X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=CHANGELOG;h=820974188317e7005e82ceca4b7e83f3b09e368b;hb=c6525d459c350bfc246ea7826456af77e1e314eb;hp=cc08e1110eaef4d9701532e152f8f08c0e822352;hpb=285db74716c724ae8a0ff177878fd09a74428c7b;p=u-boot diff --git a/CHANGELOG b/CHANGELOG index cc08e1110e..8209741883 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,3 +1,4384 @@ +commit f7a35a60cf45491871a5c28e9ad24db005487857 +Author: Heiko Schocher +Date: Fri Oct 17 18:24:06 2008 +0200 + + mgcoge: add redundant environment sector + + Signed-off-by: Heiko Schocher + Signed-off-by: Wolfgang Denk + +commit c2537ee85954af9d036b18b644f3e18d837bf4a5 +Author: Heiko Schocher +Date: Fri Oct 17 18:23:27 2008 +0200 + + mgsuvd: update size of environment + + Signed-off-by: Heiko Schocher + +commit fa7b1c07e9371aea8f87ee6d3c2ea5564bd8cc8d +Author: Lepcha Suchit +Date: Thu Oct 16 13:38:00 2008 -0500 + + 83xx NAND boot: wait for LTESR[CC] + + At least some revisions of the 8313, and possibly other chips, do not + wait for all pages of the initial 4K NAND region to be loaded before + beginning execution; thus, we wait for it before branching out of the + first NAND page. + + This fixes warm reset problems when booting from NAND on 8313erdb. + + Signed-off-by: Scott Wood + Acked-by: Kim Phillips + +commit bf29e0ea0af03d593c64614136acc723a7a022a2 +Author: Yuri Tikhonov +Date: Fri Oct 17 12:54:18 2008 +0200 + + ppc4xx: PPC44x MQ initialization + + Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC + values. This fixes the occasional 440SPe hard locking issues when the 440SPe's + dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver). + + Previously the appropriate initialization had been made in Linux, by the + ppc440spe ADMA driver, which is wrong because modifying the MQ configuration + registers after normal operation has begun is not supported and could + have unpredictable results. + + Comment from Stefan: This patch doesn't change the resulting value of the + MQ registers. It explicitly sets/clears all bits to the desired state which + better documents the resulting register value instead of relying on pre-set + default values. + + Signed-off-by: Yuri Tikhonov + Signed-off-by: Stefan Roese + +commit f7d190b1c0b3ab7fc53074ad2862f7de99de37ff +Author: Kumar Gala +Date: Thu Oct 16 21:58:50 2008 -0500 + + 85xx: Using proper I2C source clock divider for MPC8544 + + The MPC8544 RM incorrect shows the SEC_CFG bit in PORDEVSR2 as being + bit 26, instead it should be bit 28. This caused in incorrect + interpretation of the i2c_clk which is the same as the SEC clk on + MPC8544. The SEC clk is controlled by cfg_sec_freq that is reported + in PORDEVSR2. + + Signed-off-by: Kumar Gala + +commit 42653b826adb319a1df06e24ef26096b2a5d9d2a +Author: Kumar Gala +Date: Thu Oct 16 21:58:49 2008 -0500 + + Revert "85xx: Using proper I2C source clock divider for MPC8544" + + This reverts commit dffd2446fb041f38ef034b0fcf41e51e5e489159. + + The fix introduced by this patch is not correct. The problem is + that the documentation is not correct for the MPC8544 with regards + to which bit in PORDEVSR2 is for the SEC_CFG. + + Signed-off-by: Kumar Gala + +commit 2179c4766bffeece98e5e92040629a96c97e230c +Author: Kumar Gala +Date: Wed Oct 15 10:19:41 2008 -0500 + + 85xx: Fix compile warning + + mpc8536ds.c: In function 'is_sata_supported': + mpc8536ds.c:614: warning: unused variable 'devdisr' + + Signed-off-by: Kumar Gala + +commit 9029b68f3f81b3013044f167ea025e836e6c8c0e +Author: Jason Jin +Date: Wed Oct 15 10:40:24 2008 +0800 + + Fix the function conflict in x86emu when DEBUG is on + + The function parse_line() in common/main.c was exposed globally by commit + 6636b62a6efc7f14e6e788788631ae7a7fca4537, Result in conflict with the same + name funciton in drivers/bios_emulator/x86emu/debug.c when define the DEBUG. + This patch fix this by renaming the function in the debug.c file. + + Signed-off-by: Jason Jin + +commit b4dbacf69a669a17487054552fc2761149dd6767 +Author: Wolfgang Denk +Date: Wed Oct 15 15:50:45 2008 +0200 + + Coding Style cleanup, update CHANGELOG, prepare 2008.10-rc3 + + Signed-off-by: Wolfgang Denk + +commit 374b9038293d01d8744a46af9b7854a6fd99b228 +Author: Heiko Schocher +Date: Wed Oct 15 09:51:19 2008 +0200 + + Fix compiler warning in lib_ppc/board.c + + Fix compiler warning introduced by commit 0f8cbc18 + + Signed-off-by: Heiko Schocher + Signed-off-by: Wolfgang Denk + +commit 9724555755a6f1066636481b41f7094e0ce93a69 +Author: Selvamuthukumar +Date: Thu Oct 9 10:29:14 2008 +0530 + + mpc83xx: wait till UPM completes the write to array + + Reference manual states that MxMR[MAD] increment is the indication + of write to UPM array is complete. Honour that. Also, make the dummy + write explicit. + + also fix the comment. + + Signed-off-by: Selvamuthukumar + Signed-off-by: Kim Phillips + +commit 03e2dbb18e858e2f7a6aaa437f290f3690d02d51 +Author: Selvamuthukumar +Date: Wed Oct 8 18:12:20 2008 -0500 + + Remove unwanted ';' at end of define. + + Currently this is not creating any problem. But it will result + in compilation error when used as below. + + printf("CFG_SDRAM_CFG2 - %08x\n", CFG_SDRAM_CFG2); + + Signed-off-by: Selvamuthukumar + + continuation of the theme based on git grep "^#define CFG_.*;$" include/ + + Signed-off-by: Kim Phillips + +commit b2934a56650e9a6c54432f9ce6dc36757967385e +Author: Hugo Villeneuve +Date: Mon Oct 6 10:53:59 2008 -0400 + + ARM DaVinci: Add maintainer information for SFFSDR board. + + Signed-off-by: Hugo Villeneuve + +commit 12c6670f873ed632c264a6f3e8bf1297d5c3ddbc +Author: Matthias Fuchs +Date: Sat Oct 4 19:26:16 2008 +0200 + + api: fix type mismatch + + This patch fixes a type mismatch and thus removes a compiler + warning when compiling with CONFIG_API on powerpc. + + Signed-off-by: Matthias Fuchs + +commit 9bc2e4eee3bcb8e63847d7a733e0c607807d6141 +Author: Peter Tyser +Date: Wed Oct 1 12:25:04 2008 -0500 + + cmd_i2c: Fix help for CONFIG_I2C_CMD_TREE && !CONFIG_I2C_MULTI_BUS + + Original code displayed: + => help i2c + i2c i2c speed [speed] - show or set I2C bus speed + i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device + ... + + Signed-off-by: Peter Tyser + +commit a0b1b610e980e253d4c2519ee15bd0937c3f8be1 +Author: Wolfgang Denk +Date: Tue Oct 14 22:13:41 2008 +0200 + + Update CHANGELOG + + Signed-off-by: Wolfgang Denk + +commit 0f8cbc1829d9c7d9616fd29b366a99d037facdcd +Author: Jason Jin +Date: Fri Oct 10 11:41:01 2008 +0800 + + Do not init SATA when disabled on 8536DS. + + SGMII and SATA share the serdes on MPC8536 CPU, When SATA disabled and the + driver still try to access the SATA registers, the cpu will hangup. + This patch try to fix this by reading the serdes status before the SATA + initialize. + + Signed-off-by: Jason Jin + Acked-by: Andy Fleming + +commit ec4d8c1c1d94a790c1473ae8aace282b817c3123 +Author: Nikita V. Youshchenko +Date: Fri Oct 3 00:03:55 2008 +0400 + + fsl_diu: fix alignment error that caused malloc corruption + + When aligning malloc()ed screen_base, invalid offset was added. + This not only caused misaligned result (which did not cause hardware + misbehaviour), but - worse - caused screen_base + smem_len to + be out of malloc()ed space, which in turn caused breakage of + futher malloc()/free() operation. + + This patch fixes screen_base alignment. + + Also this patch makes memset() that cleans framebuffer to be executed + on first initialization of diu, not only on re-initialization. It looks + correct to clean the framebuffer instead of displaying random garbage; + I believe that was disabled only because that memset caused breakage + of malloc/free described above - which no longer happens with the fix + described above. + + Signed-off-by: Nikita V. Youshchenko + +commit 3d0ea3110f3431b6c2aee882784f39f97b20bce9 +Author: Matthias Fuchs +Date: Wed Sep 24 10:29:37 2008 +0200 + + api: Fix building with CONFIG_API + + This patch fixes building with CONFIG_API and CONFIG_USB_STORAGE. + + USB_MAX_STOR_DEV is defined in include/usb.h, but + needed in api/api_storage.c. + + Signed-off-by: Matthias Fuchs + +commit abbb90666d5ef2f500ebbedbb80ff60adc56b043 +Author: Peter Tyser +Date: Tue Sep 23 12:39:40 2008 -0500 + + Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE references + + Signed-off-by: Peter Tyser + +commit 81e612014c40c922ec35488d17c504d4e9286f06 +Author: Peter Tyser +Date: Tue Sep 23 12:38:42 2008 -0500 + + Remove CFG_EEPROM_PAGE* dependencies for temperature sensors + + The checks for CFG_EEPROM_PAGE_WRITE_ENABLE and + CFG_EEPROM_PAGE_WRITE_BITS in various temperature + sensor drivers are not necessary + + Signed-off-by: Peter Tyser + +commit c46980f6d2135ade345dadc1fb1f1f4c8bbf255a +Author: Mike Frysinger +Date: Tue Oct 14 07:04:38 2008 -0400 + + cmd_spi: remove broken signed casting for display + + Since we're working with unsigned data, you can't apply a signed pointer + cast and then attempt to print the result. Otherwise you get wrong output + when the sign bit is set like "0xFF" incorrectly extended to "0xFFFFFFFF". + + Signed-off-by: Mike Frysinger + +commit d5fd0b49210c941de8a1fce3947ace92243ab5ca +Author: Mike Frysinger +Date: Tue Oct 14 07:05:24 2008 -0400 + + strings cmd: drop old CONFIG_CFG_STRINGS define + + We don't need CONFIG_CFG_STRINGS anymore now that we have the define + CONFIG_CMD_STRINGS and Makefile control. + + Signed-off-by: Mike Frysinger + +commit fecb5ade3b37f62981f2b05b621005850173aaa9 +Author: Jason Jin +Date: Fri Sep 19 17:32:49 2008 +0800 + + Fix the NAND size overflow issue. + + When the total size of all NAND devices exceeds 4 GiB, the size will + overflow. This patch tries to fix this. + + Note that we still have a problem when a single NAND device is bigger + than 4 GiB: then the overflow would actually happen earlier, i. e. + when storing the size in nand_info[].size, as nand_info[].size is an + "u_int32_t". + + Signed-off-by: Jason Jin + Signed-off-by: Wolfgang Denk + +commit 30f574717277238b9014b8136c90eea77196490f +Author: Louis Su +Date: Wed Jul 9 11:01:37 2008 +0800 + + AX88180: new gigabit network driver + + Signed-off-by: Louis Su + Signed-off-by: Ben Warren + +commit c9d6b6925344740ca1db2f8a6bab7921ff820de3 +Author: Andre Schwarz +Date: Tue Aug 19 16:07:03 2008 +0200 + + enable 10/100M at VSC8601 at tsec driver + + Currently VSC8601 doesn't link with 10/100M partners if the + EEPROM/Strapping is not set up. + Setting the auto-neg register fixes this. + + Signed-off-by: Andre Schwarz + Signed-off-by: Ben Warren + +commit 702c85b0e876d587c11acdbb55738ee52acd54f4 +Author: Nobuhiro Iwamatsu +Date: Tue Sep 30 15:02:53 2008 +0900 + + net: ne2000: Divided a function of NE2000 driver + + get_prom function was used __attriute__ , but it is not enable. + ax88796.o does not do link besides ne2000.o. When ld is carried + out, get_prom function of ax88796.c is ignored. + This problem is a thing by specifications of ld. + I checked and test this patch on SuperH and MIPS. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Ben Warren + +commit 05c7e9070fe4d751e029fd9524bfbbc93cbb1393 +Author: Nobuhiro Iwamatsu +Date: Tue Oct 14 11:10:59 2008 +0900 + + sh: rsk7203: Add smc911x driver support to board config file + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit cae6f909baf86357b3c0bd01acfc414348c4d175 +Author: Nobuhiro Iwamatsu +Date: Thu Oct 9 13:54:33 2008 +0900 + + sh: Fix cannot execute a stand-alone application + + Address calculated in EXPORT_FUNC in SuperH was wrong, I revised it. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 6df0efd5c86ca1689deeb2738b46b7d83ce228ef +Author: Ed Swarthout +Date: Wed Oct 8 23:38:00 2008 -0500 + + fsl_pci_init do not scan bus when configured as an end-point + + Signed-off-by: Ed Swarthout + Acked-by: Andy Fleming + +commit 6f099bbac1ba5dfb46ee7ad29dc53713f0501ba5 +Author: Hugo Villeneuve +Date: Tue Sep 16 17:07:53 2008 -0400 + + ARM DaVinci: Remove redundant setting of GD_FLG_RELOC for sffsdr board. + + This is no longer necessary now that the GD_FLG_RELOC flag is set for + all ARM boards. + + Signed-off-by: Hugo Villeneuve + +commit d977a57356657ba241256231efca32828a5822f9 +Author: Luigi 'Comio' Mantellini +Date: Sat Sep 13 10:04:32 2008 +0200 + + Fix lzma uncompress call (image_start wrongly used instead image_len) + + Signed-off-by: Luigi 'Comio' Mantellini + +commit 392438406041415fe64ab8748ec5ab5ad01d1cf7 +Author: Nick Spence +Date: Thu Aug 28 14:09:15 2008 -0700 + + mpc86xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache + + This is needed in unlock_ram_in_cache() because it is called from C and + will corrupt the small data area anchor that is kept in R2. + + lock_ram_in_cache() is modified similarly as good coding practice, but + is not called from C. + + Signed-off-by: Nick Spence + +commit 5c7cbcd34d0ee566875a4fd0f2a3e5a62bba921c +Author: Kumar Gala +Date: Tue Aug 19 15:05:34 2008 -0500 + + 86xx: remove redudant code with lib_ppc/interrupts.c + + For some reason we duplicated the majority of code in lib_ppc/interrupts.c + Not know how that happened, but there is no good reason for it. + + Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why + they exist. + + Signed-off-by: Kumar Gala + +commit 0d01f66d235118515b5086b88f82498bc0695d6a +Author: Ed Swarthout +Date: Thu Oct 9 01:26:36 2008 -0500 + + CFI: cfi_flash write fix for AMD legacy + + The flash_unlock_seq requires a sector for AMD_LEGACY. + Fix a retcode check typeo. + + Signed-off-by: Ed Swarthout + Signed-off-by: Stefan Roese + +commit 542b385a620a1783454a00424930e51895f45073 +Author: Matthias Fuchs +Date: Tue Oct 7 13:13:10 2008 +0200 + + ppc4xx: Fix USB 2.0 phy reset sequence + + This patch fixes USB 2.0 communication issues on some DU440 boards. