CONFIG_CMD_IMLS List all images found in NOR flash
CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
CONFIG_CMD_IMMAP * IMMR dump support
+ CONFIG_CMD_IOTRACE * I/O tracing for debugging
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
CONFIG_CMD_IRQ * irqinfo
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
+- I/O tracing:
+ When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
+ accesses and can checksum them or write a list of them out
+ to memory. See the 'iotrace' command for details. This is
+ useful for testing device drivers since it can confirm that
+ the driver behaves the same way before and after a code
+ change. Currently this is supported on sandbox and arm. To
+ add support for your architecture, add '#include <iotrace.h>'
+ to the bottom of arch/<arch>/include/asm/io.h and test.
+
+ Example output from the 'iotrace stats' command is below.
+ Note that if the trace buffer is exhausted, the checksum will
+ still continue to operate.
+
+ iotrace is enabled
+ Start: 10000000 (buffer start address)
+ Size: 00010000 (buffer size)
+ Offset: 00000120 (current buffer offset)
+ Output: 10000120 (start + offset)
+ Count: 00000018 (number of trace records)
+ CRC32: 9526fb66 (CRC32 of all trace records)
+
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
- CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
- interval for usb hub power-on delay.(minimum 100msec)
-
- USB Device:
Define the below if you wish to use the USB console.
Once firmware is rebuilt from a serial console issue the
window->master inbound window->master LAW->the ucode address in
master's memory space.
+Freescale Layerscape Management Complex Firmware Support:
+---------------------------------------------------------
+The Freescale Layerscape Management Complex (MC) supports the loading of
+"firmware".
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_FSL_MC_ENET
+ Enable the MC driver for Layerscape SoCs.
+
+- CONFIG_SYS_LS_MC_FW_ADDR
+ The address in the storage device where the firmware is located. The
+ meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_LS_MC_FW_LENGTH
+ The maximum possible size of the firmware. The firmware binary format
+ has a field that specifies the actual size of the firmware, but it
+ might not be possible to read any part of the firmware unless some
+ local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_LS_MC_FW_IN_NOR
+ Specifies that MC firmware is located in NOR flash, mapped as
+ normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
+ virtual address in NOR flash.
+
Building the Software:
======================
and make sure that your definition of IMAP_ADDR uses the same value
as your U-Boot configuration in CONFIG_SYS_IMMR.
+Note that U-Boot now has a driver model, a unified model for drivers.
+If you are adding a new driver, plumb it into driver model. If there
+is no uclass available, you are encouraged to create one. See
+doc/driver-model.
+
Configuring the Linux kernel:
-----------------------------