--- /dev/null
+/***********************************************************************************************************************\r
+* DISCLAIMER\r
+* This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products. No \r
+* other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all \r
+* applicable laws, including copyright laws. \r
+* THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING\r
+* THIS SOFTWARE, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, \r
+* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. TO THE MAXIMUM \r
+* EXTENT PERMITTED NOT PROHIBITED BY LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES \r
+* SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS \r
+* SOFTWARE, EVEN IF RENESAS OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.\r
+* Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability of \r
+* this software. By using this software, you agree to the additional terms and conditions found by accessing the \r
+* following link:\r
+* http://www.renesas.com/disclaimer \r
+*\r
+* Copyright (C) 2012 Renesas Electronics Corporation. All rights reserved. \r
+***********************************************************************************************************************/\r
+/***********************************************************************************************************************\r
+* File Name : r_bsp_config_reference.c\r
+* Device(s) : RX63x\r
+* Description : The file r_bsp_config.h is used to configure your BSP. r_bsp_config.h should be included\r
+* somewhere in your package so that the r_bsp code has access to it. This file (r_bsp_config_reference.h)\r
+* is just a reference file that the user can use to make their own r_bsp_config.h file.\r
+************************************************************************************************************************\r
+* History : DD.MM.YYYY Version Description \r
+* : 13.03.2012 1.00 First Release \r
+***********************************************************************************************************************/\r
+#ifndef R_BSP_CONFIG_REF_HEADER_FILE\r
+#define R_BSP_CONFIG_REF_HEADER_FILE\r
+\r
+/***********************************************************************************************************************\r
+Configuration Options\r
+***********************************************************************************************************************/\r
+/* The 'BSP_DECLARE_STACK' macro is checked so that the stack is only declared in one place (resetprg.c). Every time a \r
+ '#pragma stacksize' is encountered, the stack size is increased. This prevents multiplication of stack size. */\r
+#if defined(BSP_DECLARE_STACK)\r
+/* User Stack size in bytes. The Renesas RX toolchain sets the stack size using the #pragma stacksize directive. */\r
+#pragma stacksize su=0x1000\r
+/* Interrupt Stack size in bytes. The Renesas RX toolchain sets the stack size using the #pragma stacksize directive. */\r
+#pragma stacksize si=0x400\r
+#endif\r
+\r
+/* Heap size in bytes. */\r
+#define HEAP_BYTES (0x4)\r
+\r
+/* After reset MCU will operate in Supervisor mode. To switch to User mode, set this macro to '1'. For more information\r
+ on the differences between these 2 modes see the CPU >> Processor Mode section of your MCU's hardware manual.\r
+ 0 = Stay in Supervisor mode.\r
+ 1 = Switch to User mode.\r
+*/\r
+#define RUN_IN_USER_MODE (0)\r
+\r
+/* To get into User Boot Mode the user must control some pins on the MCU and also set some values in ROM. These values\r
+ in ROM are described in the Option-Setting Memory section of the hardware manual. This macro sets these values so \r
+ that User Boot Mode can be used. The user is still responsible for setting the MCU pins appropriately.\r
+ 0 = Single-Chip or USB Boot Mode\r
+ 1 = User Boot Mode\r
+*/\r
+#define USER_BOOT_ENABLE (0)\r
+\r
+/* Set your desired ID code. NOTE, leave at the default (all 0xFF's) if you do not wish to use an ID code. If you set \r
