#
-# (C) Copyright 2000 - 2008
+# (C) Copyright 2000 - 2009
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
Versioning:
===========
-U-Boot uses a 3 level version number containing a version, a
-sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
-sub-version "34", and patchlevel "4".
+Starting with the release in October 2008, the names of the releases
+were changed from numerical release numbers without deeper meaning
+into a time stamp based numbering. Regular releases are identified by
+names consisting of the calendar year and month of the release date.
+Additional fields (if present) indicate release candidates or bug fix
+releases in "stable" maintenance trees.
-The patchlevel is used to indicate certain stages of development
-between released versions, i. e. officially released versions of
-U-Boot will always have a patchlevel of "0".
+Examples:
+ U-Boot v2009.11 - Release November 2009
+ U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
+ U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
Directory Hierarchy:
====================
-- board Board dependent files
-- common Misc architecture independent functions
-- cpu CPU specific files
- - 74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
- - arm720t Files specific to ARM 720 CPUs
- - arm920t Files specific to ARM 920 CPUs
- - at91rm9200 Files specific to Atmel AT91RM9200 CPU
- - imx Files specific to Freescale MC9328 i.MX CPUs
- - s3c24x0 Files specific to Samsung S3C24X0 CPUs
- - arm925t Files specific to ARM 925 CPUs
- - arm926ejs Files specific to ARM 926 CPUs
- - arm1136 Files specific to ARM 1136 CPUs
- - at32ap Files specific to Atmel AVR32 AP CPUs
- - blackfin Files specific to Analog Devices Blackfin CPUs
- - i386 Files specific to i386 CPUs
- - ixp Files specific to Intel XScale IXP CPUs
- - leon2 Files specific to Gaisler LEON2 SPARC CPU
- - leon3 Files specific to Gaisler LEON3 SPARC CPU
- - mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
- - mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
- - mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
- - mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
- - mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
- - mips Files specific to MIPS CPUs
- - mpc5xx Files specific to Freescale MPC5xx CPUs
- - mpc5xxx Files specific to Freescale MPC5xxx CPUs
- - mpc8xx Files specific to Freescale MPC8xx CPUs
- - mpc8220 Files specific to Freescale MPC8220 CPUs
- - mpc824x Files specific to Freescale MPC824x CPUs
- - mpc8260 Files specific to Freescale MPC8260 CPUs
- - mpc85xx Files specific to Freescale MPC85xx CPUs
- - nios Files specific to Altera NIOS CPUs
- - nios2 Files specific to Altera Nios-II CPUs
- - ppc4xx Files specific to AMCC PowerPC 4xx CPUs
- - pxa Files specific to Intel XScale PXA CPUs
- - s3c44b0 Files specific to Samsung S3C44B0 CPUs
- - sa1100 Files specific to Intel StrongARM SA1100 CPUs
-- disk Code for disk drive partition handling
-- doc Documentation (don't expect too much)
-- drivers Commonly used device drivers
-- dtt Digital Thermometer and Thermostat drivers
-- examples Example code for standalone applications, etc.
-- include Header Files
-- lib_arm Files generic to ARM architecture
-- lib_avr32 Files generic to AVR32 architecture
-- lib_blackfin Files generic to Blackfin architecture
-- lib_generic Files generic to all architectures
-- lib_i386 Files generic to i386 architecture
-- lib_m68k Files generic to m68k architecture
-- lib_mips Files generic to MIPS architecture
-- lib_nios Files generic to NIOS architecture
-- lib_ppc Files generic to PowerPC architecture
-- lib_sparc Files generic to SPARC architecture
-- libfdt Library files to support flattened device trees
-- net Networking code
-- post Power On Self Test
-- rtc Real Time Clock drivers
-- tools Tools to build S-Record or U-Boot images, etc.