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit df8c1ce11114c2260dedb5547281945f7db8fa5c +Author: Matthias Fuchs +Date: Tue Oct 7 13:13:09 2008 +0200 + + ppc4xx: Add strapping mode for 667MHz CPU frequency on DU440 board + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 6a133d6a00b1fc7b9257cd5925d8cb67f75ecda2 +Author: Matthias Fuchs +Date: Tue Oct 7 13:13:08 2008 +0200 + + ppc4xx: Fix DU440 GPIO configuration + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 35dd025c70fcc4389317db2f2a9d14795172137d +Author: Matthias Fuchs +Date: Tue Oct 7 13:13:07 2008 +0200 + + ppc4xx: Update DU440 config + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit f3bf9273939ffe1a60a32a2eef909097f15df56b +Author: Kumar Gala +Date: Wed Oct 8 15:36:39 2008 -0500 + + MPC8572DS: Fix compile warnings + + Commit 445a7b38308eb05b41de74165b20855db58c7ee5 introduced the following + compile warnings: + + cmd_i2c.c:112: warning: missing braces around initializer + cmd_i2c.c:112: warning: (near initialization for 'i2c_no_probes[0]') + + Signed-off-by: Kumar Gala + +commit dffd2446fb041f38ef034b0fcf41e51e5e489159 +Author: Wolfgang Grandegger +Date: Tue Sep 30 10:55:57 2008 +0200 + + 85xx: Using proper I2C source clock divider for MPC8544 + + Measurements with our MPC8544 board showed that the I2C bus frequency + is wrong by a factor of 1.5. Obviously, the interpretation of the + MPC85xx_PORDEVSR2_SEC_CFG bit of the cfg_sec_freq register is not + correct. There seems to be an error in the 8544 RM. + + Signed-off-by: Wolfgang Grandegger + +commit e46c7bfb8bc3c304cedd20f7a365d6e78d7eaf17 +Author: Rafal Czubak +Date: Wed Oct 8 13:41:30 2008 +0200 + + FSL: Fix get_cpu_board_revision() return value. + + get_cpu_board_revision() returned board revision based on information stored + in global static struct eeprom. It should instead use one from local struct + board_eeprom, to which the data is actually read from EEPROM. The bug led to + system hang after printing L1 cache information on U-Boot startup. The problem + was observed on MPC8555CDS system and possibly affects other Freescale MPC85xx + boards using CFG_I2C_EEPROM_CCID. + + The change has been successfully tested on MPC8555CDS system. + + Signed-off-by: Rafal Czubak + +commit 747f316cca484ed627a97dd3391febabce384186 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 30 20:08:49 2008 +0200 + + update uImage FIT multi documentation + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 77a0355f60b801f232ce0a5bfbe95331fa3b6bc0 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 30 20:08:36 2008 +0200 + + move README.imx31 to doc/ and merge with README.mx31 + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 1ed7a7f0f571b13d46530f8f8b9aff3957f15a96 +Author: Guennadi Liakhovetski +Date: Thu Sep 25 20:54:37 2008 +0200 + + i.MX31: switch to CFG_HZ=1000 + + Switch to the standard CFG_HZ=1000 value, while at it, minor white-space + cleanup, remove CFG_CLKS_IN_HZ from config-headers. Tested on mx31ads, + provides 2% or 0.4% precision depending on the + CONFIG_MX31_TIMER_HIGH_PRECISION flag. Measured with stop-watch on 100s + boot-delay. + + Signed-off-by: Guennadi Liakhovetski + +commit f41b144c11341b571eab7dcef6c4b8e03c92d2b2 +Author: gnusercn +Date: Wed Oct 8 18:58:58 2008 +0200 + + Fix bug: in arch-arm, env_get_char dose not work fine + + due to the arm implementation which supposed that U-Boot is in RAM + when we jump to start_armboot + + Signed-off-by: gnusercn + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit f8a00dea841d5d75de1f8e8107e90ee1beeddf5f +Author: Adam Graham +Date: Mon Oct 6 10:16:13 2008 -0700 + + ppc4xx: Reset and relock memory DLL after SDRAM_CLKTR change + + After changing SDRAM_CLKTR phase value rerun the memory preload + initialization sequence (INITPLR) to reset and relock the memory + DLL. Changing the SDRAM_CLKTR memory clock phase coarse timing + adjustment effects the phase relationship of the internal, to the + PPC chip, and external, to the PPC chip, versions of MEMCLK_OUT. + + Signed-off-by: Adam Graham + Signed-off-by: Victor Gallardo + Signed-off-by: Stefan Roese + +commit 5297246bbaa9943c0da1ec2e717b72e4ab6b830e +Author: Haiying Wang +Date: Fri Oct 3 11:48:03 2008 -0400 + + Remove redundant #define for MPC8536DS + + Signed-off-by: Haiying Wang + +commit 445a7b38308eb05b41de74165b20855db58c7ee5 +Author: Haiying Wang +Date: Fri Oct 3 11:47:30 2008 -0400 + + Add ID EEPROM support for MPC8572DS + + The ID EEPROM on MPC8572DS board locates on I2C bus 1. Its the storage for + system information like mac addresses etc. This patch enables it. + + Signed-off-by: Haiying Wang + +commit 1f3ba317a5c5f3a7aabf580fddc211f4bb5a4540 +Author: Haiying Wang +Date: Fri Oct 3 11:46:59 2008 -0400 + + Minor fixes for I2C address on MPC8572DS + + MPC8572DS has two i2c buses. This patch moves the DDR SPD_EEPROM to i2c bus 1 + according to the board spec, and adds the 2nd i2c bus offset. + + Signed-off-by: Haiying Wang + +commit c0391111c33c22fabeddf8f4ca801ec7645b4f5c +Author: Jason Jin +Date: Sat Sep 27 14:40:57 2008 +0800 + + Fix the incorrect DDR clk freq reporting on 8536DS + + On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111), + The display is still sync mode DDR freq. This patch try to fix + this. The display DDR freq is now the actual freq in both + sync and async mode. + + Signed-off-by: Jason Jin + +commit bac6a1d1fa1cd80aa57881fa9c2152b853cd0ed4 +Author: Kumar Gala +Date: Tue Oct 7 10:28:46 2008 -0500 + + 85xx: Remove setting of *cache-line-size in device trees + + ePAPR says if the *cache-block-size is the same as *cache-line-size + than we don't need the *cache-line-size property. + + Signed-off-by: Kumar Gala + +commit cd3cb0d9269d155276b00207e3816a9347fd1c92 +Author: Gerald Van Baren +Date: Sat Oct 4 07:56:06 2008 -0400 + + libfdt: Fix error in documentation for fdt_get_alias_namelen() + + Oops, screwed up the function name in the documenting comment for this + function. Trivial correction in this patch. + + Signed-off-by: David Gibson + Acked-by: Gerald Van Baren + +commit 9a6cf73a88ddab2e1ac39088f2806177982cc62c +Author: David Gibson +Date: Wed Aug 20 16:55:14 2008 +1000 + + libfdt: Add function to explicitly expand aliases + + Kumar has already added alias expansion to fdt_path_offset(). + However, in some circumstances it may be convenient for the user of + libfdt to explicitly get the string expansion of an alias. This patch + adds a function to do this, fdt_get_alias(), and uses it to implement + fdt_path_offset(). + + Signed-off-by: David Gibson + +commit 2215987e100d2a841ae6d48a7cc9bb83fcf22737 +Author: Mike Frysinger +Date: Thu Oct 2 01:55:38 2008 -0400 + + cfi_flash: do not reset flash when probe fails + + The CFI flash driver starts at flash_init() which calls down into + flash_get_size(). This starts by calling flash_detect_cfi(). If said + function fails, flash_get_size() finishes by attempting to reset the + flash. Unfortunately, it does this with an info->portwidth set to 0x10 + which filters down into flash_make_cmd() and that happily smashes the + stack by sticking info->portwidth bytes into a cfiword_t variable that + lives on the stack. On a 64bit system you probably won't notice, but + killing the last 8 bytes on a 32bit system usually leads to a corrupt + return address. Which is what happens on a Blackfin system. + + Signed-off-by: Mike Frysinger + Signed-off-by: Stefan Roese + +commit 3e38577208e4256956bc33bb8bcd0a6b6fab55c3 +Author: Stefan Roese +Date: Fri Sep 26 17:03:26 2008 +0200 + + fdt: Overwrite /chosen node in bootm if it already exists in the dtb + + Set force parameter in fdt_chosen() call in do_bootm_linux() call. + Without this, the chosen node is not overwritten if it already + exists. + + Signed-off-by: Stefan Roese + +commit 741a6d010d09b5bafca8e4cdfb6b2f8a2c07994d +Author: Jon Loeliger +Date: Thu Sep 25 11:02:17 2008 -0500 + + Fix an overflow case in fdt_offset_ptr() detected by GCC 4.3. + + Using Gcc 4.3 detected this problem: + + ../dtc/libfdt/fdt.c: In function 'fdt_next_tag': + ../dtc/libfdt/fdt.c:82: error: assuming signed overflow does not + occur when assuming that (X + c) < X is always false + + To fix the problem, treat the offset as an unsigned int. + + The problem report and proposed fix were provided + by Steve Papacharalambous . + + Signed-off-by: Jon Loeliger + +commit bbdbc7cb3abefda5bd998edbcf0508fe6256327d +Author: David Gibson +Date: Fri Aug 29 14:19:13 2008 +1000 + + libfdt: Fix bugs in fdt_get_path() + + The current implementation of fdt_get_path() has a couple of bugs, + fixed by this patch. + + First, contrary to its documentation, on success it returns the length + of the node's path, rather than 0. The testcase is correspondingly + wrong, and the patch fixes this as well. + + Second, in some circumstances, it will return -FDT_ERR_BADOFFSET + instead of -FDT_ERR_NOSPACE when given insufficient buffer space. + Specifically this happens when there is insufficient space even to + hold the path's second last component. This behaviour is corrected, + and the testcase updated to check it. + + Signed-off-by: David Gibson + +commit 33af3e6656e84660d397b5dd95abab2dccc36f83 +Author: Wolfgang Denk +Date: Wed Oct 1 12:34:58 2008 +0200 + + TQM5200: enable support for ATAPI devices + + Signed-off-by: Wolfgang Denk + +commit d13ff2358ff8c384f52eaf46f5d60258acf96ea6 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Sep 15 05:48:25 2008 +0200 + + Revert "ARM: set GD_FLG_RELOC for boards skipping relocation to RAM" + + we need this due to the arm implementation which supposed that U-Boot + is in RAM when we jump to start_armboot + + This reverts commit f96b44cef897bd372beb86dde1b33637c119d84d. + in order to do it for all arm board + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 7fd0bea2e4a78eab7e6693140940f9f9a0009bc2 +Author: Kim Phillips +Date: Wed Sep 24 08:46:25 2008 -0500 + + mpc83xx: don't disable autoboot + + bootdelay set to -1 'permanently' disables autobooting, even if + bootcmd is specified. Change to a positive value to allow + autobooting when a bootcmd is set. + + Reported-by: Coray Tate + Cc: Scott Wood + Signed-off-by: Kim Phillips + +commit 2fb29c520c42b7bfef33ea3fd1527eba64099164 +Author: Nobuhiro Iwamatsu +Date: Wed Sep 24 10:42:15 2008 +0900 + + mpc83xx: Fix typo in include/mpc83xx.h + + Fixed typo from CONIFG_MPC837X to CONFIG_MPC837X + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Kim Phillips + +commit 162c41c03179727a1d14262f703c9a8bc40231fa +Author: Kim Phillips +Date: Tue Sep 23 09:38:49 2008 -0500 + + mpc83xx: add h/w flash protection to board configs + + the operating system may leave flash in a h/w locked state after writing. + This allows u-boot to continue to write flash by enabling h/w unlocking + by default. + + Signed-off-by: Kim Phillips + +commit d26154c9a692586b66eb6d1f8e1b67c75e40ea70 +Author: Anton Vorontsov +Date: Thu Sep 11 21:35:36 2008 +0400 + + mpc83xx: spd_sdram: fix ddr sdram base address assignment bug + + The spd_dram code shifts the base address, then masks 20 bits, but + forgets to shift the base address back. Fix this by just masking the + base address correctly. + + Found this bug while trying to relocate a DDR memory at the base != 0. + + Signed-off-by: Anton Vorontsov + Signed-off-by: Kim Phillips + +commit 8fd4166c467a46773f80208bda1ec3b4757747bc +Author: Stefan Roese +Date: Mon Sep 22 16:10:43 2008 +0200 + + ppc4xx: Canyonlands: Remove unnecessary FDT warning upon DTB fixup + + Depending on the configuration jumper "SATA SELECT", U-Boot disabled + either one PCIe node or the SATA node in the device tree blob. This + patch removes the unnecessary and even confusing warning, when the node + is not found at all. + + Signed-off-by: Stefan Roese + +commit 6e24a1eb1490aa043770bcf0061ac1fad0864fd9 +Author: Remy Bohmer +Date: Fri Sep 19 13:30:06 2008 +0200 + + Add missing device types to dev_print() in part.c + + Signed-off-by: Remy Bohmer + +commit 5fdc215f0b351b0c36cc3f8a0fa5850f24454bed +Author: Wolfgang Denk +Date: Mon Sep 22 22:23:06 2008 +0200 + + Fix DPRAM memory leak when CFG_ALLOC_DPRAM is defined, which + eventually leads to a machine check. This change assures that DPRAM + is allocated only once in that case. + + Signed-off-by: Gary Jennejohn + Signed-off-by: Wolfgang Denk + +commit a07faf7b9ad5a86763a577c79922c4ff9a70ef23 +Author: Laurent Pinchart +Date: Wed Sep 17 17:57:34 2008 +0200 + + Fix Spartan-3 definitions. + + A few Spartan-3 definitions erroneously use Spartan-3E size + constants. This patch fixes them. + + Signed-off-by: Laurent Pinchart + +commit 28113e1f0da4146b823ffce37680d31d5685a60b +Author: Laurent Pinchart +Date: Wed Sep 17 17:41:58 2008 +0200 + + Remove duplicate Spartan-3E definition. + + Signed-off-by: Laurent Pinchart + Signed-off-by: Wolfgang Denk + +commit 5c65ecf7cd94df250b295621f3b24135cbcfe579 +Author: Anatolij Gustschin +Date: Wed Sep 17 13:46:17 2008 +0200 + + socrates: change default mtest address range + + Running mtest command on socrates without specifying + an address range crashes the board. This patch changes + default mtest address range to prevent this behavior. + + Signed-off-by: Anatolij Gustschin + +commit d666b2d59674b5e002c0821b7ab83ec3ff90d670 +Author: Anatolij Gustschin +Date: Wed Sep 17 12:34:45 2008 +0200 + + socrates: fix crash after relocation + + Currently U-Boot crashes after relocation to RAM. + Changing the CPO value of the DDR SDRAM TIMING_CFG_2 + register to READ_LAT + 1 (to the value it was before + conversion of socrates to new DDR code) fixes the + problem. + + Signed-off-by: Anatolij Gustschin + +commit 562788b0a303f3528b920d81f547f5ca77ba528e +Author: Anatolij Gustschin +Date: Wed Sep 17 11:45:51 2008 +0200 + + socrates: fix SPD EEPROM address + + Commit be0bd8234b9777ecd63c4c686f72af070d886517 + changed SPD EEPROM address to 0x51 and DDR SDRAM + detection stopped working. Change this address + back to 0x50. + + Signed-off-by: Anatolij Gustschin + +commit 023824549a370bd185d7129d9a6c86f9be7b86a8 +Author: Stefan Roese +Date: Mon Sep 22 11:06:50 2008 +0200 + + Revert "ppc4xx: Fix DDR2 auto calibration on Kilauea 600MHz (200MHz PLB)" + + This reverts commit 3eec160a3a405b29ce9c06920f6427b9047dd8a8. + + Signed-off-by: Stefan Roese + +commit b5d10a13525c07ec6374adf840d7c87553b5f189 +Author: Nobuhiro Iwamatsu +Date: Thu Sep 18 19:34:36 2008 +0900 + + sh: Fix compile warning + + Signed-off-by: Nobuhiro Iwamatsu + +commit 4a065abf926f128beb36d93449defa0d690e7fef +Author: Nobuhiro Iwamatsu +Date: Thu Sep 18 19:04:26 2008 +0900 + + sh: Add support watchdog for SH4A core + + Add support watchdog for SH4A core (SH7763, SH7780 and SH7785). + And fix some compile warning. + + Signed-off-by: Nobuhiro Iwamatsu + +commit a03c09c5fdb8430fe2ae6a03f88a0cf7bcc0aa57 +Author: Nobuhiro Iwamatsu +Date: Wed Sep 17 11:45:26 2008 +0900 + + sh: Fix typo in SH serial driver + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 6b44a439215ba7c63f666f8099213ea4f05f2b07 +Author: Nobuhiro Iwamatsu +Date: Wed Sep 17 11:08:36 2008 +0900 + + sh: Add support any page size and empty_zero_page to SH Linux uImage + + Old U-Boot supported 4KB page size only. If this version, Linux + kernel can not get command line from U-Boot. + SH Linux kernel can change page size and empty_zero_page. + This patch support this function and fix promlem. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit ce9f99ddb59628f41dc534e892368a7d66dfc774 +Author: Nobuhiro Iwamatsu +Date: Thu Aug 28 13:40:52 2008 +0900 + + sh: rsk7203: Add support pkt_data_pull and pkt_data_push function + + Add function of smc911x, pkt_data_pull and pkt_data_push. