work with minimal adjustments on other x86 boards since coreboot deals with
most of the low-level details.
+U-Boot is a main bootloader on Intel Edison board.
+
U-Boot also supports booting directly from x86 reset vector, without coreboot.
In this case, known as bare mode, from the fact that it runs on the
'bare metal', U-Boot acts like a BIOS replacement. The following platforms
are supported:
- Bayley Bay CRB
+ - Cherry Hill CRB
- Congatec QEVAL 2.0 & conga-QA3/E3845
- Cougar Canyon 2 CRB
- Crown Bay CRB
Building U-Boot as a coreboot payload is just like building U-Boot for targets
on other architectures, like below:
-$ make coreboot-x86_defconfig
+$ make coreboot_defconfig
$ make all
Note this default configuration will build a U-Boot payload for the QEMU board.
to point to a new board. You can also change the Cache-As-RAM (CAR) related
settings here if the default values do not fit your new board.
+Build Instructions for U-Boot as main bootloader
+------------------------------------------------
+
+Intel Edison instructions:
+
+Simple you can build U-Boot and obtain u-boot.bin
+
+$ make edison_defconfig
+$ make all
+
Build Instructions for U-Boot as BIOS replacement (bare mode)
-------------------------------------------------------------
Building a ROM version of U-Boot (hereafter referred to as u-boot.rom) is a
little bit tricky, as generally it requires several binary blobs which are not
shipped in the U-Boot source tree. Due to this reason, the u-boot.rom build is
not turned on by default in the U-Boot source tree. Firstly, you need turn it
-on by enabling the ROM build:
+on by enabling the ROM build either via an environment variable
-$ export BUILD_ROM=y
+ $ export BUILD_ROM=y
-This tells the Makefile to build u-boot.rom as a target.
+or via configuration
+
+ CONFIG_BUILD_ROM=y
+
+Both tell the Makefile to build u-boot.rom as a target.
---
6ef000 Environment CONFIG_ENV_OFFSET
6f0000 MRC cache CONFIG_ENABLE_MRC_CACHE
700000 u-boot-dtb.bin CONFIG_SYS_TEXT_BASE
-790000 vga.bin CONFIG_VGA_BIOS_ADDR
+7b0000 vga.bin CONFIG_VGA_BIOS_ADDR
7c0000 fsp.bin CONFIG_FSP_ADDR
7f8000 <spare> (depends on size of fsp.bin)
7ff800 U-Boot 16-bit boot CONFIG_SYS_X86_START16
Overall ROM image size is controlled by CONFIG_ROM_SIZE.
+Note that the debug version of the FSP is bigger in size. If this version
+is used, CONFIG_FSP_ADDR needs to be configured to 0xfffb0000 instead of
+the default value 0xfffc0000.
+
+---
+
+Intel Cherry Hill specific instructions for bare mode:
+
+This uses Intel FSP for Braswell platform. Download it from Intel FSP website,
+put the .fd file to the board directory and rename it to fsp.bin.
+
+Extract descriptor.bin and me.bin from the original BIOS on the board using
+ifdtool and put them to the board directory as well.
+
+Note the FSP package for Braswell does not ship a traditional legacy VGA BIOS
+image for the integrated graphics device. Instead a new binary called Video
+BIOS Table (VBT) is shipped. Put it to the board directory and rename it to
+vbt.bin if you want graphics support in U-Boot.
+
+Now you can build U-Boot and obtain u-boot.rom
+
+$ make cherryhill_defconfig
+$ make all
+
+An important note for programming u-boot.rom to the on-board SPI flash is that
+you need make sure the SPI flash's 'quad enable' bit in its status register
+matches the settings in the descriptor.bin, otherwise the board won't boot.
+
+For the on-board SPI flash MX25U6435F, this can be done by writing 0x40 to the
+status register by DediProg in: Config > Modify Status Register > Write Status
+Register(s) > Register1 Value(Hex). This is is a one-time change. Once set, it
+persists in SPI flash part regardless of the u-boot.rom image burned.
+
---
Intel Galileo instructions for bare mode:
- Set framebuffer graphics resolution (1280x1024 32k-color (1:5:5))
- Keep VESA framebuffer
+And include coreboot_fb.dtsi in your board's device tree source file, like:
+
+ /include/ "coreboot_fb.dtsi"
+
At present it seems that for Minnowboard Max, coreboot does not pass through
the video information correctly (it always says the resolution is 0x0). This
works correctly for link though.
+Note: coreboot framebuffer driver does not work on QEMU. The reason is unknown
+at this point. Patches are welcome if you figure out anything wrong.
+
Test with QEMU for bare mode
----------------------------
QEMU is a fancy emulator that can enable us to test U-Boot without access to
Here the kernel (bzImage) is loaded to 01000000 and initrd is to 04000000. Then,
'zboot' can be used to boot the kernel:
-=> zboot 02000000 - 04000000 1b1ab50
+=> zboot 01000000 - 04000000 1b1ab50
+
+Updating U-Boot on Edison
+-------------------------
+By default Intel Edison boards are shipped with preinstalled heavily
+patched U-Boot v2014.04. Though it supports DFU which we may be able to
+use.
