X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;ds=sidebyside;f=README;h=67dc444bd4d0bbe92d2cefcf45b220d079f98c37;hb=ac486e3ba16c37514d135c359f61ed6e32a2921d;hp=f726303e1977d774f65bd8f0b8877cb5bd259eed;hpb=c8339f51537dbbfa5e4b526f649dc4997c3df3c5;p=u-boot

diff --git a/README b/README
index f726303e19..67dc444bd4 100644
--- a/README
+++ b/README
@@ -432,6 +432,14 @@ The following options need to be configured:
 		Select high exception vectors of the ARM core, e.g., do not
 		clear the V bit of the c1 register of CP15.
 
+		CONFIG_SYS_THUMB_BUILD
+
+		Use this flag to build U-Boot using the Thumb instruction
+		set for ARM architectures. Thumb instruction set provides
+		better code density. For ARM architectures that support
+		Thumb2 this flag will result in Thumb2 code generated by
+		GCC.
+
 - Linux Kernel Interface:
 		CONFIG_CLOCKS_IN_MHZ
 
@@ -777,6 +785,8 @@ The following options need to be configured:
 		CONFIG_CMD_JFFS2	* JFFS2 Support
 		CONFIG_CMD_KGDB		* kgdb
 		CONFIG_CMD_LDRINFO	  ldrinfo (display Blackfin loader)
+		CONFIG_CMD_LINK_LOCAL	* link-local IP address auto-configuration
+					  (169.254.*.*)
 		CONFIG_CMD_LOADB	  loadb
 		CONFIG_CMD_LOADS	  loads
 		CONFIG_CMD_MD5SUM	  print md5 message digest
@@ -1584,10 +1594,17 @@ The following options need to be configured:
 		CONFIG_BOOTP_NTPSERVER
 		CONFIG_BOOTP_TIMEOFFSET
 		CONFIG_BOOTP_VENDOREX
+		CONFIG_BOOTP_MAY_FAIL
 
 		CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
 		environment variable, not the BOOTP server.
 
+		CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
+		after the configured retry count, the call will fail
+		instead of starting over.  This can be used to fail over
+		to Link-local IP address configuration if the DHCP server
+		is not available.
+
 		CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
 		serverip from a DHCP server, it is possible that more
 		than one DNS serverip is offered to the client.
@@ -1618,6 +1635,14 @@ The following options need to be configured:
 		the DHCP timeout and retry process takes a longer than
 		this delay.
 
+ - Link-local IP address negotiation:
+		Negotiate with other link-local clients on the local network
+		for an address that doesn't require explicit configuration.
+		This is especially useful if a DHCP server cannot be guaranteed
+		to exist in all environments that the device must operate.
+
+		See doc/README.link-local for more information.
+
  - CDP Options:
 		CONFIG_CDP_DEVICE_ID
 
@@ -3026,6 +3051,24 @@ to save the current settings.
 	  environment area within the total memory of your DataFlash placed
 	  at the specified address.
 
+- CONFIG_ENV_IS_IN_REMOTE:
+
+	Define this if you have a remote memory space which you
+	want to use for the local device's environment.
+
+	- CONFIG_ENV_ADDR:
+	- CONFIG_ENV_SIZE:
+
+	  These two #defines specify the address and size of the
+	  environment area within the remote memory space. The
+	  local device can get the environment from remote memory
+	  space by SRIO or other links.
+
+BE CAREFUL! For some special cases, the local device can not use
+"saveenv" command. For example, the local device will get the
+environment stored in a remote NOR flash by SRIO link, but it can
+not erase, write this NOR flash by SRIO interface.
+
 - CONFIG_ENV_IS_IN_NAND:
 
 	Define this if you have a NAND device which you want to use
@@ -3462,6 +3505,12 @@ within that device.
 	Specifies that QE/FMAN firmware is located on the primary SPI
 	device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
 
+- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+	Specifies that QE/FMAN firmware is located in the remote (master)
+	memory space.	CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
+	can be mapped from slave TLB->slave LAW->slave SRIO outbound window
+	->master inbound window->master LAW->the ucode address in master's
+	NOR flash.
 
 Building the Software:
 ======================