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit dd820b03a2f45e86e7960e26729a3b58e3dda44a +Author: Wolfgang Denk +Date: Thu Sep 18 13:57:32 2008 +0200 + + ADS5121: fix typo in "rootpath" default setting + + Signed-off-by: Wolfgang Denk + +commit 87b4ef560cf2da4ccc9e59711ad1ff7fafe96670 +Author: Wolfgang Denk +Date: Wed Sep 17 10:17:55 2008 +0200 + + Coding style cleanup; update CHANEGLOG + + Signed-off-by: Wolfgang Denk + +commit 3eec160a3a405b29ce9c06920f6427b9047dd8a8 +Author: Victor Gallardo +Date: Tue Sep 16 06:59:13 2008 -0700 + + ppc4xx: Fix DDR2 auto calibration on Kilauea 600MHz (200MHz PLB) + + Signed-off-by: Victor Gallardo + Signed-off-by: Adam Graham + Signed-off-by: Stefan Roese + +commit ce47eb402c5e29a025399dc282246414fc492940 +Author: Peter Tyser +Date: Tue Sep 16 10:04:47 2008 -0500 + + Support for multiple SGMII/TBI interfaces for TSEC ethernet + + Fix TBI PHY accesses to use the proper offset in CPU register space. The + previous code would incorrectly access the TBI PHY by reading/writing to CPU + register space at the same location as would be used to access external PHYs. + + Signed-off-by: Peter Tyser + Acked-by: Andy Fleming + +commit 7c803be2eb3cae245dedda438776e08fb122250f +Author: Wolfgang Denk +Date: Tue Sep 16 18:02:19 2008 +0200 + + TQM8xx: Fix CFI flash driver support for all TQM8xx based boards + + After switching to using the CFI flash driver, the correct remapping + of the flash banks was forgotten. + + Also, some boards were not adapted, and the old legacy flash driver + was not removed yet. + + Signed-off-by: Wolfgang Denk + +commit c0d2f87d6c450128b88e73eea715fa3654f65b6c +Author: Wolfgang Denk +Date: Sun Sep 14 00:59:35 2008 +0200 + + Prepare v2008.10-rc2 + + Signed-off-by: Wolfgang Denk + +commit f12e4549b6fb01cd2654348af95a3c7a6ac161e7 +Author: Wolfgang Denk +Date: Sat Sep 13 02:23:05 2008 +0200 + + Coding style cleanup, update CHANGELOG + + Signed-off-by: Wolfgang Denk + +commit 0c32565f536609d78feef35c88bbc39d3ac53a73 +Author: Peter Tyser +Date: Wed Sep 10 09:18:34 2008 -0500 + + Update mailing list email and archive addresses + + Signed-off-by: Peter Tyser + +commit fb661ea444ae61de60520f66ae84cdb5dd5a3246 +Author: u-boot@bugs.denx.de +Date: Thu Sep 11 15:40:01 2008 +0200 + + 85xx: socrates: autoprobe Lime chip + + This patch is an attempt to implement autoprobing for the Lime + presence on the bus. + Configure GPCM for Lime CS2 and try to access chip ID registers. + Second read atempt delivers register values if the chip is present. + + Signed-off-by: Anatolij Gustschin + +commit e99b607a5ec56ce66e0bcccb78480d5e16fb7bc5 +Author: u-boot@bugs.denx.de +Date: Thu Sep 11 15:40:01 2008 +0200 + + 85xx: socrates: Add support for new image format. + + Signed-off-by: Detlev Zundel + +commit 3c094b652d4107b34641f300a8e9fe16ca15e3d8 +Author: Nobuhiro Iwamatsu +Date: Thu Sep 11 17:28:18 2008 +0900 + + sh: Fix compile error for r2dplus + + netdev.h was not include by r2dplus. + + Signed-off-by: Nobuhiro Iwamatsu + +commit 56844a22b76c719e600047e23b80465a44d76abd +Author: Heiko Schocher +Date: Thu Sep 11 08:11:23 2008 +0200 + + powerpc: Fix bootm to boot up again with a Ramdisk + + Commit 2a1a2cb6 didnt remove the dummy mem reservation in fdt_chosen, + and this stopped Linux from booting with a Ramdisk. This patch fixes + this, by deleting the useless dummy mem reservation. + + When booting with a Ramdisk, a fix offset FDT_RAMDISK_OVERHEAD is now + added to of_size, so we dont need anymore a dummy mem reservation. + + I measured the value of FDT_RAMDISK_OVERHEAD on a MPC8270 based + system (=0x44 bytes) and rounded it up to 0x80). + + Signed-off-by: Heiko Schocher + Acked-by: Kumar Gala + +commit fc9c1727b5b3483ce49c3cb668e8332fb001b8a7 +Author: Luigi 'Comio' Mantellini +Date: Mon Sep 8 02:46:13 2008 +0200 + + Add support for LZMA uncompression algorithm. + + Signed-off-by: Luigi 'Comio' Mantellini + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0008b6d968160abe2bfd936493f3a516a7c8da20 +Author: Anton Vorontsov +Date: Fri Jun 27 23:04:20 2008 +0400 + + fsl_elbc_nand: ecclayout cleanups + + This patch deletes oobavail assignments, they're calculated by the nand + core code in nand_scan_tail, plus current oobavail values are wrong for + the LP NANDs. + + Signed-off-by: Anton Vorontsov + Signed-off-by: David Woodhouse + Signed-off-by: Scott Wood + +commit 8f42bf1c393d53a70c2545e9f329d11c46d74794 +Author: Anton Vorontsov +Date: Fri Jun 27 23:04:13 2008 +0400 + + fsl_elbc_nand: implement support for flash-based BBT + + This patch implements support for flash-based BBT for chips working + through ELBC NAND controller, so that NAND core will not have to re-scan + for bad blocks on every boot. + + Because ELBC controller may provide HW-generated ECCs we should adjust + bbt pattern and bbt version positions in the OOB free area. + + Signed-off-by: Anton Vorontsov + Signed-off-by: David Woodhouse + Signed-off-by: Scott Wood + +commit 97ae023648e764f794ffb9c52da109d6caf09c47 +Author: Anton Vorontsov +Date: Fri Jun 27 23:04:04 2008 +0400 + + fsl_elbc_nand: fix OOB workability for large page NAND chips + + For large page chips, nand_bbt is looking into OOB area, and checking + for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be + reserved for bbt means. + + But ELBC driver is specifying ecclayout so that oobfree area starts at + offset 1, so only one byte left for the bbt purposes. + + This causes problems with any OOB users, namely JFFS2: after first mount + JFFS2 will fill all OOBs with "erased marker", so OOBs will contain: + + OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff + OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff + OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff + OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff + + And on the next boot, NAND core will rescan for bad blocks, then will + see "0xff 0x19" pattern, and will mark all blocks as bad ones. + + To fix the issue we should implement our own bad block pattern: just one + byte at OOB start. Though, this will work only for x8 chips. For x16 + chips two bytes must be checked. Since ELBC driver does not support x16 + NANDs (yet), we're safe for now. + + Signed-off-by: Anton Vorontsov + Signed-off-by: David Woodhouse + Signed-off-by: Scott Wood + +commit 7238ada313057a85409485b8ee21515dc10c07a5 +Author: Wolfgang Denk +Date: Fri Sep 12 13:52:21 2008 +0200 + + MPC512x: reduce timeout waiting for Ethernet autonegotiation to 2.5s + + Signed-off-by: Wolfgang Denk + +commit b18410e508a12ba0a177dfc2a386857c806fa96d +Author: Stefan Roese +Date: Thu Sep 11 13:05:56 2008 +0200 + + ppc4xx: Enable device tree (FDT) support in zeus board port + + Signed-off-by: Stefan Roese + +commit 7bf5ecfa50722a9feb45ea8f04da75f5d406f20b +Author: Stefan Roese +Date: Wed Sep 10 16:53:47 2008 +0200 + + ppc4xx: Fix SDRAM inititialization of multiple 405 based board ports + + This patch fixes a problem introdiced with patch + bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by + initdram()]. + + The boards affected are: + - PCI405 + - PPChameleonEVB + - quad100hd + - taihu + - zeus + + Signed-off-by: Stefan Roese + +commit 61737c59a3285f6fadf96a5836879898c04ec28d +Author: Ricardo Ribalda Delgado +Date: Thu Sep 11 19:41:26 2008 -0400 + + ppc4xx: Add .gitignore file to xilinx-ppc440 boards + + Signed-off-by: Ricardo Ribalda Delgado + Signed-off-by: Stefan Roese + +commit 2bec498ed1164a58cd8437b561bdc4551d69f9bf +Author: Ricardo Ribalda Delgado +Date: Thu Sep 11 19:41:25 2008 -0400 + + ppc4xx: Fix compilation of v5fx30teval_flash + + Signed-off-by: Ricardo Ribalda Delgado + Signed-off-by: Stefan Roese + +commit 4bed9deebbd7ee6f0ba746b44d47a922156f7404 +Author: Ricardo Ribalda Delgado +Date: Wed Sep 10 17:44:30 2008 -0400 + + ppc4xx: Fix in-tree build for ppc440-generic boards + + Signed-off-by: Ricardo Ribalda Delgado + Signed-off-by: Stefan Roese + +commit 06c4ab50f5ccfb55ea2dd324aa28b2b06102e416 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Sep 12 02:20:47 2008 +0200 + + ARM: synchronize mach-types.h with linux 2.6.27-rc6 + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 3ee9f03f588ad605e3fd10530237f9e3e2e7ab4c +Author: Jens Scharsig +Date: Fri Sep 12 02:20:47 2008 +0200 + + at91rm9200: fix errors with CONFIG_CMD_I2C_TREE + + This patch prevents linker error on AT91RM9200 boards, if + CONFIG_CMD_I2_TREE is set. + It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function. + + Signed-off-by: Jens Scharsig + +commit b5b0344957d32e3d07a8dd72fce64fb48e680ba4 +Author: Hugo Villeneuve +Date: Fri Sep 12 02:20:47 2008 +0200 + + ARM DaVinci: Remove duplicate code in cpu/arm926ejs/davinci/dp83848.c + + ARM DaVinci: Remove duplicate code in cpu/arm926ejs/davinci/dp83848.c + + Signed-off-by: Hugo Villeneuve + +commit 03db53335c8eba656a7c44d1555b1a4514383e33 +Author: Shinya Kuribayashi +Date: Fri Sep 12 02:20:46 2008 +0200 + + make: Remove redundant __ARM__ addition when cross-compiling on *BSD + + __ARM__ is given by arm_config.mk automatically. + + Signed-off-by: Shinya Kuribayashi + +commit 8cc62a7d9c77f8ef5166fb57322c4a6ddac320b4 +Author: Claudio Scordino +Date: Fri Sep 12 02:20:46 2008 +0200 + + Fix MACH_TYPE for the AT91RM9200DK board. + + Signed-off-by: Claudio Scordino + +commit 274737e5eb25b2bcd3af3a96da923effd543284f +Author: Andrew Dyer +Date: Fri Sep 12 02:20:46 2008 +0200 + + i.mx change get_timer(base) to return time since base + + This patch changes get_timer() for i.MX to return the time since + 'base' instead of the time since the counter was at zero. + + Symptom seen is flash timeout errors when erasing or programming a + sector using the common cfi flash code. + + Signed-off-by: Andrew Dyer + +commit 48fed40575b3e8eae960eb0141509ddd9a73012a +Author: Andrew Dyer +Date: Fri Sep 12 02:20:46 2008 +0200 + + i.MX use u-boot baud rate and don't assume UART master clock + + 1) Change the i.MX serial driver to use the baud rate set in the + u-boot environment + + 2) don't assume a 16MHz value for PERCLK1 in baud rate calculations + + 3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write + one to clear" like other status bits in the reg.) + + Signed-off-by: Andrew Dyer + +commit 6e1551a870d360805b9d172dc56d935064abe71d +Author: Andrew Dyer +Date: Fri Sep 12 02:20:46 2008 +0200 + + arm920t fix constant error in start.S + + Code in cpu/arm920t/start.S will die with a compilation error if + CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for + the ARM sub instruction. Change the code so that each is subtracted + independently to avoid the error. + + Signed-off-by: Andrew Dyer + +commit b23253835f871cd9bd8e955b9a971d18a7d4ff56 +Author: Gururaja Hebbar K R +Date: Fri Sep 12 02:20:40 2008 +0200 + + ARM OMAP : Correct Invalid Timer Register Field Declaration in omap1510.h & omap730.h + + - Correct Invalid #define of MPUTIM_PTV_MASK for + omap1510 & omap730 register definition + + MPUTIM_PTV_MASK is defined as + #define MPUTIM_PTV_MASK (0x7< + +commit c455d07396dddc9864fd8dbb965ee10fe95ce8cf +Author: Adrian Filipi +Date: Fri Jul 18 11:52:02 2008 -0400 + + Set up SD/MMC OCR as comment describes. i.e. 3.2-3.4v. + + Signed-off-by: Adrian Filipi + +commit eb16135df20535b0d19969f50fb5bd17f95e9c25 +Author: Guennadi Liakhovetski +Date: Thu Aug 28 12:25:11 2008 +0200 + + i.MX31: document timer precision option + + Signed-off-by: Guennadi Liakhovetski + +commit 1a6337b01351b82a45b0defa76f08744511c580b +Author: Magnus Lilja +Date: Fri Aug 29 10:36:18 2008 +0200 + + i.MX31: Make the SPI bus and chip select configurable for MC13783 + + The i.MX31 has three SPI buses and each bus has several chip selects + and the MC13783 chip can be connected to any of these. The current + RTC driver for MC13783 is hardcoded for CSPI2/SS2. + + This patch makes make MC13783 SPI bus and chip select configurable + via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS. + + Signed-off-by: Magnus Lilja + +commit 8c4ebec25b21e355b8488698ec1594da9701fff4 +Author: Magnus Lilja +Date: Fri Aug 29 10:36:17 2008 +0200 + + i.MX31: Add reset_timer() and modify get_timer_masked(). + + This patch adds the reset_timer() function (needed by nand_base.c) and + modifies the get_timer_masked() to work in the same way as the omap24xx + function. + + Signed-off-by: Magnus Lilja + +commit deeec4991a55de243787002ede24d2331d234fc8 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:09 2008 +0200 + + ap325rxa: remove duplicate CONFIG_FLASH_CFI_DRIVER + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit a3a08c0cedd329edf5256e1d6b2bad0fca002725 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:09 2008 +0200 + + bootm arm/avr32/blackfin/microblaze/nios2/sh: remove no more need 'error' label + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0e8d158664a913392cb01fb11a948d83f72e105e +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:06 2008 +0200 + + rename CFG_ENV macros to CONFIG_ENV + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 1ede78710c3bf9ad6f4a53aaddc3bcc86fedd9df +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:05 2008 +0200 + + nvedit: rename error comment to CONFIG_ENV_IS_IN_ + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit b64b775e7546ed138df360ceb3a71ee358cb9a01 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:05 2008 +0200 + + cmd_mem: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 8a40fb148efa442d6526eac46a2001e4c64d28ff +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:05 2008 +0200 + + move cmd_get_data_size to command.c + + add CMD_DATA_SIZE macro to enable it + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 507641d2491980531932b9f25dab37fe5e6c3a1a +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:04 2008 +0200 + + env_flash: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 5a1aceb0689e2f731491838970884a673ef7e7d3 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:04 2008 +0200 + + rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 7d9b5bae5ba558c7464d89d033aca04acaf01172 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:03 2008 +0200 + + cleanup use of CFG_ENV_IS_IN_FLASH + + - #if CFG_ENV_IS_IN_FLASH + - #if (CFG_ENV_IS_IN_FLASH == 1) + - #define CFG_ENV_IS_IN_FLASH 0 + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0cf4fd3cf8d0e00605bec5fc56f89c6415015a46 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:01 2008 +0200 + + rename environment.c in env_embedded.c to reflect is functionality + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit c0878af6e32f0fd8e13a6ca315b9add64441115a +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:01 2008 +0200 + + env_nowhere: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 93f6d72544da4510a146bc4c93d609b0116cde37 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:00 2008 +0200 + + rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHERE + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 2556ef78113b5f089dfcac5da90bf31dd568397b +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:00 2008 +0200 + + env_sf: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0b5099a8419bf9c828df5e3e2c6878dc300d98e3 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:00 2008 +0200 + + rename CFG_ENV_IS_IN_SPI_FLASH in CONFIG_ENV_IS_IN_SPI_FLASH + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 55c5f49910ec8225347aa1d211352a84de6649b4 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:48:00 2008 +0200 + + env_onenand: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 9656138ff1a34d4c4768db6b490deffc40ee674b +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:59 2008 +0200 + + rename CFG_ENV_IS_IN_ONENAND in CONFIG_ENV_IS_IN_ONENAND + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 957a0e69575683efd70ace147746bbb3d8e7c501 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:59 2008 +0200 + + env_nvram: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 9314cee6917444ab88bd4e758da7a30975120187 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:59 2008 +0200 + + rename CFG_ENV_IS_IN_NVRAM in CONFIG_ENV_IS_IN_NVRAM + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 06f61354397911a4c121dfa51b6ccbf7e300d48b +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:59 2008 +0200 + + env_nand: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 51bfee192099206a4397f15f3b93516e01f58ab0 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:58 2008 +0200 + + rename CFG_ENV_IS_IN_NAND in CONFIG_ENV_IS_IN_NAND + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit d8cc04d0ac9c7c0d12454708aaf5489f8532bbf9 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:58 2008 +0200 + + env_dataflash: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 057c849c45b9ee19df8ff3acdeee66be52819962 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:58 2008 +0200 + + rename CFG_ENV_IS_IN_DATAFLASH in CONFIG_ENV_IS_IN_DATAFLASH + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit d1034bc8db60fa6bd419328baf6a75cb0645cee8 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Sep 10 22:47:52 2008 +0200 + + cmd_eeprom: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit bf5a7710ec70e90e98f451b4ba0eb65f9ffc34eb +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Sep 5 09:19:54 2008 +0200 + + env_eeprom: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit bb1f8b4f8bb0bfce52e0faa4637b975b745824b3 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Sep 5 09:19:30 2008 +0200 + + rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROM + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 32628c5008105a732212003d83b75f05e5243bb2 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Aug 30 23:54:58 2008 +0200 + + cmd_mac: Move conditional compilation to Makefile + + finish remaning CFG_ID_EEPROM in CONFIG_ID_EEPROM + start