t direction;
114 static struct signal *find_signal_by_name(const char *name)
116 for (struct signal *sig = signals; sig; sig = sig->next) {
117 if (strcmp(name, sig->name) == 0)
123 static struct signal *create_signal(const char *name)
125 struct signal **psig = &signals;
127 psig = &(*psig)->next;
129 *psig = calloc(1, sizeof(**psig));
133 (*psig)->name = strdup(name);
134 if ((*psig)->name == NULL) {
141 static int ftdi_set_signal(const struct signal *s, char value)
147 if (s->data_mask == 0 && s->oe_mask == 0) {
148 LOG_ERROR("interface doesn't provide signal '%s'", s->name);
153 data = s->invert_data;
157 if (s->data_mask == 0) {
158 LOG_ERROR("interface can't drive '%s' high", s->name);
161 data = !s->invert_data;
166 if (s->oe_mask == 0) {
167 LOG_ERROR("interface can't tri-state '%s'", s->name);
170 data = s->invert_data;
174 assert(0 && "invalid signal level specifier");
178 output = data ? output | s->data_mask : output & ~s->data_mask;
179 if (s->oe_mask == s->data_mask)
180 direction = oe ? direction | s->oe_mask : direction & ~s->oe_mask;
182 output = oe ? output | s->oe_mask : output & ~s->oe_mask;
184 retval = mpsse_set_data_bits_low_byte(mpsse_ctx, output & 0xff, direction & 0xff);
185 if (retval == ERROR_OK)
186 retval = mpsse_set_data_bits_high_byte(mpsse_ctx, output >> 8, direction >> 8);
187 if (retval != ERROR_OK) {
188 LOG_ERROR("couldn't initialize FTDI GPIO");
189 return ERROR_JTAG_INIT_FAILED;
197 * Function move_to_state
198 * moves the TAP controller from the current state to a
199 * \a goal_state through a path given by tap_get_tms_path(). State transition
200 * logging is performed by delegation to clock_tms().
202 * @param goal_state is the destination state for the move.
204 static int move_to_state(tap_state_t goal_state)
206 tap_state_t start_state = tap_get_state();
208 /* goal_state is 1/2 of a tuple/pair of states which allow convenient
209 lookup of the required TMS pattern to move to this state from the
213 /* do the 2 lookups */
214 int tms_bits = tap_get_tms_path(start_state, goal_state);
215 int tms_count = tap_get_tms_path_len(start_state, goal_state);
217 DEBUG_JTAG_IO("start=%s goal=%s", tap_state_name(start_state), tap_state_name(goal_state));
219 /* Track state transitions step by step */
220 for (int i = 0; i < tms_count; i++)
221 tap_set_state(tap_state_transition(tap_get_state(), (tms_bits >> i) & 1));
223 return mpsse_clock_tms_cs_out(mpsse_ctx,
224 (uint8_t *)&tms_bits,
231 static int ftdi_speed(int speed)
234 retval = mpsse_set_frequency(mpsse_ctx, speed);
237 LOG_ERROR("couldn't set FTDI TCK speed");
244 static int ftdi_speed_div(int speed, int *khz)
250 static int ftdi_khz(int khz, int *jtag_speed)
252 if (khz == 0 && !mpsse_is_high_speed(mpsse_ctx)) {
253 LOG_DEBUG("RCLK not supported");
257 *jtag_speed = khz * 1000;
261 static void ftdi_end_state(tap_state_t state)
263 if (tap_is_state_stable(state))
264 tap_set_end_state(state);
266 LOG_ERROR("BUG: %s is not a stable end state", tap_state_name(state));
271 static int ftdi_execute_runtest(struct jtag_command *cmd)
273 int retval = ERROR_OK;
277 DEBUG_JTAG_IO("runtest %i cycles, end in %s",
278 cmd->cmd.runtest->num_cycles,
279 tap_state_name(cmd->cmd.runtest->end_state));
281 if (tap_get_state() != TAP_IDLE)
282 move_to_state(TAP_IDLE);
284 /* TODO: Reuse ftdi_execute_stableclocks */
285 i = cmd->cmd.runtest->num_cycles;
286 while (i > 0 && retval == ERROR_OK) {
287 /* there are no state transitions in this code, so omit state tracking */
288 unsigned this_len = i > 7 ? 7 : i;
289 retval = mpsse_clock_tms_cs_out(mpsse_ctx, &zero, 0, this_len, false, JTAG_MODE);
293 ftdi_end_state(cmd->cmd.runtest->end_state);
295 if (tap_get_state() != tap_get_end_state())
296 move_to_state(tap_get_end_state());
298 DEBUG_JTAG_IO("runtest: %i, end in %s",
299 cmd->cmd.runtest->num_cycles,
300 tap_state_name(tap_get_end_state()));
304 static int ftdi_execute_statemove(struct jtag_command *cmd)
306 int retval = ERROR_OK;
308 DEBUG_JTAG_IO("statemove end in %s",
309 tap_state_name(cmd->cmd.statemove->end_state));
311 ftdi_end_state(cmd->cmd.statemove->end_state);
313 /* shortest-path move to desired end state */
314 if (tap_get_state() != tap_get_end_state() || tap_get_end_state() == TAP_RESET)
315 move_to_state(tap_get_end_state());
321 * Clock a bunch of TMS (or SWDIO) transitions, to change the JTAG
322 * (or SWD) state machine. REVISIT: Not the best method, perhaps.