+
+1. Prepare u-boot.bin as described in chapter above. You still need one
+more step (if and only if you have original U-Boot), i.e. run the
+following command:
+
+$ truncate -s %4096 u-boot.bin
+
+2. Run your board and interrupt booting to U-Boot console. In the console
+call:
+
+ => run do_force_flash_os
+
+3. Wait for few seconds, it will prepare environment variable and runs
+DFU. Run DFU command from the host system:
+
+$ dfu-util -v -d 8087:0a99 --alt u-boot0 -D u-boot.bin
+
+4. Return to U-Boot console and following hint. i.e. push Ctrl+C, and
+reset the board:
+
+ => reset
CPU Microcode
-------------
You can also bake this behaviour into your build by hard-coding the
environment variables if you add this to minnowmax.h:
-#undef CONFIG_BOOTARGS
#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_BOOTARGS \
- "root=/dev/sda2 ro"
#define CONFIG_BOOTCOMMAND \
"ext2load scsi 0:2 03000000 /boot/vmlinuz-3.13.0-58-generic; " \
"ext2load scsi 0:2 04000000 /boot/initrd.img-3.13.0-58-generic; " \
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS "boot=zboot 03000000 0 04000000 ${filesize}"
+and change CONFIG_BOOTARGS value in configs/minnowmax_defconfig to:
+
+CONFIG_BOOTARGS="root=/dev/sda2 ro"
+
Test with SeaBIOS
-----------------
SeaBIOS [14] is an open source implementation of a 16-bit x86 BIOS. It can run
to U-Boot. This should go at the top of each file and list the coreboot
filename where the code originated.
+Debugging ACPI issues with Windows:
+
+Windows might cache system information and only detect ACPI changes if you
+modify the ACPI table versions. So tweak them liberally when debugging ACPI
+issues with Windows.
+
ACPI Support Status
-------------------
Advanced Configuration and Power Interface (ACPI) [16] aims to establish
the compiler via "apt-get install iasl" if you are on Ubuntu or download
the source from [17] to compile one by yourself.
-Current ACPI support in U-Boot is not complete. More features will be added
-in the future. The status as of today is:
+Current ACPI support in U-Boot is basically complete. More optional features
+can be added in the future. The status as of today is:
* Support generating RSDT, XSDT, FACS, FADT, MADT, MCFG tables.
* Support one static DSDT table only, compiled by Intel ACPI compiler.
- * Support S0/S5, reboot and shutdown from OS.
+ * Support S0/S3/S4/S5, reboot and shutdown from OS.
* Support booting a pre-installed Ubuntu distribution via 'zboot' command.
* Support installing and booting Ubuntu 14.04 (or above) from U-Boot with
the help of SeaBIOS using legacy interface (non-UEFI mode).
of SeaBIOS using legacy interface (non-UEFI mode).
* Support ACPI interrupts with SCI only.
-Features not supported so far (to make it a complete ACPI solution):
- * S3 (Suspend to RAM), S4 (Suspend to Disk).
-
Features that are optional:
- * ACPI global NVS support. We may need it to simplify ASL code logic if
- utilizing NVS variables. Most likely we will need this sooner or later.
* Dynamic AML bytecodes insertion at run-time. We may need this to support
SSDT table generation and DSDT fix up.
* SMI support. Since U-Boot is a modern bootloader, we don't want to bring
those legacy stuff into U-Boot. ACPI spec allows a system that does not
support SMI (a legacy-free system).
-So far ACPI is enabled on BayTrail based boards. Testing was done by booting
+ACPI was initially enabled on BayTrail based boards. Testing was done by booting
a pre-installed Ubuntu 14.04 from a SATA drive. Installing Ubuntu 14.04 and
Windows 8.1/10 to a SATA drive and booting from there is also tested. Most
devices seem to work correctly and the board can respond a reboot/shutdown
command from the OS.
+For other platform boards, ACPI support status can be checked by examining their
+board defconfig files to see if CONFIG_GENERATE_ACPI_TABLE is set to y.
+
+The S3 sleeping state is a low wake latency sleeping state defined by ACPI
+spec where all system context is lost except system memory. To test S3 resume
+with a Linux kernel, simply run "echo mem > /sys/power/state" and kernel will
+put the board to S3 state where the power is off. So when the power button is
+pressed again, U-Boot runs as it does in cold boot and detects the sleeping
+state via ACPI register to see if it is S3, if yes it means we are waking up.
+U-Boot is responsible for restoring the machine state as it is before sleep.
+When everything is done, U-Boot finds out the wakeup vector provided by OSes
+and jump there. To determine whether ACPI S3 resume is supported, check to
+see if CONFIG_HAVE_ACPI_RESUME is set for that specific board.
+
+Note for testing S3 resume with Windows, correct graphics driver must be
+installed for your platform, otherwise you won't find "Sleep" option in
+the "Power" submenu from the Windows start menu.
+
+EFI Support
+-----------
+U-Boot supports booting as a 32-bit or 64-bit EFI payload, e.g. with UEFI.
+This is enabled with CONFIG_EFI_STUB. U-Boot can also run as an EFI
+application, with CONFIG_EFI_APP. The CONFIG_EFI_LOADER option, where U-Booot
+provides an EFI environment to the kernel (i.e. replaces UEFI completely but
+provides the same EFI run-time services) is not currently supported on x86.
+
+See README.efi for details of EFI support in U-Boot.
+
+64-bit Support
+--------------
+U-Boot supports booting a 64-bit kernel directly and is able to change to
+64-bit mode to do so. It also supports (with CONFIG_EFI_STUB) booting from
+both 32-bit and 64-bit UEFI. However, U-Boot itself is currently always built
+in 32-bit mode. Some access to the full memory range is provided with
+arch_phys_memset().
+
+The development work to make U-Boot itself run in 64-bit mode has not yet
+been attempted. The best approach would likely be to build a 32-bit SPL
+image for U-Boot, with CONFIG_SPL_BUILD. This could then handle the early CPU
+init in 16-bit and 32-bit mode, running the FSP and any other binaries that
+are needed. Then it could change to 64-bit model and jump to U-Boot proper.
+
+Given U-Boot's extensive 64-bit support this has not been a high priority,
+but it would be a nice addition.
+
TODO List
---------
- Audio
- Chrome OS verified boot
+- Building U-Boot to run in 64-bit mode
References
----------