in commit ad8f8687b78c3e917b173f038926695383c55555 + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit e5648acab153f0f429bfc714902c5aaa7879f71b +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Aug 30 23:47:41 2008 +0200 + + cmd_fdc: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 2d02d91d530e831f2dab228085963fc1d5b71cb0 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Aug 30 23:47:38 2008 +0200 + + common/Makefile: add core command section + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0d92d4a699fb1a39381d98571dc51fb97e5bcf9e +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Aug 30 23:29:57 2008 +0200 + + cmd_vfd: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 6644641d072aee3087da129d8443187196a4d8a9 +Author: Scott Wood +Date: Wed Sep 10 11:48:49 2008 -0500 + + delta, zylonite: Update nand_oobinfo to nand_ecclayout. + + This is part of the switch to newer upstream MTD code. + + Signed-off-by: Scott Wood + +commit 9b05aa788bfdd3264ff1bc9418cb19550a7234e4 +Author: Hugo Villeneuve +Date: Sat Aug 30 17:06:55 2008 -0400 + + ARM DaVinci: Fix broken HW ECC for large page NAND. + + Based on original patch by Bernard Blackham + + U-boot's HW ECC support for large page NAND on Davinci is completely + broken. Some kernels, such as the 2.6.10 one supported by + MontaVista for DaVinci, rely upon this broken behaviour as they + share the same code for ECCs. In the existing scheme, error + detection *might* work on large page, but error correction + definitely does not. Small page ECC correction works, but the + format is not compatible with the mainline git kernel. + + This patch adds ECC code that matches what is currently in the + Davinci git repository (since NAND support was added in 2.6.24). + This makes the ECC and OOB layout written by u-boot compatible with + Linux for both small page and large page devices and fixes ECC + correction for large page devices. + + The old behaviour can be restored by defining the macro + CFG_DAVINCI_BROKEN_ECC, which is undefined by default. + + Signed-off-by: Hugo Villeneuve + Acked-by: Sergey Kubushyn + Signed-off-by: Scott Wood + +commit 0b7c5639891f4103a0e31ec7ae0beb3e97ed3836 +Author: Heiko Schocher +Date: Wed Sep 10 11:15:28 2008 +0200 + + muas3001: update BR4 settings + + Also set up the port pins for using I2C. + + Signed-off-by: Heiko Schocher + +commit 3591293509e0c0bcf244b0f974775bff2e25697e +Author: Petri Lehtinen +Date: Wed Sep 10 09:43:49 2008 +0300 + + autoscr: Fix one-character lines and non-newline terminated scripts + + When not using hush, the autoscr command now executes lines that are + only one character long. It also runs the last line of scripts even if + it does not end in a newline. + + Signed-off-by: Petri Lehtinen + +commit 9ebbb54f7a25055010fa6668eba40c72a4c4f985 +Author: Victor Gallardo +Date: Tue Sep 9 15:13:29 2008 -0700 + + ppc4xx: Allow DTT_I2C_DEV_CODE configured by CFG_I2C_DTT_ADDR + + On AMCC Arches board DTT_I2C_DEV_CODE is different then canyonlands + and glacier. + + Signed-off-by: Victor Gallardo + +commit 245f6ef3e11828cb46188e396fb1e67f7b07cd03 +Author: Heiko Schocher +Date: Mon Sep 8 10:21:11 2008 +0200 + + muas3001: added support for the LM75 sensor. + + Signed-off-by: Heiko Schocher + +commit 4a02a2dca82aeab8f839db9dd35fda9d5412dacb +Author: Heiko Schocher +Date: Mon Sep 8 10:20:19 2008 +0200 + + muas3001: activate WDT for the muas3001 board. + + Signed-off-by: Heiko Schocher + +commit a55d074dac24dc941f1afb5b4e94b1509bfdda4e +Author: Heiko Schocher +Date: Mon Sep 8 10:19:36 2008 +0200 + + muas3001: added 64MB SDRAM autodetection. + + Signed-off-by: Heiko Schocher + +commit 5251469943895de4bb9a04d5053352cc22acb7d5 +Author: Andrew Klossner +Date: Thu Aug 21 07:12:26 2008 -0700 + + Fix printf errors under -DDEBUG + + Fix printf format-string/arg mismatches under -DDEBUG. + + These warnings occur with DEBUG defined for a platform using + cpu/mpc85xx. Users of other architectures can unearth similar + problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right + after "CFLAGS += $(call cc-option,-fno-stack-protector)". + + Signed-off-by: Andrew Klossner + Signed-off-by: Andy Fleming + +commit 8b9e4787641719d709bfa2ebeb72e8bd4952bee7 +Author: Wolfgang Denk +Date: Tue Sep 9 23:55:18 2008 +0200 + + Update CHANGELOG, prepare 2008-10-rc1 release + + Signed-off-by: Wolfgang Denk + +commit e0ff3d350d6b7960deb5a881dfc5acf3a63ef676 +Author: Kumar Gala +Date: Mon Sep 8 08:51:29 2008 -0500 + + 85xx: Ensure timebase is zero on secondary cores + + The e500um says the timebase is volatile out of reset. To ensure + TB sync works we need to make sure its zero. + + Signed-off-by: Kumar Gala + +commit 54b4ab3c961a2012a1c2a09c259a6343323ec551 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 9 22:18:24 2008 +0200 + + bootm_load_os: fix load_end debug message + + print load_end value not pointer + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 1d9af0be764960e6cc1c093e97176c3542796820 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 9 22:18:23 2008 +0200 + + bootm: enable fdt support only on ppc, m68k and sparc + + ...as done in image.c + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 748b5274e76f81df85cfcffaffedc323678d0623 +Author: Markus Heidelberg +Date: Tue Sep 9 18:51:05 2008 +0200 + + common/cmd_mem.c: remove nested #if defined(CONFIG_CMD_MEMORY) + + Signed-off-by: Markus Heidelberg + +commit 650632fe4ca09cfd0e5e6a593f2efc02ef87a58c +Author: Markus Heidelberg +Date: Tue Sep 9 17:31:46 2008 +0200 + + gitignore: add tags files and Vim swap file + + Signed-off-by: Markus Heidelberg + +commit 1d9b67b23fca6a25154333733204339802510720 +Author: Yoshihiro Shimoda +Date: Tue Sep 9 17:52:47 2008 +0900 + + add board_eth_init() for sh7785lcr board + + Fix the problem that cannot work RTL8169 on sh7785lcr board. + + Signed-off-by: Yoshihiro Shimoda + +commit 7b7a869a8ba3bd6d9bffb748c91232141330f514 +Author: TsiChung Liew +Date: Wed Aug 6 16:08:41 2008 -0500 + + mtd: SPI Flash: Support the STMicro Flash + + Add MTD SPI Flash support for M25P16, M25P20, M25P32, + M25P40, M25P64, M25P80, M25P128. + + Signed-off-by: Jason McMullan + Signed-off-by: TsiChung Liew + +commit 4bc07c368076560ed7fa4c9f987c71a8521488a9 +Author: Wolfgang Denk +Date: Tue Sep 9 17:55:31 2008 +0200 + + trab: fix build problem after change to use do_div() + + We must link with libgeneric now. + + Signed-off-by: Wolfgang Denk + +commit 3b20fd83c73c22acfcb0c6663be747bd5c8b7011 +Author: Ryan CHEN +Date: Wed Aug 20 13:00:17 2008 -0400 + + Correct drv_usb_kbd_init function + + The patch is that check if usb_get_dev_index() function return valid + pointer. If valid, continue. Otherwise return -1. + + Signed-off-by: Ryan Chen + Acked-by: Markus Klotzbuecher + +commit eba1f2fc75f128a9a6c1328d786996a93fd7a707 +Author: Remy Bohmer +Date: Wed Aug 20 11:22:02 2008 +0200 + + Make usb-stop() safe to call multiple times in a row. + + A recent commit (936897d4d1365452bbbdf8430db5e7769ef08d38) + enabled the usb_stop() command in common/cmd_bootm.c which was + not enabled for some time, because no board did actually set the + CFG_CMD_USB flag. So, now the usb_stop() is executed before + loading the linux kernel. + + However, the usb_ohci driver hangs up (at least on AT91SAM) if the + driver is stopped twice (e.g. the peripheral clock is stopped on AT91). + If some other piece of code calls usb_stop() before the bootm command, + this command will hangup the system during boot. + (usb start and stop is typically used while booting from usb memory stick) + + But, stopping the usb stack twice is useless anyway, and a flag already + existed that kept track on the usb_init()/usb_stop() calls. + So, we now check if the usb stack is really started before we stop it. + + This problem is now fixed in both the upper as low-level layer. + + Signed-off-by: Remy Bohmer + Acked-by: Markus Klotzbuecher + +commit 2c8ccf2728f5e67d991cecf76c4057db75a87b67 +Author: Wolfgang Denk +Date: Tue Sep 9 16:55:47 2008 +0200 + + Makefile: fix bug introduced by commit 47ffd6c2 + +commit 880f6a5d7596f42db5ff8803b797b78ec5b146e0 +Author: Ricardo Ribalda Delgado +Date: Tue Sep 9 10:00:33 2008 -0400 + + ppc4xx: ppc440-generic-ALL: Fix out of tree build v2 + + This patch solves the problems compiling ml507, v5fx30teval and + ppc440-generic out of tree. + + Signed-off-by: Ricardo Ribalda Delgado + +commit 47bebe34ca4e33bab0e822e4ceebbec2590ccbcb +Author: Nícolas Carneiro Lebedenco +Date: Thu Sep 4 15:35:46 2008 -0300 + + Fix dev_print when called from usb_stor_info (usb storage command) + + Fix output of the usb storage command. It was printing "Device 0: not + available" because IF_TYPE_USB was not included into the switch + statement. + + Signed-off-by: Nicolas Lebedenco + +commit a4f243452cc8ce0c2c9b51a2520db4bde5f472de +Author: Bartlomiej Sieka +Date: Tue Sep 9 12:58:16 2008 +0200 + + FIT: make iminfo check hashes of all images in FIT, return 1 on failed check + + Signed-off-by: Bartlomiej Sieka + +commit 919f550dc11a13abf01c6bc713c968de790b8d7c +Author: Bartlomiej Sieka +Date: Tue Sep 9 12:58:15 2008 +0200 + + FIT: add ability to check hashes of all images in FIT, improve output + + - add function fit_all_image_check_hashes() that verifies if all + hashes of all images in the FIT are valid + - improve output of fit_image_check_hashes() when the hash check fails + + Signed-off-by: Bartlomiej Sieka + +commit 1de1fa408967cef6804bb046b904114519bb36f0 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Sep 8 20:54:39 2008 +0200 + + qemu_mips: Update linux bootm to support dynamic cmdline + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit f5ed9e39088ecfa5a5f3ef47b08e5bda7890d764 +Author: Peter Tyser +Date: Mon Sep 8 14:56:49 2008 -0500 + + Add support for booting of INTEGRITY operating system uImages + + Signed-off-by: Peter Tyser + +commit 72f1b65f1b68bc6ed0d182eda1f3d6cf51b6414a +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Sep 8 21:01:29 2008 +0200 + + mips/bootm: Fix typo in commit c4f9419c, "initrd_start" replaced by "images->rd_start" + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 9ba2e2c8191353d75b2d535e672a125be7b84c03 +Author: Kumar Gala +Date: Mon Sep 8 13:57:12 2008 -0500 + + Remove support for booting ARTOS images + + Pantelis Antoniou stated: + AFAIK, it is still used but the products using PPC are long gone. + Nuke it plz (from orbit). + + So remove it since it cleans up a usage of env_get_char outside of + the environment code. + + Signed-off-by: Kumar Gala + +commit 47ffd6c2fc72b46daa9d5d59eedb894fab2b7ee1 +Author: Wolfgang Denk +Date: Tue Sep 9 15:45:18 2008 +0200 + + Makefile: compile and link each module just once + + Several source files need to be compiled and linked when one or more + config options are selected. To allow for easy selection in the + Makefiles yet to avoild multiple compilation (which costs build time) + and especially multiple linking (which causes errors), we use + "COBJS = $(sort COBJS-y)" which eliminates duplicates. + + By courtesy of Detlev Zundel who suggested this approach. + + Signed-off-by: Wolfgang Denk + +commit 48d0192fe869948fef14b460b5f0c85bca933693 +Author: Andreas Engel +Date: Mon Sep 8 14:30:53 2008 +0200 + + Moved conditional compile into Makefile + + Signed-off-by: Andreas Engel + +commit 20c9226cb8cab08a111ee73db04e62d943ee0c97 +Author: Andreas Engel +Date: Mon Sep 8 10:17:31 2008 +0200 + + Merged serial_pl010.c and serial_pl011.c. + + They only differ in the init function. + This also adds the missing watchdog support for the PL011. + + Signed-off-by: Andreas Engel + +commit 0817d688f307ee2c0598e79175c94a40ce90337b +Author: Ricardo Ribalda Delgado +Date: Sun Sep 7 17:10:27 2008 -0400 + + Remove gap fill in srec object v2 + + SREC files do not need gap fill: The load address is specified in the + file. On the other hand, it can't be avoided in a .bin object. It has + no information about memory location. + + Signed-off-by: Ricardo Ribalda Delgado + +commit 1dc306931ca5ce87f13916fa7165b052d3aa714f +Author: Markus Heidelberg +Date: Sun Sep 7 20:18:27 2008 +0200 + + README: fix missing subdirectory in the documentation + + Signed-off-by: Markus Heidelberg + +commit 3ef96ded38a8d33b58b9fab9cd879d51ddac4cbd +Author: Graeme Russ +Date: Sun Sep 7 07:08:42 2008 +1000 + + Update i386 code (sc520_cdp) + + Attempt to bring i386 / sc520 inline with master + + Signed-off-by: Graeme Russ + +commit 5608692104efa8d56df803dc79ea41ac3607eee5 +Author: Guennadi Liakhovetski +Date: Thu Sep 4 13:01:49 2008 +0200 + + fw_env: add NAND support + + Add support for environment in NAND with automatic NOR / NAND recognition, + including unaligned environment, bad-block skipping, redundant environment + copy. + + Signed-off-by: Guennadi Liakhovetski + +commit dd794323a2a1ed6a8a5df51785c31bcde60ad7ca +Author: Matthias Fuchs +Date: Tue Sep 9 09:50:24 2008 +0200 + + ppc4xx: Fix out-of-tree building of CPCI405 variants + + Signed-off-by: Matthias Fuchs + Acked-by: Stefan Roese + +commit 59f630588e3fdbd698a0a2798e52a8924e899563 +Author: Sergei Poselenov +Date: Fri Aug 15 15:42:11 2008 +0200 + + Removed hardcoded MxMR loop value from upmconfig() for MPC85xx. + + Signed-off-by: Sergei Poselenov + +commit e64987a892353f3d49eb242d997820ef8f538912 +Author: Anatolij Gustschin +Date: Fri Aug 15 15:42:13 2008 +0200 + + 85xx: socrates: Enable Lime support. + + This patch adds Lime GDC support together with support for the PWM + backlight control through the w83782d chip. The reset pin of the + latter is attached to GPIO, so we need to reset it in + early_board_init_r. + + Signed-off-by: Anatolij Gustschin + +commit 3e79b588b5199f35016f178fc0d5d1266382097f +Author: Detlev Zundel +Date: Fri Aug 15 15:42:12 2008 +0200 + + 85xx: Socrates: Major code update. + + - Update the local bus ranges in the FDT for Linux for the various + devices connected to the local bus via chip-select. + + - Set the LCRR_DBYP bit in the LCRR for local bus frequencies + lower than 66 MHz and uses I/O accessor functions consequently. + + - UPM data update. + + - Update of default environment and configuration. Use I2C multibus + as we do have two I2C buses. Also enable sdram and ext2 commands. + + Signed-off-by: Wolfgang Grandegger + Signed-off-by: Sergei Poselenov + Signed-off-by: Detlev Zundel + +commit e8d18541c6ceab821f75faab031740b33fdbfa4b +Author: Timur Tabi +Date: Fri Jul 18 16:52:23 2008 +0200 + + Update Freescale 85xx boards to sys_eeprom.c + + The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID + format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale + 86xx boards already use sys_eeprom.c, so this patch migrates the remaining + Freescale 85xx boards to use it as well. cds_eeprom.c is deleted. + + Signed-off-by: Timur Tabi + +commit aab2bf0202c86227e3dcc8a5b58946087ebcc1af +Author: Wolfgang Denk +Date: Tue Sep 9 10:08:02 2008 +0200 + + lib_ppc/interrupts.c: make board_show_activity() a weak function + + This allows to use show_activity() without having to + define an empty board_show_activity() function. + + Signed-off-by: Wolfgang Denk + +commit fe876787f8743883ce58fed61525eaa2f34da4c5 +Author: Wolfgang Denk +Date: Tue Sep 9 10:06:44 2008 +0200 + + stxxtc: remove empty CONFIG_SHOW_ACTIVITY functions + + Signed-off-by: Wolfgang Denk + +commit 965de106ba8900372c8b16dc60d5acab7f925e38 +Author: Wolfgang Denk +Date: Tue Sep 9 10:03:47 2008 +0200 + + NETTA2: remove empty CONFIG_SHOW_ACTIVITY functions + + Signed-off-by: Wolfgang Denk + +commit 6cc64f9b5f69239c8b1969572b5a3a4aab7de5b9 +Author: Sergei Poselenov +Date: Fri Aug 15 15:42:11 2008 +0200 + + Removed hardcoded MxMR loop value from upmconfig() for MPC85xx. + + Signed-off-by: Sergei Poselenov + +commit 