324 static int ftdi_execute_tms(struct jtag_command *cmd)
326 DEBUG_JTAG_IO("TMS: %d bits", cmd->cmd.tms->num_bits);
328 /* TODO: Missing tap state tracking, also missing from ft2232.c! */
329 return mpsse_clock_tms_cs_out(mpsse_ctx,
332 cmd->cmd.tms->num_bits,
337 static int ftdi_execute_pathmove(struct jtag_command *cmd)
339 int retval = ERROR_OK;
341 tap_state_t *path = cmd->cmd.pathmove->path;
342 int num_states = cmd->cmd.pathmove->num_states;
344 DEBUG_JTAG_IO("pathmove: %i states, current: %s end: %s", num_states,
345 tap_state_name(tap_get_state()),
346 tap_state_name(path[num_states-1]));
349 unsigned bit_count = 0;
350 uint8_t tms_byte = 0;
354 /* this loop verifies that the path is legal and logs each state in the path */
355 while (num_states-- && retval == ERROR_OK) {
357 /* either TMS=0 or TMS=1 must work ... */
358 if (tap_state_transition(tap_get_state(), false)
359 == path[state_count])
360 buf_set_u32(&tms_byte, bit_count++, 1, 0x0);
361 else if (tap_state_transition(tap_get_state(), true)
362 == path[state_count]) {
363 buf_set_u32(&tms_byte, bit_count++, 1, 0x1);
365 /* ... or else the caller goofed BADLY */
367 LOG_ERROR("BUG: %s -> %s isn't a valid "
368 "TAP state transition",
369 tap_state_name(tap_get_state()),
370 tap_state_name(path[state_count]));
374 tap_set_state(path[state_count]);
377 if (bit_count == 7 || num_states == 0) {
378 retval = mpsse_clock_tms_cs_out(mpsse_ctx,
387 tap_set_end_state(tap_get_state());
392 static int ftdi_execute_scan(struct jtag_command *cmd)
394 int retval = ERROR_OK;
396 DEBUG_JTAG_IO("%s type:%d", cmd->cmd.scan->ir_scan ? "IRSCAN" : "DRSCAN",
397 jtag_scan_type(cmd->cmd.scan));
399 /* Make sure there are no trailing fields with num_bits == 0, or the logic below will fail. */
400 while (cmd->cmd.scan->num_fields > 0
401 && cmd->cmd.scan->fields[cmd->cmd.scan->num_fields - 1].num_bits == 0) {
402 cmd->cmd.scan->num_fields--;
403 LOG_DEBUG("discarding trailing empty field");
406 if (cmd->cmd.scan->num_fields == 0) {
407 LOG_DEBUG("empty scan, doing nothing");
411 if (cmd->cmd.scan->ir_scan) {
412 if (tap_get_state() != TAP_IRSHIFT)
413 move_to_state(TAP_IRSHIFT);
415 if (tap_get_state() != TAP_DRSHIFT)
416 move_to_state(TAP_DRSHIFT);
419 ftdi_end_state(cmd->cmd.scan->end_state);
421 struct scan_field *field = cmd->cmd.scan->fields;
422 unsigned scan_size = 0;
424 for (int i = 0; i < cmd->cmd.scan->num_fields; i++, field++) {
425 scan_size += field->num_bits;
426 DEBUG_JTAG_IO("%s%s field %d/%d %d bits",
427 field->in_value ? "in" : "",
428 field->out_value ? "out" : "",
430 cmd->cmd.scan->num_fields,
433 if (i == cmd->cmd.scan->num_fields - 1 && tap_get_state() != tap_get_end_state()) {
434 /* Last field, and we're leaving IRSHIFT/DRSHIFT. Clock last bit during tap
435 * movement. This last field can't have length zero, it was checked above. */
436 mpsse_clock_data(mpsse_ctx,
443 uint8_t last_bit = 0;
444 if (field->out_value)
445 bit_copy(&last_bit, 0, field->out_value, field->num_bits - 1, 1);
446 uint8_t tms_bits = 0x01;
447 retval = mpsse_clock_tms_cs(mpsse_ctx,
455 tap_set_state(tap_state_transition(tap_get_state(), 1));
456 retval = mpsse_clock_tms_cs_out(mpsse_ctx,
462 tap_set_state(tap_state_transition(tap_get_state(), 0));
464 mpsse_clock_data(mpsse_ctx,
471 if (retval != ERROR_OK) {
472 LOG_ERROR("failed to add field %d in scan", i);
477 if (tap_get_state() != tap_get_end_state())
478 move_to_state(tap_get_end_state());
480 DEBUG_JTAG_IO("%s scan, %i bits, end in %s",
481 (cmd->cmd.scan->ir_scan) ? "IR" : "DR", scan_size,
482 tap_state_name(tap_get_end_state()));
487 static int ftdi_execute_reset(struct jtag_command *cmd)
489 DEBUG_JTAG_IO("reset trst: %i srst %i",
490 cmd->cmd.reset->trst, cmd->cmd.reset->srst);
492 if (cmd->cmd.reset->trst == 1
493 || (cmd->cmd.reset->srst
494 && (jtag_get_reset_config() & RESET_SRST_PULLS_TRST)))
495 tap_set_state(TAP_RESET);
497 struct signal *trst = find_signal_by_name("nTRST");
498 if (trst && cmd->cmd.reset->trst == 1) {
499 ftdi_set_signal(trst, '0');
500 } else if (trst && cmd->cmd.reset->trst == 0) {
501 if (jtag_get_reset_config() & RESET_TRST_OPEN_DRAIN)
502 ftdi_set_signal(trst, 'z');
504 ftdi_set_signal(trst, '1');
507 struct signal *srst = find_signal_by_name("nSRST");
508 if (srst && cmd->cmd.reset->srst == 1) {
509 ftdi_set_signal(srst, '0');
510 } else if (srst && cmd->cmd.reset->srst == 0) {
511 if (jtag_get_reset_config() & RESET_SRST_PUSH_PULL)
512 ftdi_set_signal(srst, '1');
514 ftdi_set_signal(srst, 'z');
517 DEBUG_JTAG_IO("trst: %i, srst: %i",
518 cmd->cmd.reset->trst, cmd->cmd.reset->srst);
522 static int ftdi_execute_sleep(struct jtag_command *cmd)
524 int retval = ERROR_OK;
526 DEBUG_JTAG_IO("sleep %" PRIi32, cmd->cmd.sleep->us);
528 retval = mpsse_flush(mpsse_ctx);
529 jtag_sleep(cmd->cmd.sleep->us);
530 DEBUG_JTAG_IO("sleep %" PRIi32 " usec while in %s",
532 tap_state_name(tap_get_state()));
536 static int ftdi_execute_stableclocks(struct jtag_command *cmd)
538 int retval = ERROR_OK;
540 /* this is only allowed while in a stable state. A check for a stable
541 * state was done in jtag_add_clocks()
543 int num_cycles = cmd->cmd.stableclocks->num_cycles;
545 /* 7 bits of either ones or zeros. */
546 uint8_t tms = tap_get_state() == TAP_RESET ? 0x7f : 0x00;
548 /* TODO: Use mpsse_clock_data with in=out=0 for this, if TMS can be set to
549 * the correct level and remain there during the scan */
550 while (num_cycles > 0 && retval == ERROR_OK) {
551 /* there are no state transitions in this code, so omit state tracking */
552 unsigned this_len = num_cycles > 7 ? 7 : num_cycles;
553 retval = mpsse_clock_tms_cs_out(mpsse_ctx, &tms, 0, this_len, false, JTAG_MODE);
554 num_cycles -= this_len;
557 DEBUG_JTAG_IO("clocks %i while in %s",
558 cmd->cmd.stableclocks->num_cycles,
559 tap_state_name(tap_get_state()));
563 static int ftdi_execute_command(struct jtag_command *cmd)
569 retval = ftdi_execute_reset(cmd);
572 retval = ftdi_execute_runtest(cmd);
575 retval = ftdi_execute_statemove(cmd);
578 retval = ftdi_execute_pathmove(cmd);
581 retval = ftdi_execute_scan(cmd);
584 retval = ftdi_execute_sleep(cmd);
586 case JTAG_STABLECLOCKS:
587 retval = ftdi_execute_stableclocks(cmd);
590 retval = ftdi_execute_tms(cmd);
593 LOG_ERROR("BUG: unknown JTAG command type encountered: %d", cmd->type);
594 retval = ERROR_JTAG_QUEUE_FAILED;
600 static int ftdi_execute_queue(void)
602 int retval = ERROR_OK;
