X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=15428643edef7ea77710113f8908002b50328577;hb=874bb7b88fe9b4648e1288a387af2e31014a72f3;hp=6b94f8482c5c55816a9d878c006d1d64f641aa0b;hpb=bb99ad6d8257bf828f150d40f507b30d80a4a7ae;p=u-boot

diff --git a/README b/README
index 6b94f8482c..15428643ed 100644
--- a/README
+++ b/README
@@ -1342,6 +1342,27 @@ The following options need to be configured:
 
 		will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
 
+		CFG_SPD_BUS_NUM
+
+		If defined, then this indicates the I2C bus number for DDR SPD.
+		If not defined, then U-Boot assumes that SPD is on I2C bus 0.
+
+		CFG_RTC_BUS_NUM
+
+		If defined, then this indicates the I2C bus number for the RTC.
+		If not defined, then U-Boot assumes that RTC is on I2C bus 0.
+
+		CFG_DTT_BUS_NUM
+
+		If defined, then this indicates the I2C bus number for the DTT.
+		If not defined, then U-Boot assumes that DTT is on I2C bus 0.
+
+		CONFIG_FSL_I2C
+
+		Define this option if you want to use Freescale's I2C driver in
+		drivers/fsl_i2c.c.
+
+
 - SPI Support:	CONFIG_SPI
 
 		Enables SPI driver (so far only tested with
@@ -1500,8 +1521,8 @@ The following options need to be configured:
 
 		Enable auto completion of commands using TAB.
 
-                Note that this feature has NOT been implemented yet
-                for the "hush" shell.
+		Note that this feature has NOT been implemented yet
+		for the "hush" shell.
 
 
 		CFG_HUSH_PARSER
@@ -2249,6 +2270,14 @@ Low Level (hardware related) configuration options:
 		If SPD EEPROM is on an I2C bus other than the first one, specify here.
 		Note that the value must resolve to something your driver can deal with.
 
+- CFG_83XX_DDR_USES_CS0
+		Only for 83xx systems. If specified, then DDR should be configured
+		using CS0 and CS1 instead of CS2 and CS3.
+
+- CFG_83XX_DDR_USES_CS0
+		Only for 83xx systems. If specified, then DDR should be configured
+		using CS0 and CS1 instead of CS2 and CS3.
+
 - CONFIG_ETHER_ON_FEC[12]
 		Define to enable FEC[12] on a 8xx series processor.
 
@@ -3154,11 +3183,11 @@ loadaddr=200000
 oftaddr=0x300000
 => bootm $loadaddr - $oftaddr
 ## Booting image at 00200000 ...
-   Image Name:   Linux-2.6.17-dirty
-   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
-   Data Size:    1029343 Bytes = 1005.2 kB
+   Image Name:	 Linux-2.6.17-dirty
+   Image Type:	 PowerPC Linux Kernel Image (gzip compressed)
+   Data Size:	 1029343 Bytes = 1005.2 kB
    Load Address: 00000000
-   Entry Point:  00000000
+   Entry Point:	 00000000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
 Booting using flat device tree at 0x300000