36241ca29d4804a1006fb3f26069effda5202581 +Author: Anatolij Gustschin +Date: Fri Aug 15 15:42:13 2008 +0200 + + 85xx: socrates: Enable Lime support. + + This patch adds Lime GDC support together with support for the PWM + backlight control through the w83782d chip. The reset pin of the + latter is attached to GPIO, so we need to reset it in + early_board_init_r. + + Signed-off-by: Anatolij Gustschin + +commit 7a47753ddcaebbf2142809842f70c5f723bd9ddb +Author: Detlev Zundel +Date: Fri Aug 15 15:42:12 2008 +0200 + + 85xx: Socrates: Major code update. + + - Update the local bus ranges in the FDT for Linux for the various + devices connected to the local bus via chip-select. + + - Set the LCRR_DBYP bit in the LCRR for local bus frequencies + lower than 66 MHz and uses I/O accessor functions consequently. + + - UPM data update. + + - Update of default environment and configuration. Use I2C multibus + as we do have two I2C buses. Also enable sdram and ext2 commands. + + Signed-off-by: Wolfgang Grandegger + Signed-off-by: Sergei Poselenov + Signed-off-by: Detlev Zundel + +commit 4d2ae70e8c31c22e5710df5ff236b5565ea2cf2c +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 9 01:22:39 2008 +0200 + + disk-on-chip: remove duplicate doc_probe declaration + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 3221b074a0ab199f6ae47c19cc22f42ddf3ef819 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 9 00:59:40 2008 +0200 + + onenand_uboot: fix warning: 'struct mtd_oob_ops' declared inside parameter list + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 13b4db0e2107175a8622ebb48529fa3ad8e12c75 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 9 00:59:39 2008 +0200 + + rs5c372: fix rtc_set prototype + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 1bb8b2ef2722bbaea3cc5d46321ce1d99f9b56f7 +Author: Sergei Poselenov +Date: Thu Aug 14 14:08:28 2008 +0200 + + ARM: fix warning: target CPU does not support interworking + + This patch fixes warnings like this: + + start.S:0: warning: target CPU does not support interworking + + which come from some ARM cross compilers and are caused by hard-coded + (with "--with-cpu=arm9" configuration option) ARM targets (which + support ARM Thumb instructions), while the ARM target selected from + the command line (with "-march=armv4") doesn't support Thumb + instructions. + + This warning is issued by the compiler regardless of the real use of + the Thumb instructions in code. + + To fix this problem, we use options according to compiler version + being used. + + Signed-off-by: Sergei Poselenov + Signed-off-by: Wolfgang Denk + +commit 4265c35fbcb248e58179007621d61d32d0b3b82a +Author: Sergei Poselenov +Date: Thu Aug 14 14:08:28 2008 +0200 + + ARM: Use do_div() instead of division for "long long". + + Signed-off-by: Sergei Poselenov + Signed-off-by: Wolfgang Denk + +commit 8febd13c69cb68652577d1a9fcbde954bf784155 +Author: Timur Tabi +Date: Fri Jul 18 16:52:23 2008 +0200 + + Update Freescale 85xx boards to sys_eeprom.c + + The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID + format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale + 86xx boards already use sys_eeprom.c, so this patch migrates the remaining + Freescale 85xx boards to use it as well. cds_eeprom.c is deleted. + + Signed-off-by: Timur Tabi + +commit 1055171ed05b7c4885737463d52b8d6c013bcb5d +Author: Wolfgang Denk +Date: Mon Sep 8 23:26:22 2008 +0200 + + lib_arm/bootm.c: fix compile warnings + + bootm.c:128: warning: label 'error' defined but not used + bootm.c:65: warning: unused variable 'ret' + + Signed-off-by: Wolfgang Denk + +commit 2e3c867d0a63c563a51e65b776973b008f16cec5 +Author: Wolfgang Denk +Date: Mon Sep 8 22:46:42 2008 +0200 + + ml507: fix out of tree build problem + + Signed-off-by: Wolfgang Denk + +commit 9863a15a98f23b79f34a0e4f9e465bc6df5d504d +Author: Wolfgang Denk +Date: Mon Sep 8 22:10:28 2008 +0200 + + common/cmd_bootm.c: fix printf() format warnings + + Signed-off-by: Wolfgang Denk + +commit 4394f9a8c42bb1b0abc4fc04bd582d4db5f8b726 +Author: Wolfgang Denk +Date: Mon Sep 8 22:37:45 2008 +0200 + + BMW, PCIPPC2, PCIPPC6, RBC82: fix compile warnings + + missing doc_probe() prototype. + + Signed-off-by: Wolfgang Denk + +commit 2c5e3cc4994897d364b148942ff23e47783198f6 +Author: Wolfgang Denk +Date: Mon Sep 8 21:28:14 2008 +0200 + + mk48t59: fix compile problem introduced by commit d1e23194 + + Signed-off-by: Wolfgang Denk + +commit 5ff889349d2ace13f10c9335e09365fcec8247cc +Author: Stefan Roese +Date: Mon Sep 8 14:11:12 2008 +0200 + + ppc4xx: Move ppc4xx specific prototypes to ppc4xx header + + This patch moves some 4xx specific prototypes out of include common.h + to a ppc4xx specific header. + + Signed-off-by: Stefan Roese + +commit ac53ee8318678190bf3c68da477a84a657d86fb0 +Author: Matthias Fuchs +Date: Fri Sep 5 15:34:04 2008 +0200 + + ppc4xx: Update CPCI405(AB) configuration + + This patch add FDT support and command line editing capabilities + for CPCI405 and CPCI405AB boards. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 7b1fbcadf73a83b3beb94abccda1c35e2c075a94 +Author: Matthias Fuchs +Date: Fri Sep 5 15:34:03 2008 +0200 + + ppc4xx: Cleanup CPCI405 linker script + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 767f9159c5c94cd0cb3135b5b82814ad12816ddf +Author: Matthias Fuchs +Date: Fri Sep 5 15:34:02 2008 +0200 + + ppc4xx: Update CPCI405 variants handling + + This patch replaces the BOARD_REVISION variable in include/config.mk + by a using a temporary include file in the platform directory. + + The former way does not work anymore and the latter is also used by + some other boards. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit f071f01fd09e9bf1cf09de37a7416aacce71bae1 +Author: Stefan Roese +Date: Mon Sep 8 10:01:48 2008 +0200 + + ppc4xx: Remove CONFIG_CS8952_PHY define + + Since this define is only used on one board that was never really in + production, removing this compile time option doesn't hurt and makes + the code more readable. + + Signed-off-by: Stefan Roese + +commit 6ca8646c1860bba74326bf916a5a3389a5c0d3b5 +Author: Stefan Roese +Date: Fri Sep 5 14:11:40 2008 +0200 + + ppc4xx: Fix compilation warning for PIP405 + + This patch fixes a compilation warning for the PIP405 board. It moves the + #ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't + occur anymore. I am a little unsure if this #ifdef is at the correct + place now or if it could be removed completely. This needs to get + tested on the PIP405 board. + + Signed-off-by: Stefan Roese + +commit 725b53ac61f4df3026b8f6489ef0080fd27d3816 +Author: Stefan Roese +Date: Fri Sep 5 14:09:09 2008 +0200 + + ppc4xx: Fix compilation warning for canyonlands & glacier + + Signed-off-by: Stefan Roese + +commit 302e52e0b1d4c7f994991709d0cb6c3ea612cdb5 +Author: Kumar Gala +Date: Fri Sep 5 14:40:29 2008 -0500 + + Fix compiler warning in mpc8xxx ddr code + + ctrl_regs.c: In function 'compute_fsl_memctl_config_regs': + ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function + ctrl_regs.c:523: note: 'caslat' was declared here + + Add a warning in DDR1 case if cas_latency isn't a value we know about. + + Signed-off-by: Kumar Gala + Acked-by: Jean-Christophe PLAGNIOL-VILLARD + +commit d1e2319414ea5218ba801163e4530ecf2dfcbf36 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Sep 1 23:06:23 2008 +0200 + + rtc: allow rtc_set to return an error and use it in cmd_date + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit ee9536a28cb149bcb6c5dee9d08c62c91f4c72d2 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Sep 1 01:16:33 2008 +0200 + + ap325rxa/favr-32-ezkit: Use CONFIG_FLASH_CFI_DRIVER + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 6b971c73f182248ce103503d74fbc0100bb8c8b7 +Author: Shinya Kuribayashi +Date: Sun Aug 31 05:37:04 2008 +0900 + + config.mk: Move arch-specific condition to $(ARCH)_config.mk + + Signed-off-by: Shinya Kuribayashi + +commit ea86b9e64b811753d9eabe0f560ee189fbe5d0c1 +Author: Kumar Gala +Date: Fri Aug 29 19:08:29 2008 -0500 + + Prevent crash if random/invalid ramdisks are passed to bootm + + Adds returning an error from the ramdisk detection code if + its not a real ramdisk (invalid). There is no reason we can't + just return back to the console if we detect an invalid + ramdisk or CRC error. + + Signed-off-by: Kumar Gala + +commit 8e02494e8f86c8f2d7324b5eb9e75271104a01ef +Author: Anatolij Gustschin +Date: Fri Aug 29 21:04:45 2008 +0200 + + Prevent crash if random DTB address is passed to bootm + + This patch adds bootm_start() return value check. If + error status is returned, we do not proceed further to + prevent board reset or crash as we still can recover + at this point. + + Signed-off-by: Anatolij Gustschin + +commit cc347801add2689b1ee54d21f62bc14ecf6e1dd8 +Author: Andrew Dyer +Date: Fri Aug 29 12:30:39 2008 -0500 + + clean up some #if !defined() in drivers/video/cfb_console.c + + rearrange some #if !defined() / #else / #endif statements to remove + the negative logic. + + Signed-off-by: Andrew Dyer + +commit c83f4c2d77f07174dcd6bef7e87a0f7017be7c33 +Author: Kyungmin Park +Date: Fri Aug 29 09:02:20 2008 +0900 + + apollon: use the last memory area for u-boot + + Signed-off-by: Kyungmin Park + +commit a6f2e455b774d0c5d56e44e5661df9adb69b6e07 +Author: Heiko Schocher +Date: Thu Aug 28 13:50:42 2008 +0200 + + TQM8272: move NAND part in seperate File + + I didn't try to use drivers/mtd/nand/fsl_upm.c for the NAND driver, + because I have no longer access to the hardware. + + Signed-off-by: Heiko Schocher + +commit 584f979f7ee914e32d408739cbdd2c4457ec18b8 +Author: Heiko Schocher +Date: Thu Aug 28 13:48:36 2008 +0200 + + TQM8272: Fix compiling error for the TQM8272 board. + + Fix compile problems caused by + commit cfa460adfdefcc30d104e1a9ee44994ee349bb7b + + Signed-off-by: Heiko Schocher + +commit 1a7f8ccec981648ccd38fca2535490582eee08e6 +Author: Kyungmin Park +Date: Wed Aug 27 14:45:20 2008 +0900 + + Add JFFS2 command support on OneNAND + + Signed-off-by: Kyungmin Park + +commit f5c3ba79788b0e39baab7026d374fe375dd1a43f +Author: Mark Jackson +Date: Mon Aug 25 19:21:30 2008 +0100 + + Allow console input to be disabled + + Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE. + + When CONFIG_DISABLE_CONSOLE is defined, setting + GD_FLG_DISABLE_CONSOLE disables all console input and output. + + Signed-off-by: Mark Jackson + +commit 2b22d608f370565c87f55928b524207031419c11 +Author: Ricardo Ribalda Delgado +Date: Wed Jul 30 12:39:29 2008 +0200 + + loads: allow negative offsets + + Signed-off-by: Ricardo Ribalda Delgado + +commit e90fb6afab2c0c074dfb67bacb4de179eb188a24 +Author: Yuri Tikhonov +Date: Thu Sep 4 11:19:05 2008 +0200 + + USB EHCI: reset root hub + + Some of multi-function USB controllers (e.g. ISP1562) allow root hub + resetting only via EHCI registers. So, this patch adds the + corresponding kind of reset to OHCI's hc_reset() if the newly + introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates + board). + + Signed-off-by: Yuri Tikhonov + Acked-by: Markus Klotzbuecher + +commit 5875d358f025c1b042d8a0f08384b756de7256c9 +Author: Yuri Tikhonov +Date: Fri Aug 15 15:42:09 2008 +0200 + + RX 8025 RTC: analyze 12/24-hour mode flag in rtc_get(). + + Signed-off-by: Yuri Tikhonov + +commit 3e3c026ed746a284c6f0ef139b26d859939de7e9 +Author: Stefan Roese +Date: Fri Sep 5 10:47:46 2008 +0200 + + devices: Use list_add_tail() instead of list_add() to register a device + + This patch fixes a problem spotted on Glacier/Canyonlands (and most + likely lots of other board ports), that no serial output was seen + after console initialization in console_init_r(). This is because the + last added console device was used instead of the first added. + + This patch fixes this problem by using list_add_tail() instead of + list_add() to register a device. This way the first added console + is used again. + + Signed-off-by: Stefan Roese + +commit 78d78236896d62bb8ca7302af38d8f1493eb2651 +Author: Victor Gallardo +Date: Thu Sep 4 23:49:36 2008 -0700 + + ppc4xx: Add support for GPCS, SGMII and M88E1112 PHY + + This patch adds GPCS, SGMII and M88E1112 PHY support + for the AMCC PPC460GT/EX processors. + + Signed-off-by: Victor Gallardo + Signed-off-by: Stefan Roese + +commit f6b6c45840f9b4671d2d97243a12a1f3ffb64765 +Author: Adam Graham +Date: Wed Sep 3 12:26:59 2008 -0700 + + ppc4xx: Update Kilauea to use PPC4xx DDR autocalibration routines + + Signed-off-by: Adam Graham + Signed-off-by: Stefan Roese + +commit 075d0b81e896e8735ae26372cd384f87cbd24e41 +Author: Adam Graham +Date: Wed Sep 3 12:26:28 2008 -0700 + + ppc4xx: IBM Memory Controller DDR autocalibration routines + + Alternate SDRAM DDR autocalibration routine that can be generically used + for any PPC4xx chips that have the IBM SDRAM Controller core allowing for + support of more DIMM/memory chip vendors and gets the DDR autocalibration + values which give the best read latency performance (SDRAM0_RDCC.[RDSS]). + + Two alternate SDRAM DDR autocalibration algoritm are provided in this patch, + "Method_A" and "Method_B". DDR autocalibration Method_A scans the full range + of possible PPC4xx SDRAM Controller DDR autocalibration values and takes a + lot longer to run than Method_B. Method_B executes in the same amount of time + as the currently existing DDR autocalibration routine, i.e. 1 second or so. + Normally Method_B is used and it is set as the default method. + + The current U-Boot PPC4xx DDR autocalibration code calibrates the IBM SDRAM + Controller registers.[bit-field]: + 1) SDRAM0_RQDC.[RQFD] + 2) SDRAM0_RFDC.[RFFD] + + This alternate PPC4xx DDR autocalibration code calibrates the following + IBM SDRAM Controller registers.[bit-field]: + + 1) SDRAM0_WRDTR.[WDTR] + 2) SDRAM0_CLKTR.[CKTR] + 3) SDRAM0_RQDC.[RQFD] + 4) SDRAM0_RFDC.[RFFD] + + and will also use the calibrated settings of the above four registers that + produce the best "Read Sample Cycle Select" value in the SDRAM0_RDCC.[RDSS] + register.