config LOG
bool "Enable logging support"
+ select DM
help
This enables support for logging of status and debug messages. These
can be displayed on the console, recorded in a memory buffer, or
log message is shown - other details like level, category, file and
line number are omitted.
+config LOG_TEST
+ bool "Provide a test for logging"
+ depends on LOG
+ default y if SANDBOX
+ help
+ This enables a 'log test' command to test logging. It is normally
+ executed from a pytest and simply outputs logging information
+ in various different ways to test that the logging system works
+ correctly with varoius settings.
+
+config LOG_ERROR_RETURN
+ bool "Log all functions which return an error"
+ depends on LOG
+ help
+ When an error is returned in U-Boot it is sometimes difficult to
+ figure out the root cause. For eaxmple, reading from SPI flash may
+ fail due to a problem in the SPI controller or due to the flash part
+ not returning the expected information. This option changes
+ log_ret() to log any errors it sees. With this option disabled,
+ log_ret() is a nop.
+
+ You can add log_ret() to all functions which return an error code.
+
endmenu
+config SUPPORT_RAW_INITRD
+ bool "Enable raw initrd images"
+ help
+ Note, defining the SUPPORT_RAW_INITRD allows user to supply
+ kernel with raw initrd images. The syntax is slightly different, the
+ address of the initrd must be augmented by it's size, in the following
+ format: "<initrd address>:<initrd size>".
+
config DEFAULT_FDT_FILE
string "Default fdt file"
help
config DISPLAY_CPUINFO
bool "Display information about the CPU during start up"
- default y if ARM || NIOS2 || X86 || XTENSA
+ default y if ARM || NIOS2 || X86 || XTENSA || M68K
help
Display information about the CPU that U-Boot is running on
when U-Boot starts up. The function print_cpuinfo() is called
to do this.
config DISPLAY_BOARDINFO
- bool "Display information about the board during start up"
+ bool "Display information about the board during early start up"
default y if ARM || M68K || MIPS || PPC || SANDBOX || XTENSA
help
Display information about the board that U-Boot is running on
when U-Boot starts up. The board function checkboard() is called
to do this.
+config DISPLAY_BOARDINFO_LATE
+ bool "Display information about the board during late start up"
+ help
+ Display information about the board that U-Boot is running on after
+ the relocation phase. The board function checkboard() is called to do
+ this.
+
menu "Start-up hooks"
config ARCH_EARLY_INIT_R
Note that the normal serial console is not yet set up, but the
debug UART will be available if enabled.
+config BOARD_EARLY_INIT_R
+ bool "Call board-specific init after relocation"
+ help
+ Some boards need to perform initialisation as directly after
+ relocation. With this option, U-Boot calls board_early_init_r()
+ in the post-relocation init sequence.
+
+config LAST_STAGE_INIT
+ bool "Call board-specific as last setup step"
+ help
+ Some boards need to perform initialisation immediately before control
+ is passed to the command-line interpreter (e.g. for initializations
+ that depend on later phases in the init sequence). With this option,
+ U-Boot calls last_stage_init() before the command-line interpreter is
+ started.
+
endmenu
menu "Security support"
endmenu
+menu "Update support"
+
+config UPDATE_TFTP
+ bool "Auto-update using fitImage via TFTP"
+ depends on FIT
+ help
+ This option allows performing update of NOR with data in fitImage
+ sent via TFTP boot.
+
+config UPDATE_TFTP_CNT_MAX
+ int "The number of connection retries during auto-update"
+ default 0
+ depends on UPDATE_TFTP
+
+config UPDATE_TFTP_MSEC_MAX
+ int "Delay in mSec to wait for the TFTP server during auto-update"
+ default 100
+ depends on UPDATE_TFTP
+
+endmenu
+
source "common/spl/Kconfig"