/mpc5xx Files specific to Freescale MPC5xx CPUs
/mpc5xxx Files specific to Freescale MPC5xxx CPUs
/mpc8xx Files specific to Freescale MPC8xx CPUs
- /mpc8220 Files specific to Freescale MPC8220 CPUs
/mpc824x Files specific to Freescale MPC824x CPUs
/mpc8260 Files specific to Freescale MPC8260 CPUs
/mpc85xx Files specific to Freescale MPC85xx CPUs
See Freescale App Note 4493 for more information about
this erratum.
+ CONFIG_A003399_NOR_WORKAROUND
+ Enables a workaround for IFC erratum A003399. It is only
+ requred during NOR boot.
+
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
This is the value to write into CCSR offset 0x18600
according to the A004510 workaround.
+ CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
+ This value denotes start offset of M2 memory
+ which is directly connected to the DSP core.
+
+ CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
+ This value denotes start offset of DSP CCSR space.
+
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
+ CONFIG_CMD_FUSE Device fuse support
CONFIG_CMD_GETTIME * Get time since boot
CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_GREPENV * search environment
If this option is set, the driver enables cache flush.
- TPM Support:
- CONFIG_GENERIC_LPC_TPM
+ CONFIG_TPM
+ Support TPM devices.
+
+ CONFIG_TPM_TIS_I2C
+ Support for i2c bus TPM devices. Only one device
+ per system is supported at this time.
+
+ CONFIG_TPM_TIS_I2C_BUS_NUMBER
+ Define the the i2c bus number for the TPM device
+
+ CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
+ Define the TPM's address on the i2c bus
+
+ CONFIG_TPM_TIS_I2C_BURST_LIMITATION
+ Define the burst count bytes upper limit
+
+ CONFIG_TPM_TIS_LPC
Support for generic parallel port TPM devices. Only one device
per system is supported at this time.
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
+ CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
+ interval for usb hub power-on delay.(minimum 100msec)
+
- USB Device:
Define the below if you wish to use the USB console.
Once firmware is rebuilt from a serial console issue the
Export function i8042_kbd_init, i8042_tstc and i8042_getc
for cfb_console. Supports cursor blinking.
+ CONFIG_CROS_EC_KEYB
+ Enables a Chrome OS keyboard using the CROS_EC interface.
+ This uses CROS_EC to communicate with a second microcontroller
+ which provides key scans on request.
+
- Video support:
CONFIG_VIDEO
Define this option to include a destructive SPI flash
test ('sf test').
+ CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
+
+ Define this option to use the Bank addr/Extended addr
+ support on SPI flashes which has size > 16Mbytes.
+
- SystemACE Support:
CONFIG_SYSTEMACE
Address, size and partition on the MMC to load U-Boot from
when the MMC is being used in raw mode.
+ CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
+ Sector to load kernel uImage from when MMC is being
+ used in raw mode (for Falcon mode)
+
+ CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
+ CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
+ Sector and number of sectors to load kernel argument
+ parameters from when MMC is being used in raw mode
+ (for falcon mode)
+
CONFIG_SPL_FAT_SUPPORT
Support for fs/fat/libfat.o in SPL binary
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
Filename to read to load U-Boot when reading from FAT
+ CONFIG_SPL_FAT_LOAD_KERNEL_NAME
+ Filename to read to load kernel uImage when reading
+ from FAT (for Falcon mode)
+
+ CONFIG_SPL_FAT_LOAD_ARGS_NAME
+ Filename to read to load kernel argument parameters
+ when reading from FAT (for Falcon mode)
+
CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
Set this for NAND SPL on PPC mpc83xx targets, so that
start.S waits for the rest of the SPL to load before
CONFIG_SPL_LIBGENERIC_SUPPORT
Support for lib/libgeneric.o in SPL binary
+ CONFIG_SPL_ENV_SUPPORT
+ Support for the environment operating in SPL binary
+
+ CONFIG_SPL_NET_SUPPORT
+ Support for the net/libnet.o in SPL binary.