[bit-field]. + + Signed-off-by: Adam Graham + Signed-off-by: Stefan Roese + +commit e07f4a8033b6270b8103049adb6456f660ff4a89 +Author: Ricardo Ribalda Delgado +Date: Mon Sep 1 13:09:39 2008 -0400 + + ppc44x: Unification of virtex5 pp440 boards + + This patch provides an unificated way of handling xilinx v5 ppc440 boards. + + It unificates 3 different things: + + 1) Source code + A new board called ppc440-generic has been created. This board includes + a generic tlb initialization (Maps the whole memory into virtual) and + defines board_pre_init, checkboard, initdram and get_sys_info weakly, + so, they can be replaced by specific functions. + + If a new board needs to redefine any of the previous functions + (specific initialization) it can create a new directory with the + specific initializations needed. (see the example ml507 board). + + 2) Configuration file + Common configurations are located under configs/xilinx-ppc440.h, this + header file interpretes the xparameters file generated by EDK and + configurates u-boot in correspondence. Example: if there is a Temac, + allows CMD_CONFIG_NET + Specific configuration are located under specific configuration file. + (see the example ml507 board) + + 3) Makefile + Some work has been done in order to not duplicate work in the Main + Makefile. Please see the attached code. + + In order to support new boards they can be implemented in the next way: + + a) Simple Generic Board (90% of the time) + Using EDK generates a new xparameters.h file, replace + ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config + && make + + b) Simple Boards with special u-boot parameters (9 % of the time) + Create a new file under configs for it (use ml507.h as example) and + change your paramaters. Create a new Makefile paragraph and compile + + c) Complex boards (1% of the time) + Create a new folder for the board, like the ml507 + + Finally, it adds support for the Avnet FX30T Evaluation board, following + the new generic structure: + + Cheap board by Avnet for evaluating the Virtex5 FX technology. + + This patch adds support for: + - UartLite + - 16MB Flash + - 64MB RAM + + Prior using U-boot in this board, read carefully the ERRATA by Avnet + to solve some memory initialization issues. + + Signed-off-by: Ricardo Ribalda Delgado + Signed-off-by: Stefan Roese + +commit 64ac1eb5afafced49b327425ad1814b2dc422d6e +Author: Nick Spence +Date: Tue Sep 2 15:21:16 2008 -0500 + + mpc83xx: fix mpc8313 in-tree building with NAND + + and add mpc8313 NAND build to MAKEALL + + Signed-off-by: Nick Spence + Signed-off-by: Kim Phillips + +commit 6eb2a44e27919fdc601e0c05404b298a7602c0e3 +Author: Nick Spence +Date: Thu Aug 28 14:09:25 2008 -0700 + + mpc83xx: clean up cache operations and unlock_ram_in_cache() functions + + Cleans up some latent issues with the data cache control so that + dcache_enable() and dcache_disable() will work reliably (after + unlock_ram_in_cache() has been called) + + Signed-off-by: Nick Spence + Signed-off-by: Kim Phillips + +commit 46497056ae3b1e81e736e9cf3a170472c5d9719f +Author: Nick Spence +Date: Thu Aug 28 14:09:19 2008 -0700 + + mpc83xx: Store and display Arbiter Event Register values + + Record the Arbiter Event Register values and optionally display them. + + The Arbiter Event Register can record the type and effective address of + an arbiter error, even through an HRESET. This patch stores the values in + the global data structure. + + Display of the Arbiter Event registers immediately after the RSR value + can be enabled with defines. The Arbiter values will only be displayed + if an arbiter event has occured since the last Power On Reset, and either + of the following defines exist: + #define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and + and type register values + #define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter + event register values + + Address Only transactions are one of the trapped events that can register + as an arbiter event. They occur with some cache manipulation instructions + if the HID0_ABE (Address Broadcast Enable) is set and the memory region + has the MEMORY_COHERENCE WIMG bit set. Setting: + #define CONFIG_MASK_AER_AO - prevents the arbiter from recording address + only events, so that it can still capture + other real problems. + + Signed-off-by: Nick Spence + Signed-off-by: Kim Phillips + +commit ade50c7fa1b16ef98be17e9c3ae286aecf4f5605 +Author: Nick Spence +Date: Thu Aug 28 14:09:11 2008 -0700 + + mpc83xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache + + This is needed in unlock_ram_in_cache() because it is called from C and + will corrupt the small data area anchor that is kept in R2. + + lock_ram_in_cache() is modified similarly as good coding practice, but + is not called from C. + + Signed-off-by: Nick Spence + Signed-off-by: Kim Phillips + +commit d9fe88173cb4f7d293796ffe10c7a0d3d426d8f9 +Author: Nick Spence +Date: Fri Aug 22 23:52:50 2008 -0700 + + MPC83XX: Fix GPIO configuration - set gpio level before direction + + Set DAT value before DIR values to avoid creating glitches on the + GPIO signals. + + Set gpio level register before direction register to inhibit + glitches on high level output pins. + + Dir and data gets cleared at powerup, so high level output lines see + a short low pulse between setting the direction and level registers. + + Issue was seen on a new board with the nReset line of the NOR flash + connected to a GPIO. Setting the direction register puts the NOR flash + in reset so the next instruction to set the level cannot get executed. + + Signed-off-by: Nick Spence + Signed-off-by: Peter Korsgaard + Signed-off-by: Kim Phillips + +commit 7007c5975ee900ad70983b0681d3251e221f8321 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Sep 2 02:58:32 2008 +0200 + + doc/qemu_mips: add doc howto debug u-boot with gdb + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 7deb3b3ecd0e81ef09bb68aa0ec2346f4ae0a405 +Author: Matthias Fuchs +Date: Wed Sep 3 17:15:45 2008 +0200 + + ppx4xx: Fix broken DASA_SIM board + + This patch adds initdram() to DASA_SIM boards that has been + removed accidentally by a previous commit. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 7e410aa30fbcb1d19a26bbf1e84a9ca6102d534b +Author: Stefan Roese +Date: Mon Sep 1 08:35:37 2008 +0200 + + ppc4xx: Remove reference to common/lists.o from some esd linker scripts + + This patch removes some direct references to common/lists.o from some + esd linker scripts. This is necessary because the lists source was moved + and is not in the "common" directory anymore. + + Signed-off-by: Stefan Roese + +commit 97b0734d65f8a0b03df0a335a2addc759da56107 +Author: Matthias Fuchs +Date: Tue Sep 2 16:33:05 2008 +0200 + + ppc4xx: Remove obsolete or unused functions from some esd boards + + This patch removes initdram() and testdram() from most esd 405 platforms. + Some boards also have an empty dummy implementation of + misc_init_f(). This is also removed. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 1092ce218c514e5ccb18450ac5af501d96d6e3e9 +Author: Matthias Fuchs +Date: Tue Sep 2 15:07:54 2008 +0200 + + ppc4xx: Update VOM405 board configuration + + - remove PCI code + - add command line editing + - minor cleanup + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 830c800e28e96ec7c3c6936a0bd1b9461f3e77d4 +Author: Matthias Fuchs +Date: Tue Sep 2 15:07:53 2008 +0200 + + ppc4xx: Remove obsolete initdram() function from VOM405 board + + This patch removed the obsolete initdram() function from + VOM405 platform file. + + Some minor cleanup. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 3d4dd7a941b2327b8c2fc535b782ca307ff8b6c8 +Author: Matthias Fuchs +Date: Tue Sep 2 15:07:52 2008 +0200 + + ppc4xx: Cleanup VOM405 linker script + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit fcaffd597f6f5191b12ca66c2a4789bbdeea85c2 +Author: Matthias Fuchs +Date: Tue Sep 2 15:07:51 2008 +0200 + + ppc4xx: Add fdt support for VOM405 boards + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 9ec367aa2c5dcf79558aa2b209b45d7686654c14 +Author: Matthias Fuchs +Date: Tue Sep 2 11:36:14 2008 +0200 + + ppc4xx: Coding style cleanup + + Wrap long lines etc. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 17e65c21adfb63980e6aff80bfbd2df0eeb12060 +Author: Matthias Fuchs +Date: Tue Sep 2 11:35:56 2008 +0200 + + ppc4xx: Enable USB on PLU405 boards + + This patch enables the PCI-OHCI controller on PLU405 board. + + Also the default CPU frequency is updated to 266 MHz and + command line editing is enabled. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 40e43e3b87d57b2ac786e27f6e25a7df9940d93b +Author: Matthias Fuchs +Date: Tue Sep 2 11:35:35 2008 +0200 + + ppc4xx: Cleanup PLU405 platform file + + This patch + - wraps some long lines + - removes unused/obsolete functions: misc_init_f() and initdram() + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit d74cdb1d0614ab78128e0735a51e7988a7b7ea33 +Author: Matthias Fuchs +Date: Tue Sep 2 11:35:04 2008 +0200 + + ppc4xx: Cleanup PLU405 linker script + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 3bc1054cec2f6b25822f301ea922a16233baa4c7 +Author: Matthias Fuchs +Date: Tue Sep 2 11:34:36 2008 +0200 + + ppc4xx: Add fdt support for PLU405 boards + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 5a3e480b783bfbc139586293a54fb875d7c5c5d4 +Author: Matthias Fuchs +Date: Tue Sep 2 11:34:08 2008 +0200 + + ppc4xx: Increase U-Boot size to 384kB for PLU405 boards + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit be1b0d2777e179191a57b138b660547a17e55aad +Author: Jochen Friedrich +Date: Tue Sep 2 11:24:59 2008 +0200 + + Don't tftp to unknown flash + + If a board has a variable number of flash banks, there are empty entries + in flash_info[] and CFG_DIRECT_FLASH_TFTP is set, tftp boot fails with + "Outside available Flash". This patch skips flash banks with unknown + flash ids. + + Signed-off-by: Jochen Friedrich + Signed-off-by: Ben Warren + +commit 33314470ab32a3f5412bb61b5f3d6c216c88bf9b +Author: Nobuhiro Iwamatsu +Date: Thu Aug 28 13:40:44 2008 +0900 + + net: smc911x: Add pkt_data_pull and pkt_data_push function + + The RSK7203 board has the SMSC9118 wired up 'incorrectly'. + Byte-swapping is necessary, and so poor performance is inevitable. + This problem cannot evade by the swap function of CHIP, this can + evade by software Byte-swapping. + And this has problem by FIFO access only. pkt_data_pull/pkt_data_push + functions necessary to solve this problem. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Ben Warren + +commit 10efa024b8ffd9e6aaca63da8bddfdffdc672274 +Author: Ben Warren +Date: Sun Aug 31 20:37:00 2008 -0700 + + Moved initialization of EEPRO100 Ethernet controller to board_eth_init() + + Affected boards: + db64360 + db64460 + katmai + taihu + taishan + yucca + cpc45 + cpu87 + eXalion + elppc + debris + kvme080 + mpc8315erdb + integratorap + ixdp425 + oxc + pm826 + pm828 + pm854 + pm856 + ppmc7xx + sc3 + sc520_spunk + sorcery + tqm8272 + tqm85xx + utx8245 + + Removed initialization of the driver from net/eth.c + Also, wrapped contents of pci_eth_init() by CONFIG_PCI. + + Signed-off-by: Ben Warren + +commit 8ca0b3f99c4fce7a599dcaf92ae095496dc8c8e0 +Author: Ben Warren +Date: Sun Aug 31 10:45:44 2008 -0700 + + Moved initialization of TULIP Ethernet controller to board_eth_init() + + Affected boards: + cu824 + bab7xx + adciop + dasa_sim + mousse + mpc8540eval + musenki + mvblue + pcippc2/pcippc6 + sbc8240 + stxssa + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit ad3381cf4167120db5c7b88e4970245e1d5c0a32 +Author: Ben Warren +Date: Sun Aug 31 10:44:19 2008 -0700 + + Moved initialization of E1000 Ethernet controller to board_eth_init() + + Affected boards: + ap1000 + mvbc_p + PM854 + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 4fce2aceaf8afd31a252bc782c9dbc497bf40487 +Author: Ben Warren +Date: Sun Aug 31 10:40:51 2008 -0700 + + Moved initialization of plb2800 Ethernet driver to board_eth_init + + Affected boards: + purple + + Removed initialization of controller from net/eth.c + + Signed-off-by: Ben Warren + +commit e1d7480b5de1fd4830bf7cf5e2237d3b0846d08d +Author: Ben Warren +Date: Sun Aug 31 10:39:12 2008 -0700 + + Moved initialization of MPC5xxx_FEC Ethernet driver to CPU directory + + Modified board_eth_init() functions of boards that have this FEC in addition + to other Ethernet controllers. + + Affected boards: + bc3450 + icecube + mvbc_p + o2dnt + pm520 + total5200 + tq5200 + + Removed initialization of controller from net/eth.c + + Signed-off-by: Ben Warren + +commit a0aad08f9427ac00218bdb2cb649833ce6ec9b8d +Author: Ben Warren +Date: Sun Aug 31 10:36:38 2008 -0700 + + Moved initialization of MPC512x_FEC Ethernet driver to CPU directory + + Added a cpu_eth_init() function to MPC512x CPU directory and + removed code from net/eth.c + + Signed-off-by: Ben Warren + +commit 8218bd2aa68820b878a8413493ae17fd8d21f944 +Author: Ben Warren +Date: Sun Aug 31 10:16:59 2008 -0700 + + Moved initialization of IncaIP Ethernet controller to board_eth_init + + Affected boards: + IncaIP + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 164846eeb25cb2a5ede7ab9371fdca7f4831a055 +Author: Ben Warren +Date: Sun Aug 31 10:15:26 2008 -0700 + + Moved initialization of 3COM Ethernet controller (AmigaOne) to board_eth_init() + + Affected boards: + AmigaOneG3SE + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 6aca145e067efe75398e9fac97822bd3700de0b2 +Author: Ben Warren +Date: Sun Aug 31 10:13:34 2008 -0700 + + Moved initialization of GT6426x Ethernet controller to board_eth_init() + + Affected boards: + EVB64260 + P3G4 + ZUMA + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit e3090534d62045dcb73f5392bacc64a4e8e443dc +Author: Ben Warren +Date: Sun Aug 31 10:08:43 2008 -0700 + + Moved initialization of PCNET Ethernet controller to board_eth_init() + + Affected boards: + PN62 + sc520_cdp + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit b902b8dda5e1fd4d5fe2f202c71ee3521d2c40ed +Author: Ben Warren +Date: Sun Aug 31 10:07:16 2008 -0700 + + Moved initialization of NATSEMI Ethernet controller to board_eth_init() + + Affected boards: + a3000 + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 19403633dd70333893c2da7926a1d0dcd6dab7d8 +Author: Ben Warren +Date: Sun Aug 31 10:03:22 2008 -0700 + + Moved initialization of NS8382X Ethernet controller to board_eth_init() + + Affected boards: + bc3450 + cpci5200 + mecp5200 + pf2000 + icecube + o2dnt + pm520 + sandpoint8245 + total5200 + tqm5200 + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit ccdd12f83ef93719fbe85f642aa4dc648b9498f0 +Author: Ben Warren +Date: Sun Aug 31 09:59:33 2008 -0700 + + Moved initialization of TSI108 Ethernet controller to board_eth_init() + + Affected boards: + mpc7448hpc2 + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 0b252f50ae218ae15bfb63af44227972686ebc56 +Author: Ben Warren +Date: Sun Aug 31 21:41:08 2008 -0700 + + Moved initialization of RTL8139 Ethernet controller to board_eth_init() + + Affected boards: + hidden_dragon + MPC8544DS + MPC8610HPCN + R2DPLUS + TB0229 + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 02d69891d95ee76b0e86e1715a4dc0b964a57cb7 +Author: Ben Warren +Date: Sun Aug 31 09:49:42 2008 -0700 + + Moved initialization of RTL8169 Ethernet controller to board_eth_init() + + Affected boards: + linkstation + r7780mp + + Removed initialization of the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 3ae071e44256144d6c1e3febb65f6c56bd433769 +Author: Ben Warren +Date: Tue Aug 12 22:11:53 2008 -0700 + + Moved initialization of Ethernet controllers on Atmel AT91 to board_eth_init() + + Removed at91sam9_eth_initialize() from net/eth.c + + Signed-off-by: Ben Warren + +commit 89973f8a82c28ad893c4c3cc56839a8e10fe5f13 +Author: Ben Warren +Date: Sun Aug 31 22:22:04 2008 -0700 + + Introduce netdev.h header file and remove externs + + This addresses all drivers whose initializers have already + been moved to board_eth_init()/cpu_eth_init(). + + Signed-off-by: Ben Warren + +commit 5a8a163ac394d9f4f7ff57f415d82bd673b0068c +Author: Andy Fleming +Date: Sun Aug 31 16:33:30 2008 -0500 + + Add pixis_set_sgmii command + + The 8544DS and 8572DS platforms support an optional SGMII riser card to + expose ethernet over an SGMII interface. Once the card is in, it is also + necessary to configure the board such that it uses the card, rather than + the on-board ethernet ports. This can either be done by flipping dip switches + on the motherboard, or by modifying registers in the pixis. Either way + requires a reboot. + + This adds a command to allow users to choose which ports are routed through + the SGMII card, and which through the onboard ports. It also allows users + to revert to the current switch settings. + + This code does not work on the 8572, as the PIXIS is different. + + Signed-off-by: Andy Fleming + Signed-off-by: Ben Warren + +commit 216f2a7156a5fde7b47adc40ad553c888a9cbaa7 +Author: Andy Fleming +Date: Sun Aug 31 16:33:29 2008 -0500 + + Add SGMII support for the 8544 DS + + The 8544 DS has an optional SGMII Riser card, which uses different PHY + addresses. Check if we are in SGMII mode, and invoke the SGMII Riser + setup code if so. + + Signed-off-by: Andy Fleming + Signed-off-by: Ben Warren + +commit 652f7c2eef76a1340928bd660845441e932d86a2 +Author: Andy Fleming +Date: Sun Aug 31 16:33:28 2008 -0500 + + Add support for Freescale SGMII Riser Card + + The 8544DS and 8572DS systems have an optional SGMII riser