(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
- CONFIG_CMD_SHA1 print sha1 memory digest
+ CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
CONFIG_PCA953X_INFO - enable pca953x info command
+ The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
+ chip-ngpio pairs that tell the PCA953X driver the number of
+ pins supported by a particular chip.
+
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
+ CONFIG_FTGMAC100
+ Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
+
+ CONFIG_FTGMAC100_EGIGA
+ Define this to use GE link update with gigabit PHY.
+ Define this if FTGMAC100 is connected to gigabit PHY.
+ If your system has 10/100 PHY only, it might not occur
+ wrong behavior. Because PHY usually return timeout or
+ useless data when polling gigabit status and gigabit
+ control registers. This behavior won't affect the
+ correctnessof 10/100 link speed update.
+
CONFIG_SMC911X
Support for SMSC's LAN911x and LAN921x chips
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
+ CONFIG_SH_ETHER
+ Support for Renesas on-chip Ethernet controller
+
+ CONFIG_SH_ETHER_USE_PORT
+ Define the number of ports to be used
+
+ CONFIG_SH_ETHER_PHY_ADDR
+ Define the ETH PHY's address
+
+ CONFIG_SH_ETHER_CACHE_WRITEBACK
+ If this option is set, the driver enables cache flush.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
+ CONFIG_SH_SPI
+
+ Enables the driver for SPI controller on SuperH. Currently
+ only SH7757 is supported.
+
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
- CONFIG_ENV_MAX_ENTRIES
- Maximum number of entries in the hash table that is used
- internally to store the environment settings. The default
- setting is supposed to be generous and should work in most
- cases. This setting can be used to tune behaviour; see
- lib/hashtable.c for details.
+ Maximum number of entries in the hash table that is used
+ internally to store the environment settings. The default
+ setting is supposed to be generous and should work in most
+ cases. This setting can be used to tune behaviour; see
+ lib/hashtable.c for details.
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
data is located at the end of the available space
- (sometimes written as (CONFIG_SYS_INIT_RAM_END -
+ (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_GBL_DATA_OFFSET) downward.
Disable PCI-Express on systems where it is supported but not
required.
+- CONFIG_SYS_SRIO:
+ Chip has SRIO or not
+
+- CONFIG_SRIO1:
+ Board has SRIO 1 port available
+
+- CONFIG_SRIO2:
+ Board has SRIO 2 port available
+
+- CONFIG_SYS_SRIOn_MEM_VIRT:
+ Virtual Address of SRIO port 'n' memory region
+
+- CONFIG_SYS_SRIOn_MEM_PHYS:
+ Physical Address of SRIO port 'n' memory region
+
+- CONFIG_SYS_SRIOn_MEM_SIZE:
+ Size of SRIO port 'n' memory region
+
- CONFIG_SPD_EEPROM
Get DDR timing information from an I2C EEPROM. Common
with pluggable memory modules such as SODIMMs
globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT
-- CONFIG_SKIP_RELOCATE_UBOOT
+ [ARM only] If this variable is defined, then certain
+ low level initializations (like setting up the memory
+ controller) are omitted and/or U-Boot does not
+ relocate itself into RAM.
- [ARM only] If these variables are defined, then
- certain low level initializations (like setting up
- the memory controller) are omitted and/or U-Boot does
- not relocate itself into RAM.
- Normally these variables MUST NOT be defined. The
- only exception is when U-Boot is loaded (to RAM) by
- some other boot loader or by a debugger which
- performs these initializations itself.
+ Normally this variable MUST NOT be defined. The only
+ exception is when U-Boot is loaded (to RAM) by some
+ other boot loader or by a debugger which performs
+ these initializations itself.
- CONFIG_PRELOADER
-
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.