+ It conflicts with SPL env from storage medium specified by
+ CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
+
CONFIG_SPL_PAD_TO
Image offset to which the SPL should be padded before appending
the SPL payload. By default, this is defined as
use an arch-specific makefile fragment instead, for
example if more than one image needs to be produced.
+ CONFIG_FIT_SPL_PRINT
+ Printing information about a FIT image adds quite a bit of
+ code to SPL. So this is normally disabled in SPL. Use this
+ option to re-enable it. This will affect the output of the
+ bootm command when booting a FIT image.
+
Modem Support:
--------------
offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
directly. You should not need to touch this setting.
+- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
+ This is set by OMAP boards for the max time that reset should
+ be asserted. See doc/README.omap-reset-time for details on how
+ the value can be calulated on a given board.
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
You will probably want to define these to avoid a really noisy system
when storing the env in UBI.
+- CONFIG_ENV_IS_IN_MMC:
+
+ Define this if you have an MMC device which you want to use for the
+ environment.
+
+ - CONFIG_SYS_MMC_ENV_DEV:
+
+ Specifies which MMC device the environment is stored in.
+
+ - CONFIG_SYS_MMC_ENV_PART (optional):
+
+ Specifies which MMC partition the environment is stored in. If not
+ set, defaults to partition 0, the user area. Common values might be
+ 1 (first MMC boot partition), 2 (second MMC boot partition).
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the environment
+ area within the specified MMC device.
+
+ If offset is positive (the usual case), it is treated as relative to
+ the start of the MMC partition. If offset is negative, it is treated
+ as relative to the end of the MMC partition. This can be useful if
+ your board may be fitted with different MMC devices, which have
+ different sizes for the MMC partitions, and you always want the
+ environment placed at the very end of the partition, to leave the
+ maximum possible space before it, to store other data.
+
+ These two values are in units of bytes, but must be aligned to an
+ MMC sector boundary.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
+ hold a redundant copy of the environment data. This provides a
+ valid backup copy in case the other copy is corrupted, e.g. due
+ to a power failure during a "saveenv" operation.
+
+ This value may also be positive or negative; this is handled in the
+ same way as CONFIG_ENV_OFFSET.
+
+ This value is also in units of bytes, but must also be aligned to
+ an MMC sector boundary.
+
+ - CONFIG_ENV_SIZE_REDUND (optional):
+
+ This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
+ set. If this value is set, it must be set to the same value as
+ CONFIG_ENV_SIZE.
+
- CONFIG_SYS_SPI_INIT_OFFSET
Defines offset to the initial SPI buffer area in DPRAM. The
a second time. Useful for platforms that are pre-booted
by coreboot or similar.
+- CONFIG_PCI_INDIRECT_BRIDGE:
+ Enable support for indirect PCI bridges.
+
- CONFIG_SYS_SRIO:
Chip has SRIO or not
- CONFIG_SRIO2:
Board has SRIO 2 port available
+- CONFIG_SRIO_PCIE_BOOT_MASTER
+ Board can support master function for Boot from SRIO and PCIE
+
- CONFIG_SYS_SRIOn_MEM_VIRT:
Virtual Address of SRIO port 'n' memory region
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_SYS_MPC85XX_NO_RESETVEC
+ Only for 85xx systems. If this variable is specified, the section
+ .resetvec is not kept and the section .bootpg is placed in the
+ previous 4k of the .text section.
+
- CONFIG_ARCH_MAP_SYSMEM
Generally U-Boot (and in particular the md command) uses
effective address. It is therefore not necessary to regard
using the "bootz" command. The syntax of "bootz" command is the same
as the syntax of "bootm" command.
-Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
+Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
kernel with raw initrd images. The syntax is slightly different, the
address of the initrd must be augmented by it's size, in the following
format: "<initrd addres>:<initrd size>".