/*
* -------------------------------------------
- * MSP432 DriverLib - v01_04_00_18
+ * MSP432 DriverLib - v3_10_00_09
* -------------------------------------------
*
* --COPYRIGHT--,BSD,BSD
- * Copyright (c) 2015, Texas Instruments Incorporated
+ * Copyright (c) 2014, Texas Instruments Incorporated
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
// Control specific variables
//
//*****************************************************************************
-#define PSS_KEY_VALUE 0x0000695A
+#define PSS_KEY_VALUE PSS_KEY_KEY_VAL
-#define PSS_SVSMH SVSMHIE
+#define PSS_SVSMH PSS_IE_SVSMHIE
#define PSS_FULL_PERFORMANCE_MODE 0x01
#define PSS_NORMAL_PERFORMANCE_MODE 0x00
//*****************************************************************************
//
-//! Enables low side voltage supervisor/monitor.
+//! Enables the power supply system interrupt source.
//!
//! \return None.
//
//*****************************************************************************
-extern void PSS_enableLowSide(void);
+extern void PSS_enableInterrupt(void);
//*****************************************************************************
//
-//! Disables low side voltage supervisor/monitor.
+//! Disables the power supply system interrupt source.
//!
//! \return None.
//
//*****************************************************************************
-extern void PSS_disableLowSide(void);
+extern void PSS_disableInterrupt(void);
//*****************************************************************************
//
-//! Sets the performance mode of the high side regulator. Full performance
-//! mode allows for the best response times while normal performance mode is
-//! optimized for the lowest possible current consumption.
+//! Gets the current interrupt status.
//!
-//! \param ui8PowerMode is the performance mode to set. Valid values are one of
-//! the following:
-//! - \b PSS_FULL_PERFORMANCE_MODE,
-//! - \b PSS_NORMAL_PERFORMANCE_MODE
+//! \return The current interrupt status ( \b PSS_SVSMH )
//!
-//! \return None.
-//
-//*****************************************************************************
-extern void PSS_setLowSidePerformanceMode(uint_fast8_t ui8PowerMode);
-
//*****************************************************************************
-//
-//! Gets the performance mode of the low side voltage regulator. Refer to the
-//! user's guide for specific information about information about the different
-//! performance modes.
-//!
-//! \return Performance mode of the voltage regulator
-//
-//*****************************************************************************
-extern uint_fast8_t PSS_getLowSidePerformanceMode(void);
+extern uint32_t PSS_getInterruptStatus(void);
//*****************************************************************************
//
-//! Enables the power supply system interrupt source.
+//! Clears power supply system interrupt source.
//!
//! \return None.
//
//*****************************************************************************
-extern void PSS_enableInterrupt(void);
+extern void PSS_clearInterruptFlag(void);
+
//*****************************************************************************
//
-//! Disables the power supply system interrupt source.
+//! Enables the "forced" mode of the DCDC regulator. In this mode, the fail
+//! safe mechanism that disables the regulator to LDO mode when the supply
+//! voltage falls below the minimum supply voltage required for DCDC operation
+//! is turned off.
//!
//! \return None.
//
//*****************************************************************************
-extern void PSS_disableInterrupt(void);
+extern void PSS_enableForcedDCDCOperation(void);
-//*****************************************************************************
-//
-//! Gets the current interrupt status.
-//!
-//! \return The current interrupt status ( \b PSS_SVSMH )
-//!
-//*****************************************************************************
-extern uint32_t PSS_getInterruptStatus(void);
//*****************************************************************************
//
-//! Clears power supply system interrupt source.
+//! Disables the "forced" mode of the DCDC regulator. In this mode, the fail
+//! safe mechanism that disables the regulator to LDO mode when the supply
+//! voltage falls below the minimum supply voltage required for DCDC operation
+//! is turned on.
//!
//! \return None.
//
//*****************************************************************************
-extern void PSS_clearInterruptFlag(void);
+extern void PSS_disableForcedDCDCOperation(void);
//*****************************************************************************
//