604 /* blink, if the current layout has that feature */
605 struct signal *led = find_signal_by_name("LED");
607 ftdi_set_signal(led, '1');
609 for (struct jtag_command *cmd = jtag_command_queue; cmd; cmd = cmd->next) {
610 /* fill the write buffer with the desired command */
611 if (ftdi_execute_command(cmd) != ERROR_OK)
612 retval = ERROR_JTAG_QUEUE_FAILED;
616 ftdi_set_signal(led, '0');
618 retval = mpsse_flush(mpsse_ctx);
619 if (retval != ERROR_OK)
620 LOG_ERROR("error while flushing MPSSE queue: %d", retval);
625 static int ftdi_initialize(void)
629 if (tap_get_tms_path_len(TAP_IRPAUSE, TAP_IRPAUSE) == 7)
630 LOG_DEBUG("ftdi interface using 7 step jtag state transitions");
632 LOG_DEBUG("ftdi interface using shortest path jtag state transitions");
634 for (int i = 0; ftdi_vid[i] || ftdi_pid[i]; i++) {
635 mpsse_ctx = mpsse_open(&ftdi_vid[i], &ftdi_pid[i], ftdi_device_desc,
636 ftdi_serial, ftdi_channel);
642 return ERROR_JTAG_INIT_FAILED;
644 retval = mpsse_set_data_bits_low_byte(mpsse_ctx, output & 0xff, direction & 0xff);
645 if (retval == ERROR_OK)
646 retval = mpsse_set_data_bits_high_byte(mpsse_ctx, output >> 8, direction >> 8);
647 if (retval != ERROR_OK) {
648 LOG_ERROR("couldn't initialize FTDI with configured layout");
649 return ERROR_JTAG_INIT_FAILED;
652 retval = mpsse_loopback_config(mpsse_ctx, false);
653 if (retval != ERROR_OK) {
654 LOG_ERROR("couldn't write to FTDI to disable loopback");
655 return ERROR_JTAG_INIT_FAILED;
658 return mpsse_flush(mpsse_ctx);
661 static int ftdi_quit(void)
663 mpsse_close(mpsse_ctx);
668 COMMAND_HANDLER(ftdi_handle_device_desc_command)
671 if (ftdi_device_desc)
672 free(ftdi_device_desc);
673 ftdi_device_desc = strdup(CMD_ARGV[0]);
675 LOG_ERROR("expected exactly one argument to ftdi_device_desc <description>");
681 COMMAND_HANDLER(ftdi_handle_serial_command)
686 ftdi_serial = strdup(CMD_ARGV[0]);
688 return ERROR_COMMAND_SYNTAX_ERROR;
694 COMMAND_HANDLER(ftdi_handle_channel_command)
697 COMMAND_PARSE_NUMBER(u8, CMD_ARGV[0], ftdi_channel);
699 return ERROR_COMMAND_SYNTAX_ERROR;
704 COMMAND_HANDLER(ftdi_handle_layout_init_command)
707 return ERROR_COMMAND_SYNTAX_ERROR;
709 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[0], output);
710 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[1], direction);
715 COMMAND_HANDLER(ftdi_handle_layout_signal_command)
718 return ERROR_COMMAND_SYNTAX_ERROR;
720 bool invert_data = false;
721 uint16_t data_mask = 0;
722 bool invert_oe = false;
723 uint16_t oe_mask = 0;
724 for (unsigned i = 1; i < CMD_ARGC; i += 2) {
725 if (strcmp("-data", CMD_ARGV[i]) == 0) {
727 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i + 1], data_mask);
728 } else if (strcmp("-ndata", CMD_ARGV[i]) == 0) {
730 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i + 1], data_mask);
731 } else if (strcmp("-oe", CMD_ARGV[i]) == 0) {
733 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i + 1], oe_mask);
734 } else if (strcmp("-noe", CMD_ARGV[i]) == 0) {
736 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i + 1], oe_mask);
738 LOG_ERROR("unknown option '%s'", CMD_ARGV[i]);
739 return ERROR_COMMAND_SYNTAX_ERROR;
744 sig = find_signal_by_name(CMD_ARGV[0]);
746 sig = create_signal(CMD_ARGV[0]);