card which + exposes new ethernet ports which are connected to the eTSECs via an + SGMII interface. The SGMII PHYs for this board are offset from the standard + PHY addresses, so this code modifies the passed in tsec_info structure to + use the SGMII PHYs on the card, instead. + + Signed-off-by: Andy Fleming + Signed-off-by: Ben Warren + +commit 2abe361c03b43e6dcf68f54e96b5c05156c49284 +Author: Andy Fleming +Date: Sun Aug 31 16:33:27 2008 -0500 + + Add SGMII support to the tsec + + Adds support for configuring the TBI to talk properly with the SerDes. + + Signed-off-by: Andy Fleming + Signed-off-by: Ben Warren + +commit 75b9d4ae0d69f214eab641caf12ce8af83a39a42 +Author: Andy Fleming +Date: Sun Aug 31 16:33:26 2008 -0500 + + Pass in tsec_info struct through tsec_initialize + + The tsec driver contains a hard-coded array of configuration information + for the tsec ethernet controllers. We create a default function that works + for most tsecs, and allow that to be overridden by board code. It creates + an array of tsec_info structures, which are then parsed by the corresponding + driver instance to determine configuration. Also, add regs, miiregs, and + devname fields to the tsec_info structure, so that we don't need the kludgy + "index" parameter. + + Signed-off-by: Andy Fleming + Signed-off-by: Ben Warren + +commit dd3d1f56a01f460d560766126ee7dfed2ea9bc10 +Author: Andy Fleming +Date: Sun Aug 31 16:33:25 2008 -0500 + + tsec: Move tsec.h to include/ + + This is to prepare the way for board code passing in the tsec_info structure + + Signed-off-by: Andy Fleming + Signed-off-by: Ben Warren + +commit d23dc394aa69093b6326ad917db04dc0d1aff3f8 +Author: Sergei Poselenov +Date: Fri Jun 6 15:52:44 2008 +0200 + + PHY: Add support for the M88E1121R Marvell chip. + + Signed-off-by: Yuri Tikhonov + Signed-off-by: Sergei Poselenov + Signed-off-by: Ben Warren + +commit 1711f3bd16d1c5e9d17b4c0198b426d86999781b +Author: Wolfgang Denk +Date: Tue Sep 2 21:17:36 2008 +0200 + + fw_env.c: fix build problems with MTD_VERSION=old + + (as needed to support old 2.4 Linux kernel based releases) + + Signed-off-by: Wolfgang Denk + +commit 628ffd73bcff0c9f3bc5a8eeb2c7455fe9d28a51 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Sep 1 17:11:26 2008 +0200 + + device: make device_register() clone the device + + This is expected by the callers, but this fact was hidden well within + the old list implementation. + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit c75e772a2f061a508bba28ded1b5bea91f0442b0 +Author: Nobuhiro Iwamatsu +Date: Sun Aug 31 23:28:15 2008 +0900 + + sh: Remove CC line from board's Makefile + + Signed-off-by: Nobuhiro Iwamatsu + +commit 468eae0660de6fdfd9999944c536ecc4797bd944 +Author: Nobuhiro Iwamatsu +Date: Sun Aug 31 23:25:57 2008 +0900 + + sh: Replaced "@./mkconfig" for @$(MKCONFIG) + + Signed-off-by: Nobuhiro Iwamatsu + +commit 3aeb1ff7482a732503186c742d3a5ded4b7a0d34 +Author: Nobuhiro Iwamatsu +Date: Thu Aug 28 14:50:52 2008 +0900 + + sh: Add support sh2 to MAKEALL + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 6f3d8bb5faa12dbf3031382286784c978df038ee +Author: Nobuhiro Iwamatsu +Date: Thu Aug 28 14:52:23 2008 +0900 + + sh: Fix compile error rsk7203 board + + This boards used old type preprocessor. + This patch fix compile error. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 1c98172e025018552e9bb4c43b0aaee76f79b1aa +Author: Nobuhiro Iwamatsu +Date: Thu Aug 28 14:53:31 2008 +0900 + + sh: Fix compile error sh7785lcr board + + This boards used old type preprocessor. + This patch fix compile error. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 6f0da4972e48f99d37bc522814940a6022cd3084 +Author: Nobuhiro Iwamatsu +Date: Fri Aug 22 17:39:09 2008 +0900 + + sh: Renesas Solutions AP325RXA board support + + AP325RXA is SH7723's reference board. + This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other. + In this patch, support SCIF, NOR Flash, and Ethernet. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit ab09f433b50bb83b5e440c335bc3839ee069e534 +Author: Nobuhiro Iwamatsu +Date: Fri Aug 22 17:48:51 2008 +0900 + + sh: add support Renesas SH7723 + + Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other. + This patch supports CPU register's header file and SCIF serial driver. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit c655fad06ba3fb042dbc667724a40e1a9a091248 +Author: Nobuhiro Iwamatsu +Date: Sun Aug 31 23:02:04 2008 +0900 + + sh: Renesas RSK+ 7203 board support + + This adds initial support for the RTE RSK+ SH7203 board. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 6ede753ddf52a7b0f992d9bccbe5e4a0968ca475 +Author: Nobuhiro Iwamatsu +Date: Thu Jul 3 23:11:02 2008 +0900 + + sh: Add support Renesas SH7203 processor + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 6ad43d0dd86b612895ddc7f480eb6cdfe793adf9 +Author: Nobuhiro Iwamatsu +Date: Sun Aug 31 22:48:33 2008 +0900 + + sh: Add support SH2/SH2A which is CPU of Renesas Technology + + Add support SH2/SH2A basic function. + + Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Nobuhiro Iwamatsu + +commit 0d53a47dc0737b6aa3a39caee21410c169441ae5 +Author: Nobuhiro Iwamatsu +Date: Sun Aug 31 22:45:08 2008 +0900 + + sh: Renesas R0P7785LC0011RL board support + + This board has SH7785, 512MB DDR2-SDRAM, NOR Flash, + Graphic, Ethernet, USB, SD, RTC, and I2C controller. + + This patch supports the following functions: + - 128MB DDR2-SDRAM (29-bit address mode only) + - NOR Flash + - USB host + - Ethernet + + Signed-off-by: Yoshihiro Shimoda + Signed-off-by: Nobuhiro Iwamatsu + +commit b0b6218929bc7de9a6bdb8e564fa8ec2efa71b4e +Author: Yoshihiro Shimoda +Date: Thu Jul 10 19:32:53 2008 +0900 + + sh: add support for SH7785 + + Renesas SH7785 has DDR2-SDRAM controller, PCI, and other. + This patch supports CPU register's header file. + + Signed-off-by: Yoshihiro Shimoda + Signed-off-by: Nobuhiro Iwamatsu + +commit d6e04258be8f2408845468d3cf722a4cf0433445 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Aug 31 04:45:42 2008 +0200 + + davinci: fix remaining dm644x_eth + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 08ab4e1780fa63c88dd5a5ab52f4ff4ed1ee1878 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Aug 31 04:24:56 2008 +0200 + + fs: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit c1de7a6daf9c657484e1c6d433f01fccd49a7f48 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Aug 31 04:24:55 2008 +0200 + + devices: merge to list_head + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit ef0255fc75f28655f9681422079287d68a14dbaa +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Aug 31 04:24:51 2008 +0200 + + update linux/list + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 71cb31227bee741b274f6c0279b2aac1ab8e28e3 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Aug 31 00:39:48 2008 +0200 + + smdk6400: add gitignore + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit f9f692e2b146d4e306b777e6d5f69f1d725b9eb9 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Aug 31 00:39:48 2008 +0200 + + smdk6400: Use CONFIG_FLASH_CFI_DRIVER + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 7c0e5a8db3d1358b0ce3cc85ada0de6341ca4a15 +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:47 2008 +0200 + + smdk6400: remove redundant bootargs definition + + Double bootargs setting leads to a duplicated environmant entry. + + Signed-off-by: Guennadi Liakhovetski + +commit 11edcfe260f20dcea79284a3e95270989d433854 +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:47 2008 +0200 + + ARM: Add support for S3C6400 based SMDK6400 board + + SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl + driver for it too. The board can also boot from the NOR flash, but due to + hardware limitations it can only address 64KiB on it, which is not enough + for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6. + + Signed-off-by: Guennadi Liakhovetski + +commit e0056b341069796eaea11eae0fc8eb93a3dceaac +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:47 2008 +0200 + + NAND: add NAND driver for S3C64XX + + Based on the original S3C64XX NAND driver by Samsung for U-Boot 1.1.6. + + Signed-off-by: Guennadi Liakhovetski + +commit 3fe7b589f9c7463df39056f8872006a67f56a91c +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:47 2008 +0200 + + S3C64XX: remove broken HWFLOW support from the serial driver + + As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is + broken and currently unused. Remove it. + + Signed-off-by: Guennadi Liakhovetski + +commit 2fb28dcf82048045e1bf5014e938e486fa6c2383 +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:47 2008 +0200 + + serial: add S3C64XX serial driver + + Based on the original S3C64XX UART driver by Samsung for U-Boot 1.1.6. + + Signed-off-by: Guennadi Liakhovetski + +commit 8262813ca04fc57f5d8856e1828085c136e0f1eb +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:46 2008 +0200 + + USB: Add support for OHCI controller on S3C6400 + + Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could + try to enable the MMU, but map addresses 1-to-1, and disable data cache, then + it should work too and we could still profit from instruction cache. + + Signed-off-by: Guennadi Liakhovetski + +commit 9b07773f8883665b002500c190507e9fd99b7181 +Author: Guennadi Liakhovetski +Date: Sun Aug 31 00:39:46 2008 +0200 + + ARM: Add arm1176 core with S3C6400 SoC + + Based on the original S3C64XX port by Samsung for U-Boot 1.1.6. + + Signed-off-by: Guennadi Liakhovetski + +commit fcaac589a68115819ddadcf5c18ded9a5f9e2c75 +Author: Sandeep Paulraj +Date: Sun Aug 31 00:39:46 2008 +0200 + + ARM DaVinci: Changing function names for EMAC driver + + DM644x is just one of a series of DaVinci chips that use the EMAC driver. + By replacing all the function names that start with dm644x_* to davinci_* + we make these function more portable. I have tested this change on my EVM. + DM6467 is another DaVinci SOC which uses the EMAC driver and i will + be sending patches that add DaVinci DM6467 support to the list soon. + + Signed-off-by: Sandeep Paulraj + +commit fbbb1de369ca7d5ace6f7b0ce9d0aee24a6f457b +Author: Gururaja Hebbar K R +Date: Sat Aug 30 23:21:30 2008 +0200 + + Integrator[AP/CP] - Remove unused file memsetup.S + + - memsetup.s is changed/merged to lowlevel_init.S + memsetup.S has a global label memsetup that just returns back to caller + - memsetup global label is changed/merged to lowlevel_init + This label is not called from anywhere. + + Signed-off-by: Gururaja Hebbar + +commit 89d51d022a63be1a851eda983c8cbce1a044f65f +Author: Hugo Villeneuve +Date: Wed Aug 27 21:35:52 2008 +0200 + + ARM DaVinci: Standardize names of directories/files + + ARM DaVinci: Standardize names of directories/files. + + Signed-off-by: Hugo Villeneuve + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 264bbdd11d01f14f5ea4629556ae63b00b13402d +Author: Hugo Villeneuve +Date: Fri Jul 11 15:10:13 2008 -0400 + + ARM DaVinci: Move common functions to board/davinci/common + + ARM DaVinci: Move common functions to board/davinci/common. + + Signed-off-by: Hugo Villeneuve + +commit c2b4b2e4814f4ace9015fdb64132894327400bf0 +Author: Stefan Roese +Date: Fri Aug 29 11:56:49 2008 +0200 + + ppc4xx/NAND: Add select_chip function to 4xx NDFC driver + + This function is needed for the new NAND infrastructure. We only need + a dummy implementation though for the NDFC. + + Signed-off-by: Stefan Roese + +commit 3d4a746e2fb4545f07d871049805fb34ae97cc94 +Author: Stefan Roese +Date: Fri Aug 29 12:06:27 2008 +0200 + + ppc4xx: Increase image size for NAND boot target + + This is needed since now with HUSH enabled (amcc-common.h) the image + read from NAND exceeds the previous limit. + + Signed-off-by: Stefan Roese + +commit 6b5049d056cd8ef72d1f2f461ceb2d033d93f759 +Author: Ben Warren +Date: Thu Aug 28 23:58:30 2008 -0700 + + Move MPC512x_FEC driver to drivers/net + + Signed-off-by: Ben Warren + +commit 80b00af01b3c9154774de2936f05a051e92f6a03 +Author: Ben Warren +Date: Thu Aug 28 23:58:29 2008 -0700 + + Move MPC5xxx_FEC driver to drivers/net + + Signed-off-by: Ben Warren + +commit 3de7bf0e6b1ad2608014096c8192f13229b2e9d7 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Aug 29 21:53:57 2008 +0200 + + cmd_terminal: remove no need ifdef + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 578118bdf122877ae769776be002255be447b4fa +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Aug 29 21:53:57 2008 +0200 + + common/Makefile: order by functionality + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit ba7b5b2348b684cf8ec424b2e38e267dc1cfd2fb +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Aug 29 21:53:56 2008 +0200 + + miiphyutil: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 81789c39db3f0f6b621df8c0ec66014d701f368e +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Aug 29 21:53:37 2008 +0200 + + autoscript: Move conditional compilation to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit bbf52df9aa94ffb115b8b1ebeb00d01374bb0a1d +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Aug 29 01:18:11 2008 +0200 + + crc16: move to lib_generic + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 55195773eacefb22dd483a3c560ea30a14263ce1 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Fri Aug 29 01:18:01 2008 +0200 + + miiphybb: move to drivers/net/phy + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit e8314035996a9118ac5948df2ff8a2f2161ed67a +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Thu Aug 28 12:31:51 2008 +0200 + + soft_spi: move to drivers/spi + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 4d75e0aa9caca64d4a1d55d95cd1ca5f30d9fc56 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Thu Aug 28 12:31:51 2008 +0200 + + soft_i2c: move to drivers/i2c + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 717a222229fdb77703e9174d0eb08a4b41febf49 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Thu Aug 28 12:31:48 2008 +0200 + + gunzip: move to lib_generic + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 52aef8f9ba28b747973bf76741c23db658d5773c +Author: Wolfgang Ocker +Date: Tue Aug 26 19:55:23 2008 +0200 + + ppc4xx: NAND configuration + + Made NAND bank configuration setting a config variable. + + Signed-off-by: Wolfgang Ocker + Signed-off-by: Stefan Roese + +commit 5bc542a593abc9e974fbd34704af85c37c366c60 +Author: Victor Gallardo +Date: Thu Aug 28 16:03:28 2008 -0700 + + ppc4xx: fix UIC external_interrupt hang on UIC0 + + This patch fixes a UIC external_interrupt hang if critical or non-critical + interrupt is set at the same time as a normal interrupt is set on UIC0. + + Signed-off-by: Victor Gallardo + Signed-off-by: Stefan Roese + +commit 04737d5ffd16248cb80ab3dd4f3765057a803f18 +Author: Prodyut Hazarika +Date: Wed Aug 27 16:39:00 2008 -0700 + + ppc4xx: Optimizations/Cleanups for IBM DDR2 Memory Controller + + Removed Magic numbers from Initialization preload registers + Tested with Kilauea, Glacier, Canyonlands and Katmai boards + About 5-7% improvement seen for LMBench memtests + + Signed-off-by: Prodyut Hazarika + Signed-off-by: Stefan Roese + +commit 8a490422bed685c9491274ec997f62061d88620b +Author: John Rigby +Date: Thu Aug 28 13:17:07 2008 -0600 + + ADS5121: Fix NOR and CPLD ALE timing for rev 2 silicon + + MPC5121 rev 2 silicon has a new register for controlling how long + CS is asserted after deassertion of ALE in multiplexed mode. + + The default is to assert CS together with ALE. The alternative + is to assert CS (ALEN+1)*LPC_CLK clocks after deassertion of ALE. + + The default is wrong for the NOR flash and CPLD on the ADS5121. + + This patch turns on the alternative for CS0 (NOR) and CS2 (CPLD) + it does so conditionally based on silicon rev 2.0 or