X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=Kconfig;h=1263d0b612dd0668e0264d08b6cdef70bcb97853;hb=4f79d0d32295be8e5137f3093bfa0da764a6a19e;hp=7c8714861286c63f3a855a83967e9e1273684560;hpb=269592719860245f3b3ba3fe48c6cb6c3cabdbb6;p=u-boot

diff --git a/Kconfig b/Kconfig
index 7c87148612..1263d0b612 100644
--- a/Kconfig
+++ b/Kconfig
@@ -57,7 +57,7 @@ config DISTRO_DEFAULTS
 	bool "Select defaults suitable for booting general purpose Linux distributions"
 	default y if ARCH_SUNXI
 	default n
-	select CMD_BOOTZ
+	select CMD_BOOTZ if ARM && !ARM64
 	select CMD_BOOTI if ARM64
 	select CMD_DHCP
 	select CMD_EXT2
@@ -137,74 +137,6 @@ endmenu		# General setup
 
 menu "Boot images"
 
-config SUPPORT_SPL
-	bool
-
-config SUPPORT_TPL
-	bool
-
-config SPL
-	bool
-	depends on SUPPORT_SPL
-	prompt "Enable SPL"
-	help
-	  If you want to build SPL as well as the normal image, say Y.
-
-config SPL_SYS_MALLOC_SIMPLE
-	bool
-	depends on SPL
-	prompt "Only use malloc_simple functions in the SPL"
-	help
-	  Say Y here to only use the *_simple malloc functions from
-	  malloc_simple.c, rather then using the versions from dlmalloc.c;
-	  this will make the SPL binary smaller at the cost of more heap
-	  usage as the *_simple malloc functions do not re-use free-ed mem.
-
-config SPL_STACK_R
-	depends on SPL
-	bool "Enable SDRAM location for SPL stack"
-	help
-	  SPL starts off execution in SRAM and thus typically has only a small
-	  stack available. Since SPL sets up DRAM while in its board_init_f()
-	  function, it is possible for the stack to move there before
-	  board_init_r() is reached. This option enables a special SDRAM
-	  location for the SPL stack. U-Boot SPL switches to this after
-	  board_init_f() completes, and before board_init_r() starts.
-
-config SPL_STACK_R_ADDR
-	depends on SPL_STACK_R
-	hex "SDRAM location for SPL stack"
-	help
-	  Specify the address in SDRAM for the SPL stack. This will be set up
-	  before board_init_r() is called.
-
-config SPL_STACK_R_MALLOC_SIMPLE_LEN
-	depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
-	hex "Size of malloc_simple heap after switching to DRAM SPL stack"
-	default 0x100000
-	help
-	  Specify the amount of the stack to use as memory pool for
-	  malloc_simple after switching the stack to DRAM. This may be set
-	  to give board_init_r() a larger heap then the initial heap in
-	  SRAM which is limited to SYS_MALLOC_F_LEN bytes.
-
-config SPL_SEPARATE_BSS
-	depends on SPL
-	bool "BSS section is in a different memory region from text"
-	help
-	  Some platforms need a large BSS region in SPL and can provide this
-	  because RAM is already set up. In this case BSS can be moved to RAM.
-	  This option should then be enabled so that the correct device tree
-	  location is used. Normally we put the device tree at the end of BSS
-	  but with this option enabled, it goes at _image_binary_end.
-
-config TPL
-	bool
-	depends on SPL && SUPPORT_TPL
-	prompt "Enable TPL"
-	help
-	  If you want to build TPL as well as the normal image and SPL, say Y.
-
 config FIT
 	bool "Support Flattened Image Tree"
 	help
@@ -359,6 +291,33 @@ config FIT_IMAGE_POST_PROCESS
 	  injected into the FIT creation (i.e. the blobs would have been pre-
 	  processed before being added to the FIT image).
 
+config SPL_DFU_SUPPORT
+	bool "Enable SPL with DFU to load binaries to memory device"
+	depends on USB
+	help
+	  Currently the SPL does not have capability to load the
+	  binaries or boot images to boot devices like ram,eMMC,SPI,etc.
+	  This feature enables the DFU (Device Firmware Upgarde) in SPL with
+	  RAM memory device support. The ROM code will load and execute
+	  the SPL built with dfu. The user can load binaries (u-boot/kernel) to
+	  selected device partition from host-pc using dfu-utils.
+		This feature will be useful to flash the binaries to factory
+	  or bare-metal boards using USB interface.
+
+choice
+	bool "DFU device selection"
+	depends on SPL_DFU_SUPPORT
+
+config SPL_DFU_RAM
+	bool "RAM device"
+	depends on SPL_DFU_SUPPORT
+	help
+	 select RAM/DDR memory device for loading binary images
+	 (u-boot/kernel) to the selected device partition using
+	 DFU and execute the u-boot/kernel from RAM.
+
+endchoice
+
 config SYS_CLK_FREQ
 	depends on ARC || ARCH_SUNXI
 	int "CPU clock frequency"