748 LOG_ERROR("failed to create signal %s", CMD_ARGV[0]);
752 sig->invert_data = invert_data;
753 sig->data_mask = data_mask;
754 sig->invert_oe = invert_oe;
755 sig->oe_mask = oe_mask;
760 COMMAND_HANDLER(ftdi_handle_set_signal_command)
763 return ERROR_COMMAND_SYNTAX_ERROR;
766 sig = find_signal_by_name(CMD_ARGV[0]);
768 LOG_ERROR("interface configuration doesn't define signal '%s'", CMD_ARGV[0]);
772 switch (*CMD_ARGV[1]) {
777 /* single character level specifier only */
778 if (CMD_ARGV[1][1] == '\0') {
779 ftdi_set_signal(sig, *CMD_ARGV[1]);
783 LOG_ERROR("unknown signal level '%s', use 0, 1 or z", CMD_ARGV[1]);
784 return ERROR_COMMAND_SYNTAX_ERROR;
787 return mpsse_flush(mpsse_ctx);
790 COMMAND_HANDLER(ftdi_handle_vid_pid_command)
792 if (CMD_ARGC > MAX_USB_IDS * 2) {
793 LOG_WARNING("ignoring extra IDs in ftdi_vid_pid "
794 "(maximum is %d pairs)", MAX_USB_IDS);
795 CMD_ARGC = MAX_USB_IDS * 2;
797 if (CMD_ARGC < 2 || (CMD_ARGC & 1)) {
798 LOG_WARNING("incomplete ftdi_vid_pid configuration directive");
800 return ERROR_COMMAND_SYNTAX_ERROR;
801 /* remove the incomplete trailing id */
806 for (i = 0; i < CMD_ARGC; i += 2) {
807 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i], ftdi_vid[i >> 1]);
808 COMMAND_PARSE_NUMBER(u16, CMD_ARGV[i + 1], ftdi_pid[i >> 1]);
812 * Explicitly terminate, in case there are multiples instances of
815 ftdi_vid[i >> 1] = ftdi_pid[i >> 1] = 0;
820 static const struct command_registration ftdi_command_handlers[] = {
822 .name = "ftdi_device_desc",
823 .handler = &ftdi_handle_device_desc_command,
824 .mode = COMMAND_CONFIG,
825 .help = "set the USB device description of the FTDI device",
826 .usage = "description_string",
829 .name = "ftdi_serial",
830 .handler = &ftdi_handle_serial_command,
831 .mode = COMMAND_CONFIG,
832 .help = "set the serial number of the FTDI device",
833 .usage = "serial_string",
836 .name = "ftdi_channel",
837 .handler = &ftdi_handle_channel_command,
838 .mode = COMMAND_CONFIG,
839 .help = "set the channel of the FTDI device that is used as JTAG",
843 .name = "ftdi_layout_init",
844 .handler = &ftdi_handle_layout_init_command,
845 .mode = COMMAND_CONFIG,
846 .help = "initialize the FTDI GPIO signals used "
847 "to control output-enables and reset signals",
848 .usage = "data direction",
851 .name = "ftdi_layout_signal",
852 .handler = &ftdi_handle_layout_signal_command,
854 .help = "define a signal controlled by one or more FTDI GPIO as data "
855 "and/or output enable",
856 .usage = "name [-data mask|-ndata mask] [-oe mask|-noe mask]",
859 .name = "ftdi_set_signal",
860 .handler = &ftdi_handle_set_signal_command,
861 .mode = COMMAND_EXEC,
862 .help = "control a layout-specific signal",
863 .usage = "name (1|0|z)",
866 .name = "ftdi_vid_pid",
867 .handler = &ftdi_handle_vid_pid_command,
868 .mode = COMMAND_CONFIG,
869 .help = "the vendor ID and product ID of the FTDI device",
870 .usage = "(vid pid)* ",
872 COMMAND_REGISTRATION_DONE
875 struct jtag_interface ftdi_interface = {
877 .supported = DEBUG_CAP_TMS_SEQ,
878 .commands = ftdi_command_handlers,
879 .transports = jtag_only,
881 .init = ftdi_initialize,
884 .speed_div = ftdi_speed_div,
886 .execute_queue = ftdi_execute_queue,