/*
* DPRAM defines and allocation functions
*/
-
-/* The dual ported RAM is multi-functional. Some areas can be (and are
- * being) used for microcode. There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#ifdef CONFIG_SYS_ALLOC_DPRAM
-
-#define CPM_DATAONLY_BASE ((uint)0x0800)
-#define CPM_DATAONLY_SIZE ((uint)0x0700)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-
-#else
-
#define CPM_SERIAL_BASE 0x0800
#define CPM_I2C_BASE 0x0820
#define CPM_SPI_BASE 0x0840
#define CPM_POST_BASE 0x0980
#define CPM_WLKBD_BASE 0x0a00
-#endif
-
#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
#define CPM_POST_WORD_ADDR 0x07FC
#else
#define SICR_ENET_CLKRT ((uint)0x00002c00)
#endif /* CONFIG_BSEIP */
-/*** ESTEEM 192E **************************************************/
-#ifdef CONFIG_ESTEEM192E
-/* ESTEEM192E
- * This ENET stuff is for the MPC850 with ethernet on SCC2. This
- * is very similar to the RPX-Lite configuration.
- * Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
- */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003d00)
-
-#define PB_ENET_LOOPBACK ((uint)0x00004000)
-#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
-
-#endif
-
-/*** IP860 **********************************************************/
-
-#if defined(CONFIG_IP860)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
-#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
-
-/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002C)
-#endif /* CONFIG_IP860 */
-
/*** KM8XX *********************************************************/
/* The KM8XX Service Module uses SCC3 for Ethernet */