+ this value and program it into the MCU then you will need to remember the ID code because the debugger will ask for \r
+ it when trying to connect. Note that the E1/E20 will ignore the ID code when programming the MCU during debugging.\r
+ If you set this value and then forget it then you can clear the ID code by connecting up in serial boot mode using \r
+ FDT. The ID Code is 16 bytes long. The macro below define the ID Code in 4-byte sections. */\r
+/* Lowest 4-byte section, address 0xFFFFFFA0. From MSB to LSB: Control Code, ID code 1, ID code 2, ID code 3. */\r
+#define ID_CODE_LONG_1 (0xFFFFFFFF)\r
+/* 2nd ID Code section, address 0xFFFFFFA4. From MSB to LSB: ID code 4, ID code 5, ID code 6, ID code 7. */\r
+#define ID_CODE_LONG_2 (0xFFFFFFFF)\r
+/* 3rd ID Code section, address 0xFFFFFFA8. From MSB to LSB: ID code 8, ID code 9, ID code 10, ID code 11. */\r
+#define ID_CODE_LONG_3 (0xFFFFFFFF)\r
+/* 4th ID Code section, address 0xFFFFFFAC. From MSB to LSB: ID code 12, ID code 13, ID code 14, ID code 15. */\r
+#define ID_CODE_LONG_4 (0xFFFFFFFF)\r
+\r
+/* This macro lets other modules no if a RTOS is being used.\r
+ 0 = RTOS is not used. \r
+ 1 = RTOS is used.\r
+*/\r
+#define RTOS_USED (0)\r
+\r
+/* Clock source select (CKSEL).\r
+ 0 = Low Speed On-Chip Oscillator (LOCO)\r
+ 1 = High Speed On-Chip Oscillator (HOCO)\r
+ 2 = Main Clock Oscillator \r
+ 3 = Sub-Clock Oscillator\r
+ 4 = PLL Circuit\r
+*/ \r
+#define CLOCK_SOURCE (4)\r
+\r
+/* Clock configuration options.\r
+ The input clock frequency is specified and then the system clocks are set by specifying the multipliers used. The\r
+ multiplier settings are used to set the clock registers in resetprg.c. If a 12MHz clock is used and the \r
+ ICLK is 96MHz, PCLKA is 48MHz, PCLKB is 48MHz, FCLK is 48MHz, USB Clock is 48MHz, and BCLK is 12MHz then the \r
+ settings would be:\r
+\r
+ XTAL_HZ = 12000000\r
+ PLL_DIV = 1 (no division)\r
+ PLL_MUL = 16 (12MHz x 16 = 192MHz)\r
+ ICK_DIV = 2 : System Clock (ICLK) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / ICK_DIV) = 96MHz\r
+ PCKA_DIV = 4 : Peripheral Clock A (PCLKA) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / PCKA_DIV) = 48MHz\r
+ PCKB_DIV = 4 : Peripheral Clock B (PCLKB) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / PCKB_DIV) = 48MHz\r
+ FCK_DIV = 4 : Flash IF Clock (FCLK) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / FCK_DIV) = 48MHz\r
+ BCK_DIV = 8 : External Bus Clock (BCK) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / BCK_DIV) = 24MHz\r
+ UCK_DIV = 4 : USB Clock (UCLK) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / UCK_DIV) = 48MHz\r
+*/\r
+/* XTAL - Input clock frequency in Hz */\r
+#define XTAL_HZ (12000000)\r
+/* PLL Input Frequency Divider Select (PLIDIV). \r
+ Available divisors = /1 (no division), /2, /4\r
+*/\r
+#define PLL_DIV (1)\r
+/* PLL Frequency Multiplication Factor Select (STC). \r
+ Available multipliers = x8, x10, x12, x16, x20, x24, x25, x50\r
+*/\r
+#define PLL_MUL (16)\r
+/* System Clock Divider (ICK).\r
+ Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64\r
+*/\r
+#define ICK_DIV (2)\r
+/* Peripheral Module Clock A Divider (PCKA). \r
+ Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64\r
+*/\r
+#define PCKA_DIV (4)\r
+/* Peripheral Module Clock B Divider (PCKB). \r
+ Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64\r
+*/\r
+#define PCKB_DIV (4)\r
+/* External Bus Clock Divider (BCK). \r
+ Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64\r
+*/\r
+#define BCK_DIV (8)\r
+/* Flash IF Clock Divider (FCK). \r
+ Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64\r
+*/\r
+#define FCK_DIV (4)\r
+/* IEBUS Clock Divider Select. \r
+ Available divisors = /1 (no division), /2, /4, /6, /8, /16, /32, /64\r
+*/\r
+#define IEBCK_DIV (8)\r
+/* USB Clock Divider Select. \r
+ Available divisors = /3, /4\r
+*/\r
+#define UCK_DIV (4)\r
+\r
+#endif /* R_BSP_CONFIG_REF_HEADER_FILE */\r
+\r
+\r
+\r
projects / freertos / blobdiff