+/arch Architecture specific files
+ /arm Files generic to ARM architecture
+ /cpu CPU specific files
+ /arm720t Files specific to ARM 720 CPUs
+ /arm920t Files specific to ARM 920 CPUs
+ /at91rm9200 Files specific to Atmel AT91RM9200 CPU
+ /imx Files specific to Freescale MC9328 i.MX CPUs
+ /s3c24x0 Files specific to Samsung S3C24X0 CPUs
+ /arm925t Files specific to ARM 925 CPUs
+ /arm926ejs Files specific to ARM 926 CPUs
+ /arm1136 Files specific to ARM 1136 CPUs
+ /ixp Files specific to Intel XScale IXP CPUs
+ /pxa Files specific to Intel XScale PXA CPUs
+ /s3c44b0 Files specific to Samsung S3C44B0 CPUs
+ /sa1100 Files specific to Intel StrongARM SA1100 CPUs
+ /lib Architecture specific library files
+ /avr32 Files generic to AVR32 architecture
+ /cpu CPU specific files
+ /lib Architecture specific library files
+ /blackfin Files generic to Analog Devices Blackfin architecture
+ /cpu CPU specific files
+ /lib Architecture specific library files
+ /i386 Files generic to i386 architecture
+ /cpu CPU specific files
+ /lib Architecture specific library files
+ /m68k Files generic to m68k architecture
+ /cpu CPU specific files
+ /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
+ /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
+ /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
+ /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
+ /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
+ /lib Architecture specific library files
+ /microblaze Files generic to microblaze architecture
+ /cpu CPU specific files
+ /lib Architecture specific library files
+ /mips Files generic to MIPS architecture
+ /cpu CPU specific files
+ /lib Architecture specific library files
+ /nios2 Files generic to Altera NIOS2 architecture
+ /cpu CPU specific files
+ /lib Architecture specific library files
+ /powerpc Files generic to PowerPC architecture
+ /cpu CPU specific files
+ /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
+ /mpc5xx Files specific to Freescale MPC5xx CPUs
+ /mpc5xxx Files specific to Freescale MPC5xxx CPUs
+ /mpc8xx Files specific to Freescale MPC8xx CPUs
+ /mpc8220 Files specific to Freescale MPC8220 CPUs
+ /mpc824x Files specific to Freescale MPC824x CPUs
+ /mpc8260 Files specific to Freescale MPC8260 CPUs
+ /mpc85xx Files specific to Freescale MPC85xx CPUs
+ /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
+ /lib Architecture specific library files
+ /sh Files generic to SH architecture
+ /cpu CPU specific files
+ /sh2 Files specific to sh2 CPUs
+ /sh3 Files specific to sh3 CPUs
+ /sh4 Files specific to sh4 CPUs
+ /lib Architecture specific library files
+ /sparc Files generic to SPARC architecture
+ /cpu CPU specific files
+ /leon2 Files specific to Gaisler LEON2 SPARC CPU
+ /leon3 Files specific to Gaisler LEON3 SPARC CPU
+ /lib Architecture specific library files
+/api Machine/arch independent API for external apps
+/board Board dependent files
+/common Misc architecture independent functions
+/disk Code for disk drive partition handling
+/doc Documentation (don't expect too much)
+/drivers Commonly used device drivers
+/examples Example code for standalone applications, etc.
+/fs Filesystem code (cramfs, ext2, jffs2, etc.)
+/include Header Files
+/lib Files generic to all architectures
+ /libfdt Library files to support flattened device trees
+ /lzma Library files to support LZMA decompression
+ /lzo Library files to support LZO decompression
+/net Networking code
+/post Power On Self Test
+/rtc Real Time Clock drivers
+/tools Tools to build S-Record or U-Boot images, etc.
Software Configuration:
=======================
This define fills in the correct boot CPU in the boot
param header, the default value is zero if undefined.
+ CONFIG_OF_IDE_FIXUP
+
+ U-Boot can detect if an IDE device is present or not.
+ If not, and this new config option is activated, U-Boot
+ removes the ATA node from the DTS before booting Linux,
+ so the Linux IDE driver does not probe the device and
+ crash. This is needed for buggy hardware (uc101) where
+ no pull down resistor is connected to the signal IDE5V_DD7.
+
- vxWorks boot parameters:
bootvx constructs a valid bootline using the following
must be defined, to setup the maximum idle timeout for
the SMC.
