kernel configuration options. The intention is to make it easier to
build a config tool - later.
+- ARM Platform Bus Type(CCI):
+ CoreLink Cache Coherent Interconnect (CCI) is ARM BUS which
+ provides full cache coherency between two clusters of multi-core
+ CPUs and I/O coherency for devices and I/O masters
+
+ CONFIG_SYS_FSL_HAS_CCI400
+
+ Defined For SoC that has cache coherent interconnect
+ CCN-400
+
+ CONFIG_SYS_FSL_HAS_CCN504
+
+ Defined for SoC that has cache coherent interconnect CCN-504
The following options need to be configured:
supported, core will start to execute uboot when wakes up.
- Generic CPU options:
- CONFIG_SYS_GENERIC_GLOBAL_DATA
- Defines global data is initialized in generic board board_init_f().
- If this macro is defined, global data is created and cleared in
- generic board board_init_f(). Without this macro, architecture/board
- should initialize global data before calling board_init_f().
-
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Defines the endianess of the CPU. Implementation of those
binary in its image. This device tree file should be in the
board directory and called <soc>-<board>.dts. The binary file
is then picked up in board_init_f() and made available through
- the global data structure as gd->blob.
+ the global data structure as gd->fdt_blob.
CONFIG_OF_SEPARATE
If this variable is defined, U-Boot will build a device tree
control registers. This behavior won't affect the
correctnessof 10/100 link speed update.
- CONFIG_SMC911X
- Support for SMSC's LAN911x and LAN921x chips
-
- CONFIG_SMC911X_BASE
- Define this to hold the physical address
- of the device (I/O space)
-
- CONFIG_SMC911X_32_BIT
- Define this if data bus is 32 bits
-
- CONFIG_SMC911X_16_BIT
- Define this if data bus is 16 bits. If your processor
- automatically converts one 32 bit word to two 16 bit
- words you may also try CONFIG_SMC911X_32_BIT.
-
CONFIG_SH_ETHER
Support for Renesas on-chip Ethernet controller
entering dfuMANIFEST state. Host waits this timeout, before
sending again an USB request to the device.
-- USB Device Android Fastboot support:
- CONFIG_USB_FUNCTION_FASTBOOT
- This enables the USB part of the fastboot gadget
-
- CONFIG_ANDROID_BOOT_IMAGE
- This enables support for booting images which use the Android
- image format header.
-
- CONFIG_FASTBOOT_BUF_ADDR
- The fastboot protocol requires a large memory buffer for
- downloads. Define this to the starting RAM address to use for
- downloaded images.
-
- CONFIG_FASTBOOT_BUF_SIZE
- The fastboot protocol requires a large memory buffer for
- downloads. This buffer should be as large as possible for a
- platform. Define this to the size available RAM for fastboot.
-
- CONFIG_FASTBOOT_FLASH
- The fastboot protocol includes a "flash" command for writing
- the downloaded image to a non-volatile storage device. Define
- this to enable the "fastboot flash" command.
-
- CONFIG_FASTBOOT_FLASH_MMC_DEV
- The fastboot "flash" command requires additional information
- regarding the non-volatile storage device. Define this to
- the eMMC device that fastboot should use to store the image.
-
- CONFIG_FASTBOOT_GPT_NAME
- The fastboot "flash" command supports writing the downloaded
- image to the Protective MBR and the Primary GUID Partition
- Table. (Additionally, this downloaded image is post-processed
- to generate and write the Backup GUID Partition Table.)
- This occurs when the specified "partition name" on the
- "fastboot flash" command line matches this value.
- The default is "gpt" if undefined.
-
- CONFIG_FASTBOOT_MBR_NAME
- The fastboot "flash" command supports writing the downloaded
- image to DOS MBR.
- This occurs when the "partition name" specified on the
- "fastboot flash" command line matches this value.
- If not defined the default value "mbr" is used.
-
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND
Define these for a default partition on a NAND device
this is instead controlled by the value of
/config/load-environment.
-- DataFlash Support:
- CONFIG_HAS_DATAFLASH
-
- Defining this option enables DataFlash features and
- allows to read/write in Dataflash via the standard
- commands cp, md...
-
- Serial Flash support
Usage requires an initial 'sf probe' to define the serial
flash parameters, followed by read/write/erase/update
CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
the bootcounter.
CONFIG_BOOTCOUNT_ALEN = address len
+ CONFIG_BOOTCOUNT_EXT
+ enable support for the bootcounter in EXT filesystem
+ CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
+ and write.
+ CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
+ CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
+ CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
Define this if you need to first read the OOB and then the
data. This is used, for example, on davinci platforms.
- CONFIG_SPL_OMAP3_ID_NAND
- Support for an OMAP3-specific set of functions to return the
- ID and MFR of the first attached NAND chip, if present.
-
CONFIG_SPL_RAM_DEVICE
Support for running image already present in ram, in SPL binary
Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
-created; also, when using EEPROM you will have to use getenv_f()
+created; also, when using EEPROM you will have to use env_get_f()
until then to read environment variables.
The environment is protected by a CRC32 checksum. Before the monitor
Please see http://www.denx.de/wiki/U-Boot/Patches for details.
Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
-see http://lists.denx.de/mailman/listinfo/u-boot
+see https://lists.denx.de/listinfo/u-boot
When you send a patch, please include the following information with
it: