X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=Kconfig;h=821b464db207b60813e326fcb3b014c98a2e98a3;hb=9c42558afb80e46c72bd3852f8fe1c2144726b7b;hp=91a0618dbbea4000c2c0e9c0046f4c9bf1899495;hpb=57c6941b433722ab83a50dab35b8ab5a0954942a;p=u-boot

diff --git a/Kconfig b/Kconfig
index 91a0618dbb..821b464db2 100644
--- a/Kconfig
+++ b/Kconfig
@@ -54,7 +54,7 @@ config CC_OPTIMIZE_FOR_SIZE
 
 config SYS_MALLOC_F
 	bool "Enable malloc() pool before relocation"
-	default 0x400
+	default y if DM
 	help
 	  Before relocation memory is very limited on many platforms. Still,
 	  we can provide a small malloc() pool if needed. Driver model in
@@ -72,13 +72,31 @@ config SYS_MALLOC_F_LEN
 	  initial serial device and any others that are needed.
 
 menuconfig EXPERT
-        bool "Configure standard U-Boot features (expert users)"
-        help
-          This option allows certain base U-Boot options and settings
-          to be disabled or tweaked. This is for specialized
-          environments which can tolerate a "non-standard" U-Boot.
-          Only use this if you really know what you are doing.
-
+	bool "Configure standard U-Boot features (expert users)"
+	default y
+	help
+	  This option allows certain base U-Boot options and settings
+	  to be disabled or tweaked. This is for specialized
+	  environments which can tolerate a "non-standard" U-Boot.
+	  Only use this if you really know what you are doing.
+
+if EXPERT
+	config SYS_MALLOC_CLEAR_ON_INIT
+	bool "Init with zeros the memory reserved for malloc (slow)"
+	default y
+	help
+	  This setting is enabled by default. The reserved malloc
+	  memory is initialized with zeros, so first malloc calls
+	  will return the pointer to the zeroed memory. But this
+	  slows the boot time.
+
+	  It is recommended to disable it, when CONFIG_SYS_MALLOC_LEN
+	  value, has more than few MiB, e.g. when uses bzip2 or bmp logo.
+	  Then the boot time can be significantly reduced.
+	  Warning:
+	  When disabling this, please check if malloc calls, maybe
+	  should be replaced by calloc - if expects zeroed memory.
+endif
 endmenu		# General setup
 
 menu "Boot images"
@@ -96,6 +114,54 @@ config SPL
 	help
 	  If you want to build SPL as well as the normal image, say Y.
 
+config SPL_SYS_MALLOC_SIMPLE
+	bool
+	depends on SPL
+	prompt "Only use malloc_simple functions in the spl"
+	help
+	  Say Y here to only use the *_simple malloc functions from
+	  malloc_simple.c, rather then using the versions from dlmalloc.c
+	  this will make the SPL binary smaller at the cost of more heap
+	  usage as the *_simple malloc functions do not re-use free-ed mem.
+
+config SPL_STACK_R
+	depends on SPL
+	bool "Enable SDRAM location for SPL stack"
+	help
+	  SPL starts off execution in SRAM and thus typically has only a small
+	  stack available. Since SPL sets up DRAM while in its board_init_f()
+	  function, it is possible for the stack to move there before
+	  board_init_r() is reached. This option enables a special SDRAM
+	  location for the SPL stack. U-Boot SPL switches to this after
+	  board_init_f() completes, and before board_init_r() starts.
+
+config SPL_STACK_R_ADDR
+	depends on SPL_STACK_R
+	hex "SDRAM location for SPL stack"
+	help
+	  Specify the address in SDRAM for the SPL stack. This will be set up
+	  before board_init_r() is called.
+
+config SPL_STACK_R_MALLOC_SIMPLE_LEN
+	depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
+	hex "Size of malloc_simple heap after switching to DRAM SPL stack"
+	default 0x100000
+	help
+	  Specify the amount of the stack to use as memory pool for
+	  malloc_simple after switching the stack to DRAM. This may be set
+	  to give board_init_r() a larger heap then the initial heap in
+	  SRAM which is limited to SYS_MALLOC_F_LEN bytes.
+
+config SPL_SEPARATE_BSS
+	depends on SPL
+	bool "BSS section is in a different memory region from text"
+	help
+	  Some platforms need a large BSS region in SPL and can provide this
+	  because RAM is already set up. In this case BSS can be moved to RAM.
+	  This option should then be enabled so that the correct device tree
+	  location is used. Normally we put the device tree at the end of BSS
+	  but with this option enabled, it goes at _image_binary_end.
+
 config TPL
 	bool
 	depends on SPL && SUPPORT_TPL
@@ -110,7 +176,7 @@ config FIT
 	  Flattened Image Tree.  FIT is formally a FDT, which can include
 	  images of various types (kernel, FDT blob, ramdisk, etc.)
 	  in a single blob.  To boot this new uImage structure,
-	  pass the the address of the blob to the "bootm" command.
+	  pass the address of the blob to the "bootm" command.
 
 config FIT_VERBOSE
 	bool "Display verbose messages on FIT boot"
@@ -142,13 +208,14 @@ config SYS_EXTRA_OPTIONS
 	  new boards should not use this option.
 
 config SYS_TEXT_BASE
-	depends on SPARC || ARC
+	depends on SPARC || ARC || X86 || ARCH_UNIPHIER || ARCH_ZYNQMP
+	depends on !EFI_APP
 	hex "Text Base"
 	help
 	  TODO: Move CONFIG_SYS_TEXT_BASE for all the architecture
 
 config SYS_CLK_FREQ
-	depends on ARC
+	depends on ARC || ARCH_SUNXI
 	int "CPU clock frequency"
 	help
 	  TODO: Move CONFIG_SYS_CLK_FREQ for all the architecture