-- Interrupt driven serial port input:
- CONFIG_SERIAL_SOFTWARE_FIFO
-
- PPC405GP only.
- Use an interrupt handler for receiving data on the
- serial port. It also enables using hardware handshake
- (RTS/CTS) and UART's built-in FIFO. Set the number of
- bytes the interrupt driven input buffer should have.
-
- Leave undefined to disable this feature, including
- disable the buffer and hardware handshake.
-
-- Console UART Number:
- CONFIG_UART1_CONSOLE
-
- AMCC PPC4xx only.
- If defined internal UART1 (and not UART0) is used
- as default U-Boot console.
-
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
+ CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
CONFIG_CMD_SAVEENV saveenv
CONFIG_LBA48
Set this to enable support for disks larger than 137GB
- Also look at CONFIG_SYS_64BIT_LBA ,CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
+ Also look at CONFIG_SYS_64BIT_LBA.
Whithout these , LBA48 support uses 32bit variables and will 'only'
support disks up to 2.1TB.
- NETWORK Support (other):
+ CONFIG_DRIVER_AT91EMAC
+ Support for AT91RM9200 EMAC.
+
+ CONFIG_RMII
+ Define this to use reduced MII inteface
+
+ CONFIG_DRIVER_AT91EMAC_QUIET
+ If this defined, the driver is quiet.
+ The driver doen't show link status messages.
+
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
- CONFIG_DRIVER_SMC911X
+ CONFIG_SMC911X
Support for SMSC's LAN911x and LAN921x chips
- CONFIG_DRIVER_SMC911X_BASE
+ CONFIG_SMC911X_BASE
Define this to hold the physical address
of the device (I/O space)
- CONFIG_DRIVER_SMC911X_32_BIT
+ CONFIG_SMC911X_32_BIT
Define this if data bus is 32 bits
- CONFIG_DRIVER_SMC911X_16_BIT
+ CONFIG_SMC911X_16_BIT
Define this if data bus is 16 bits. If your processor
automatically converts one 32 bit word to two 16 bit
- words you may also try CONFIG_DRIVER_SMC911X_32_BIT.
+ words you may also try CONFIG_SMC911X_32_BIT.
- USB Support:
At the moment only the UHCI host controller is
images, gzipped BMP images can be displayed via the
splashscreen support or the bmp command.
+- Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
+
+ If this option is set, 8-bit RLE compressed BMP images
+ can be displayed via the splashscreen support or the
+ bmp command.
+
- Compression support:
CONFIG_BZIP2
to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
the CPU's i2c node address).
- Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
- sets the CPU up as a master node and so its address should
- therefore be cleared to 0 (See, eg, MPC823e User's Manual
- p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0.
+ Now, the u-boot i2c code for the mpc8xx
+ (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
+ and so its address should therefore be cleared to 0 (See,
+ eg, MPC823e User's Manual p.16-473). So, set
+ CONFIG_SYS_I2C_SLAVE to 0.
CONFIG_SYS_I2C_INIT_MPC5XXX
#define I2C_DELAY udelay(2)
+ CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
+
+ If your arch supports the generic GPIO framework (asm/gpio.h),
+ then you may alternatively define the two GPIOs that are to be
+ used as SCL / SDA. Any of the previous I2C_xxx macros will
+ have GPIO-based defaults assigned to them as appropriate.
+
+ You should define these to the GPIO value as given directly to
+ the generic GPIO functions.
+
CONFIG_SYS_I2C_INIT_BOARD
When a board is reset during an i2c bus transfer
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
+ CONFIG_SYS_I2C_BOARD_LATE_INIT
+
+ An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
+ defined a custom i2c_board_late_init() routine in
+ boards/xxx/board.c is run AFTER the operations in i2c_init()
+ is completed. This callpoint can be used to unreset i2c bus
+ using CPU i2c controller register accesses for CPUs whose i2c
+ controller provide such a method. It is called at the end of
+ i2c_init() to allow i2c_init operations to setup the i2c bus
+ controller on the CPU (e.g. setting bus speed & slave address).
