*/
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=ec000000.nor"
-#define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:128k(dtb),6016k(kernel)," \
- "57088k(fs),1m(vsc7385-firmware),1280k(u-boot)"
#endif
#if defined(CONFIG_TARGET_P1021RDB)
*/
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
#define CONFIG_FLASH_CFI_MTD
-#ifdef CONFIG_PHYS_64BIT
-#define MTDIDS_DEFAULT "nor0=fef000000.nor"
-#define MTDPARTS_DEFAULT "mtdparts=fef000000.nor:256k(vsc7385-firmware)," \
- "256k(dtb),4608k(kernel),9728k(fs)," \
- "256k(qe-ucode-firmware),1280k(u-boot)"
-#else
-#define MTDIDS_DEFAULT "nor0=ef000000.nor"
-#define MTDPARTS_DEFAULT "mtdparts=ef000000.nor:256k(vsc7385-firmware)," \
- "256k(dtb),4608k(kernel),9728k(fs)," \
- "256k(qe-ucode-firmware),1280k(u-boot)"
-#endif
#endif
#if defined(CONFIG_TARGET_P1024RDB)
*/
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
#define CONFIG_FLASH_CFI_MTD
-#ifdef CONFIG_PHYS_64BIT
-#define MTDIDS_DEFAULT "nor0=fef000000.nor"
-#define MTDPARTS_DEFAULT "mtdparts=fef000000.nor:256k(vsc7385-firmware)," \
- "256k(dtb),4608k(kernel),9984k(fs),1280k(u-boot)"
-#else
-#define MTDIDS_DEFAULT "nor0=ef000000.nor"
-#define MTDPARTS_DEFAULT "mtdparts=ef000000.nor:256k(vsc7385-firmware)," \
- "256k(dtb),4608k(kernel),9984k(fs),1280k(u-boot)"
-#endif
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CMD_SATA
-#define CONFIG_SATA_SIL
#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_LIBATA
#define CONFIG_LBA48
#if defined(CONFIG_TARGET_P2020RDB)
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_CMD_NAND
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#else
#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
/* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#endif
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_CMD_PCI
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHPRIME "eTSEC1"
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
* Environment
*/
#ifdef CONFIG_SPIFLASH
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 10000000
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
#elif defined(CONFIG_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0
#else
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
#endif
-#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET (1024 * 1024)
#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#else
-#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_REGINFO
-
/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_DESC_BIG_ENDIAN
#endif
#endif
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
- || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
- /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
#ifdef __SW_BOOT_NOR
#define __NOR_RST_CMD \
norboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_NOR 1; \