greater. + + Signed-off-by: Martha J Marx + Signed-off-by: John Rigby + +commit 5d9a5efa4b332f442b54a755d49969123c3a8742 +Author: TsiChung Liew +Date: Tue Aug 19 00:56:46 2008 +0600 + + Add I2C frequency dividers for ColdFire + + The existing I2C freqency dividers for FDR does not apply + to ColdFire platforms; thus, a seperate table is added + based on MCF5xxx Reference Manual + + Signed-off-by: Luigi 'Comio' Mantellini + Signed-off-by: TsiChung Liew + Acked-by: Tabi Timur + +commit eec567a67e00d1ed8d941e9098b7d421f4091abf +Author: TsiChung Liew +Date: Tue Aug 19 03:01:19 2008 +0600 + + ColdFire: I2C fix for multiple platforms + + Signed-off-by: TsiChung Liew + +commit d53cf6a9c7423cba668b867978648645f71c3090 +Author: TsiChung Liew +Date: Tue Aug 19 00:37:13 2008 +0600 + + ColdFire: Add CONFIG_MII_INIT for M5272C3 + + Signed-off-by: TsiChung Liew + +commit f78ced3028d4130b24a318943a70cf5584ab16f4 +Author: TsiChung Liew +Date: Tue Aug 19 00:26:25 2008 +0600 + + ColdFire: Multiple fixes for MCF5445x platforms + + Add FEC pin set and mii reset in __mii_init(). Change + legacy flash vendor from 2 to AMD LEGACY (0xFFF0), + change cfi_offset to 0, and change CFG_FLASH_CFI to + CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and + M54455EVB env settings in configuration file. + + Signed-off-by: TsiChung Liew + +commit 454e725b3a9537b7f273bbd0cbca180f23a7a6e8 +Author: TsiChung Liew +Date: Fri Aug 15 18:24:25 2008 +0000 + + ColdFire: Change the SDRAM BRD2WT timing from 3 to 7 + + The user manuals recommend 7. + + Signed-off-by: Kurt Mahan + Acked-by: TsiChung Liew + +commit 79e0799cf6e88d98d77b216a55234bf674b59a4e +Author: TsiChung Liew +Date: Fri Aug 15 16:50:07 2008 +0000 + + ColdFire: Raise uart baudrate to 115200 bps + + M5249EVB, M5271EVB, M5272C3, M5275EVB and M5282EVB platforms + uart baudrate increase from 19200 to 115200 bps + + Signed-off-by: TsiChung Liew + +commit ab6ba842682552ccf071d0034da0a20633d1d1ac +Author: TsiChung Liew +Date: Wed Aug 13 12:07:03 2008 +0000 + + ColdFire: Fix board.c warning message + + Implicit declaration of nand_init() warning message + + Signed-off-by: TsiChung Liew + +commit 5798b1c4650e9a8713c95b25c1e669a2bc80a97b +Author: Kumar Gala +Date: Wed Aug 27 01:10:34 2008 -0500 + + FSL DDR: Remove duplicate setting of cs0_bnds register on 86xx. + + Signed-off-by: Kumar Gala + +commit 258c37b147353bc522ffc33dfbd7d0d9cd7c32d7 +Author: Heiko Schocher +Date: Thu Aug 21 20:44:49 2008 +0200 + + mpc52xx: added support for the MPC5200 based MUC.MC52 board from MAN. + + Signed-off-by: Heiko Schocher + +commit 9cff4448a9cb882defe6c8bde73b77fc0c636799 +Author: Kumar Gala +Date: Tue Aug 19 14:46:36 2008 -0500 + + mpc85xx: remove redudant code with lib_ppc/interrupts.c + + For some reason we duplicated the majority of code in lib_ppc/interrupts.c + not show how that happened, but there is no good reason for it. + + Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why + they exist. + + Signed-off-by: Kumar Gala + +commit 9490a7f1a9484617bad75c60807ce02c8a3a6d56 +Author: Kumar Gala +Date: Fri Jul 25 13:31:05 2008 -0500 + + mpc85xx: Add support for the MPC8536DS reference board + + Signed-off-by: Kumar Gala + Signed-off-by: Srikanth Srinivasan + Signed-off-by: Dejan Minic + Signed-off-by: Jason Jin + Signed-off-by: Dave Liu + Signed-off-by: Kumar Gala + +commit ef50d6c06ece74fb17e8d7510e62cad9df8b810d +Author: Kumar Gala +Date: Tue Aug 12 11:14:19 2008 -0500 + + mpc85xx: Add support for the MPC8536 + + The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We + also have SERDES init code for the 8536. + + Signed-off-by: Kumar Gala + Signed-off-by: Srikanth Srinivasan + Signed-off-by: Dejan Minic + Signed-off-by: Jason Jin + Signed-off-by: Dave Liu + +commit 129ba616b3813dde861f25f3d8a3c47c5c36ad5f +Author: Kumar Gala +Date: Tue Aug 12 11:13:08 2008 -0500 + + mpc85xx: Add support for the MPC8572DS reference board + + Signed-off-by: Kumar Gala + +commit 457caecdbca3df21a93abff19eab12dbc61b7897 +Author: Kumar Gala +Date: Wed Aug 27 01:05:35 2008 -0500 + + FSL DDR: Remove old SPD support from cpu/mpc85xx + + All 85xx boards have been converted to the new code so we can + remove the old SPD DDR setup code. + + Signed-off-by: Kumar Gala + +commit 0e7927db138976469e7257e29c1338050a50fcd9 +Author: Kumar Gala +Date: Wed Aug 27 01:04:07 2008 -0500 + + FSL DDR: Convert STXSSA to new DDR code. + + Signed-off-by: Kumar Gala + +commit c360d9b970fbb9c13744c355879671165bbb9b9e +Author: Kumar Gala +Date: Wed Aug 27 01:03:42 2008 -0500 + + FSL DDR: Convert STXGP3 to new DDR code. + + Signed-off-by: Kumar Gala + +commit 8e55313b7ae12352a343f9b9962e662dbd897187 +Author: Kumar Gala +Date: Tue Aug 26 23:52:58 2008 -0500 + + FSL DDR: Convert SBC8560 to new DDR code. + + Signed-off-by: Kumar Gala + +commit 9658bec2e8f55d56ca1be70090ce5a348be4980f +Author: Kumar Gala +Date: Tue Aug 26 23:52:32 2008 -0500 + + FSL DDR: Convert MPC8540EVAL to new DDR code. + + Signed-off-by: Kumar Gala + +commit 6bfa8f723cfd82c55e3ef5620ade396916470a70 +Author: Kumar Gala +Date: Tue Aug 26 23:52:07 2008 -0500 + + FSL DDR: Convert PM856 to new DDR code. + + Signed-off-by: Kumar Gala + +commit d53bd3e17bd4f460257c19255569ea6dcfaae817 +Author: Kumar Gala +Date: Tue Aug 26 23:51:49 2008 -0500 + + FSL DDR: Convert PM854 to new DDR code. + + Signed-off-by: Kumar Gala + +commit 33b9079ba20926f14238fff863b68a98e938948e +Author: Kumar Gala +Date: Tue Aug 26 23:15:28 2008 -0500 + + FSL DDR: Convert sbc8548 to new DDR code. + + Signed-off-by: Kumar Gala + +commit a947e4c7eb15cea1d9fb633955c516aab5ad35dd +Author: Kumar Gala +Date: Tue Aug 26 23:14:14 2008 -0500 + + FSL DDR: Convert atum8548 to new DDR code. + + Signed-off-by: Kumar Gala + +commit be0bd8234b9777ecd63c4c686f72af070d886517 +Author: Kumar Gala +Date: Tue Aug 26 22:56:56 2008 -0500 + + FSL DDR: Convert socrates to new DDR code. + + Signed-off-by: Kumar Gala + +commit 1167a2fd56138b716e01370c4267f3b70bf9ffa0 +Author: Kumar Gala +Date: Tue Aug 26 08:02:30 2008 -0500 + + FSL DDR: Convert MPC8544DS to new DDR code. + + Signed-off-by: Kumar Gala + +commit e6f5b35b41ddbd637bb9ca4ad985b1e0b07dae0e +Author: Jon Loeliger +Date: Tue Mar 18 13:51:05 2008 -0500 + + FSL DDR: Convert MPC8568MDS to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit e31d2c1e2bc954dc32e33bb2076139f85b95f8e6 +Author: Jon Loeliger +Date: Tue Mar 18 13:51:06 2008 -0500 + + FSL DDR: Convert MPC8548CDS to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit aa11d85cf318b961e029fe50d68ca47d004bce93 +Author: Jon Loeliger +Date: Mon Mar 17 15:48:18 2008 -0500 + + FSL DDR: Convert MPC8541CDS to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 2b40edb10d81da7bba724edbccd7f53777112579 +Author: Jon Loeliger +Date: Tue Mar 18 11:12:42 2008 -0500 + + FSL DDR: Convert MPC8555ADS to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 8b625114e8bc5a6b436181167a6e7fcd3303dd2c +Author: Jon Loeliger +Date: Tue Mar 18 11:12:44 2008 -0500 + + FSL DDR: Convert MPC8560ADS to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 9617c8d49a21703eaf13a4033ab1a56eecc033cc +Author: Kumar Gala +Date: Fri Jun 6 13:12:18 2008 -0500 + + FSL DDR: Convert MPC8540ADS to new DDR code. + + Signed-off-by: Kumar Gala + +commit 2a6c2d7ab2a66660f40a6cd3de2eb29ee29d9693 +Author: Kumar Gala +Date: Tue Aug 26 21:34:55 2008 -0500 + + FSL DDR: Add 85xx specific register setting + + Signed-off-by: Kumar Gala + +commit 6fb1b7346849ccd0c20306143e334f5b76143070 +Author: Kumar Gala +Date: Mon Jun 9 11:07:46 2008 -0500 + + FSL DDR: Add e500 TLB helper for DDR code + + Provide a helper function that board code can call to map TLBs when + setting up DDR. + + Signed-off-by: Kumar Gala + +commit d26b739afe5a6760bd345743188759cd9d0f3b47 +Author: Andrew Dyer +Date: Tue Aug 26 17:03:38 2008 -0500 + + dm9000 remove dead external phy support, gpio fix + + dm9000 has code to detect and initialize external phy parts, but later + on in the code the part is forced to use the internal phy + unconditionally. Remove the unused/untested code. + + change the GPIO initialization so that only the GPIO used as an + internal phy reset (hardwired in the chip) is set as an output. The + remaining GPIO need to be handled by board specific code to prevent + possible drive conflicts. Set as inputs for safety. + + replace a few magic numbers with defines + + Signed-off-by: Andrew Dyer + Signed-off-by: Ben Warren + +commit a1573db0c07c8ba99e9c373bb07ecd6f59da672c +Author: Peter Tyser +Date: Tue Aug 26 11:17:48 2008 -0500 + + Standardize bootp, tftpboot, rarpboot, dhcp, and nfs command descriptions + + cmd_net.c command descriptions were updated to describe the optional + hostIPaddr argument. The dhcp command help message was also updated + to more closely reflect the other commands in cmd_net.c + + Signed-off-by: Peter Tyser + Signed-off-by: Ben Warren + +commit 51dfe1382ebaf691485badfa0ea5e75b0710531b +Author: Remy Bohmer +Date: Wed Aug 20 11:30:28 2008 +0200 + + Fix bogus error message in the DHCP handler + + The DHCP handler has 1 state that is not listed in this case, causing a + failure message when there is actually no failure. + + Signed-off-by: Remy Bohmer + Signed-off-by: Ben Warren + +commit 61365501a0e2cae9c1df2818b7b5b3f52c450d18 +Author: Remy Bohmer +Date: Wed Aug 20 11:30:27 2008 +0200 + + Fix compile error when CONFIG_BOOTP_RANDOM_DELAY is set. + + The option CONFIG_BOOTP_RANDOM_DELAY does not compile, because of a + missing extern inside the net/bootp.h header + + Signed-off-by: Remy Bohmer + Signed-off-by: Ben Warren + +commit 1803f7f91ff35ca402259065df7557107dcf28a2 +Author: TsiChung Liew +Date: Tue Aug 19 21:26:32 2008 +0000 + + ColdFire: Add FEC Buffer descriptors in SRAM + + Add FEC Buffer descriptors and data buffer in SRAM for + faster execution and access. + + Signed-off-by: TsiChung Liew + Signed-off-by: Ben Warren + +commit 429be27ce195210d4b9decf9e867b9ca6155a87d +Author: TsiChung Liew +Date: Thu Aug 21 23:55:11 2008 +0000 + + Fix ColdFire FEC warning messages + + Types mismatch and implicit declaration of icache_invalid() + warning messages + + Signed-off-by: TsiChung Liew + Signed-off-by: Ben Warren + +commit 6a002171098e968bd5b362347d2831224fab6048 +Author: Ben Warren +Date: Sat Jul 12 00:17:50 2008 -0700 + + Moved initialization of SKGE Ethernet driver to board code. + + The only board using this driver is the SL8245 board. + Removed initialization for the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 8379f42bc745eb9e4ca551a30fd2d0a63f740d75 +Author: Ben Warren +Date: Sat Jul 12 00:08:45 2008 -0700 + + Moved conditional compilation to Makefile for SK98 Ethernet driver + + Brute-force removal of #ifdefs. Didn't touch the code. + Signed-off-by: Ben Warren + +commit 65d3d99c28dc363d15eaee78225ff643df499b97 +Author: Ben Warren +Date: Fri Jul 11 23:42:19 2008 -0700 + + Moved initialization of ULI526X Ethernet driver to board code. + + The only board using this driver is the Freescale MPC8610HPCD board. + Removed initialization for the driver from net/eth.c + + Signed-off-by: Ben Warren + +commit 914947313a710f5dcf06beaf7f2aa24f1ebcce4f +Author: Ben Warren +Date: Fri Jul 11 23:15:28 2008 -0700 + + Moved initialization of Blackfin EMAC Ethernet controller to board_eth_init() + + Added board_eth_init() function to bf537-stamp board. + Removed initialization for the Blackin EMAC driver from net/eth.c + + Signed-off-by: Ben Warren + +commit fc363ce35408f348cacced68505f3747a53e3d7c +Author: Ben Warren +Date: Wed Jul 9 01:04:19 2008 -0700 + + Moved initialization of GRETH Ethernet driver to CPU directory + + Added a cpu_eth_init() function to leon2/leon3 CPU directories and + removed code from net/eth.c + + Signed-off-by: Ben Warren + +commit 86882b80771309bceb11c6accfd7f6f90ade8bfc +Author: Ben Warren +Date: Tue Aug 26 22:16:25 2008 -0700 + + Moved initialization of MCFFEC Ethernet driver to CPU directory + + Added a cpu_eth_init() function to coldfire CPU directories and + removed code from net/eth.c + + Signed-off-by: Ben Warren + +commit b31da88b9c160d80d42a59cbbb31e24f27184d5c +Author: Ben Warren +Date: Tue Aug 26 22:12:36 2008 -0700 + + Moved initialization of FSL_MCDMAFEC Ethernet driver to CPU directory + + Added a cpu_eth_init() function to cpu/mcf547x_8x directory and + removed code from net/eth.c + + Signed-off-by: Ben Warren + +commit b5710d9974f6f0f3ddb4e67d6cccc262ab37049e +Author: Kumar Gala +Date: Tue Aug 26 15:01:38 2008 -0500 + + FSL DDR: Remove old SPD support from cpu/mpc86xx + + All 86xx boards have been converted to the new code so we can + remove the old SPD DDR setup code. + + Signed-off-by: Kumar Gala + +commit 9bd4e5911b750837515466bc7449087698b88e0e +Author: Kumar Gala +Date: Tue Aug 26 15:01:37 2008 -0500 + + FSL DDR: Convert SBC8641D to new DDR code. + + Signed-off-by: Kumar Gala + +commit 39aa1a73483e1ac2bd56d5523abfc3970ee82c77 +Author: Jon Loeliger +Date: Tue Aug 26 15:01:36 2008 -0500 + + FSL DDR: Convert MPC8610HPCD to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 6a8e5692933e8e6d6e5ba7e594f49dd6d4c3a263 +Author: Kumar Gala +Date: Tue Aug 26 15:01:35 2008 -0500 + + FSL DDR: Convert MPC8641HPCN to new DDR code. + + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 46ff4f1100ea64a01d21cc008ce85ac15eb1821f +Author: Kumar Gala +Date: Tue Aug 26 15:01:34 2008 -0500 + + FSL DDR: Add 86xx specific register setting + + Signed-off-by: Kumar Gala + +commit 233fdd502a6c227f476212b3097653ad48d7e254 +Author: Kumar Gala +Date: Tue Aug 26 15:01:32 2008 -0500 + + FSL DDR: Add DDR2 DIMM paramter support + + Compute DIMM parameters based upon the SPD information. + + Signed-off-by: James Yang + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 05c05a2363a6ac11e0e405926034546ffad71fad +Author: Kumar Gala +Date: Tue Aug 26 15:01:30 2008 -0500 + + FSL DDR: Add DDR1 DIMM paramter support + + Compute DIMM parameters based upon the SPD information in spd. + + Signed-off-by: James Yang + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit 58e5e9aff147e8c7e2bc1406bf9384f65f020ffa +Author: Kumar Gala +Date: Tue Aug 26 15:01:29 2008 -0500 + + FSL DDR: Rewrite the FSL mpc8xxx DDR controller setup code. + + The main purpose of this rewrite it to be able to share the same + initialization code on all FSL PowerPC products that have DDR + controllers. (83xx, 85xx, 86xx). + + The code is broken up into the following steps: + GET_SPD + COMPUTE_DIMM_PARMS + COMPUTE_COMMON_PARMS + GATHER_OPTS + ASSIGN_ADDRESSES + COMPUTE_REGS + PROGRAM_REGS + + This allows us to share more code an easily allow for board specific code + overrides. + + Additionally this code base adds support for >4G of DDR and provides a + foundation for supporting interleaving on processors with more than one + controller. + + Signed-off-by: James Yang + Signed-off-by: Jon Loeliger + Signed-off-by: Becky Bruce + Signed-off-by: Ed Swarthout + Signed-off-by: Kumar Gala + +commit f784e32b4bce0013983506b11af4b85b8ca3d36e +Author: Kumar Gala +Date: Tue Aug 26 15:01:28 2008 -0500 + + FSL DDR: Provide a generic set_ddr_laws() + + Provide a helper function that will setup the last available + LAWs (upto 2) for DDR. Useful for SPD/dyanmic DDR setting code. + + Signed-off-by: Kumar Gala + +commit 0f2cbe3f5eddbdf3848265f35e4f714434929cff +Author: James Yang +Date: Tue Aug 26 15:01:27 2008 -0500 + + Add proper SPD definitions for DDR1/2/3 + + Also adds helper functions for DDR1/2 to verify the checksum. + + Signed-off-by: Kumar Gala + +commit 285db74716c724ae8a0ff177878fd09a74428c7b +Author: Wolfgang Denk +Date: Wed Aug 27 01:02:48 2008 +0200 + + Update CHANGELOG + + Signed-off-by: Wolfgang Denk + commit adf22b66d8bf05bd46e098cf71e6dca29b30aa7b Author: Heiko Schocher Date: Tue Aug 19 10:08:49 2008 +0200