+
CONFIG_I2CFAST (PPC405GP|PPC405EP only)
This option enables configuration of bi_iic_fast[] flags
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
-- Automatic software updates via TFTP server
- CONFIG_UPDATE_TFTP
- CONFIG_UPDATE_TFTP_CNT_MAX
- CONFIG_UPDATE_TFTP_MSEC_MAX
-
- These options enable and control the auto-update feature;
- for a more detailed description refer to doc/README.update.
-
-- MTD Support (mtdparts command, UBI support)
- CONFIG_MTD_DEVICE
-
- Adds the MTD device infrastructure from the Linux kernel.
- Needed for mtdparts command support.
-
- CONFIG_MTD_PARTITIONS
-
- Adds the MTD partitioning infrastructure from the Linux
- kernel. Needed for UBI support.
-
Legacy uImage format:
Arg Where When
13 common/image.c Start multifile image verification
14 common/image.c No initial ramdisk, no multifile, continue.
- 15 lib_<arch>/bootm.c All preparation done, transferring control to OS
+ 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
- -30 lib_ppc/board.c Fatal error, hang the system
+ -30 arch/powerpc/lib/board.c Fatal error, hang the system
-31 post/post.c POST test failed, detected by post_output_backlog()
-32 post/post.c POST test failed, detected by post_run_single()
-150 common/cmd_nand.c Incorrect FIT image format
151 common/cmd_nand.c FIT image format OK
+- Automatic software updates via TFTP server
+ CONFIG_UPDATE_TFTP
+ CONFIG_UPDATE_TFTP_CNT_MAX
+ CONFIG_UPDATE_TFTP_MSEC_MAX
+
+ These options enable and control the auto-update feature;
+ for a more detailed description refer to doc/README.update.
+
+- MTD Support (mtdparts command, UBI support)
+ CONFIG_MTD_DEVICE
+
+ Adds the MTD device infrastructure from the Linux kernel.
+ Needed for mtdparts command support.
+
+ CONFIG_MTD_PARTITIONS
+
+ Adds the MTD partitioning infrastructure from the Linux
+ kernel. Needed for UBI support.
+
Modem Support:
--------------
on high Ethernet traffic.
Defaults to 4 if not defined.
+- CONFIG_ENV_MAX_ENTRIES
+
+ Maximum number of entries in the hash table that is used
+ internally to store the environment settings. The default
+ setting is supposed to be generous and should work in most
+ cases. This setting can be used to tune behaviour; see
+ lib/hashtable.c for details.
+
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
following configurations:
- CONFIG_SYS_EEPROM_SIZE:
The size in bytes of the EEPROM device.
+ - CONFIG_ENV_EEPROM_IS_ON_I2C
+ define this, if you have I2C and SPI activated, and your
+ EEPROM, which holds the environment, is on the I2C bus.
+
+ - CONFIG_I2C_ENV_EEPROM_BUS
+ if you have an Environment on an EEPROM reached over
+ I2C muxes, you can define here, how to reach this
+ EEPROM. For example:
+
+ #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
+
+ EEPROM which holds the environment, is reached over
+ a pca9547 i2c mux with address 0x70, channel 3.
- CONFIG_ENV_IS_IN_DATAFLASH:
Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
-created; also, when using EEPROM you will have to use getenv_r()
+created; also, when using EEPROM you will have to use getenv_f()
until then to read environment variables.
The environment is protected by a CRC32 checksum. Before the monitor
- CONFIG_SYS_FAULT_MII_ADDR:
MII address of the PHY to check for the Ethernet link state.
-- CONFIG_SYS_64BIT_VSPRINTF:
- Makes vsprintf (and all *printf functions) support printing
- of 64bit values by using the L quantifier
-
-- CONFIG_SYS_64BIT_STRTOUL:
- Adds simple_strtoull that returns a 64bit value
-
- CONFIG_NS16550_MIN_FUNCTIONS:
Define this if you desire to only have use of the NS16550_init
and NS16550_putc functions for the serial driver located at
CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
- Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
+ Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
- CONFIG_PCI_DISABLE_PCIE:
Disable PCI-Express on systems where it is supported but not
working with an in-memory copy. In case the Flash area containing the
environment is erased by accident, a default environment is provided.
-Some configuration options can be set using Environment Variables:
+Some configuration options can be set using Environment Variables.
+
+List of environment variables (most likely not complete):
baudrate - see CONFIG_BAUDRATE
interface is currently active. For example you
can do the following
- => setenv ethact FEC ETHERNET
- => ping 192.168.0.1 # traffic sent on FEC ETHERNET
- => setenv ethact SCC ETHERNET
- => ping 10.0.0.1 # traffic sent on SCC ETHERNET
+ => setenv ethact FEC
+ => ping 192.168.0.1 # traffic sent on FEC
+ => setenv ethact SCC
+ => ping 10.0.0.1 # traffic sent on SCC
ethrotate - When set to "no" U-Boot does not go through all
available network interfaces.
It just stays at the currently selected interface.
- netretry - When set to "no" each network operation will
+ netretry - When set to "no" each network operation will
either succeed or fail without retrying.
When set to "once" the network operation will
fail when all the available network interfaces
tftpdstport - If this is set, the value is used for TFTP's UDP
destination port instead of the Well Know Port 69.
- vlan - When set to a value < 4095 the traffic over
+ tftpblocksize - Block size to use for TFTP transfers; if not set,
+ we use the TFTP server's default block size
+
+ tftptimeout - Retransmission timeout for TFTP packets (in milli-
+ seconds, minimum value is 1000 = 1 second). Defines
+ when a packet is considered to be lost so it has to
+ be retransmitted. The default is 5000 = 5 seconds.
+ Lowering this value may make downloads succeed
+ faster in networks with high packet loss rates or
+ with unreliable TFTP servers.
+
+ vlan - When set to a value < 4095 the traffic over
Ethernet is encapsulated/received over 802.1q
VLAN tagged frames.
o If neither SROM nor the environment contain a MAC address, an error
is raised.
+If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
+will be programmed into hardware as part of the initialization process. This
+may be skipped by setting the appropriate 'ethmacskip' environment variable.
+The naming convention is as follows:
+"ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
Image Formats:
==============
Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
INTEGRITY).
* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
- IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
- Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC).
+ IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
+ Currently supported: ARM, AVR32, Intel x86, MIPS, Nios II, PowerPC).
* Compression Type (uncompressed, gzip, bzip2)
* Load Address
* Entry Point
(no, we don't intend to provide a full virtual machine interface to
Linux :-).
-But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
+But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
Just make sure your machine specific header file (for instance
include/asm-ppc/tqm8xx.h) includes the same definition of the Board
-> tools/mkimage -n '2.4.4 kernel for TQM850L' \
> -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
- > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
+ > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
> examples/uImage.TQM850L
Image Name: 2.4.4 kernel for TQM850L
Created: Wed Jul 19 02:34:59 2000
needs more space in Flash, but boots much faster since it does not
need to be uncompressed:
- -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
+ -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
-> tools/mkimage -n '2.4.4 kernel for TQM850L' \
> -A ppc -O linux -T kernel -C none -a 0 -e 0 \
- > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
+ > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
> examples/uImage.TQM850L-uncompressed
Image Name: 2.4.4 kernel for TQM850L
Created: Wed Jul 19 02:34:59 2000
R30: GOT pointer
R31: frame pointer
- (U-Boot also uses R14 as internal GOT pointer.)
+ (U-Boot also uses R12 as internal GOT pointer. r12
+ is a volatile register so r12 needs to be reset when
+ going back and forth between asm and C)
==> U-Boot will use R2 to hold a pointer to the global data
==> U-Boot will use R8 to hold a pointer to the global data
+On Nios II, the ABI is documented here:
+ http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
+
+ ==> U-Boot will use gp to hold a pointer to the global data
+
+ Note: on Nios II, we give "-G0" option to gcc and don't use gp
+ to access small data sections, so gp is free.
+
NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
or current versions of GCC may "optimize" the code too much.