X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=246ae2badca47cefc8106de76bc2adfbbee859e4;hb=refs%2Fheads%2FGPL-Cleanup;hp=561c100166da916e3381d7e46a621e828635a7e6;hpb=92afd368bba7d98b2b7bfb51082c3639bb2119b3;p=u-boot diff --git a/README b/README index 561c100166..246ae2badc 100644 --- a/README +++ b/README @@ -603,7 +603,6 @@ The following options need to be configured: CONFIG_CMD_DATE * support for RTC, date/time... CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DOC * Disk-On-Chip Support CONFIG_CMD_DS4510 * ds4510 I2C gpio commands CONFIG_CMD_DS4510_INFO * ds4510 I2C info command CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd @@ -630,6 +629,8 @@ The following options need to be configured: CONFIG_CMD_KGDB * kgdb CONFIG_CMD_LOADB loadb CONFIG_CMD_LOADS loads + CONFIG_CMD_MD5SUM print md5 message digest + (requires CONFIG_CMD_MEMORY and CONFIG_MD5) CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, loop, loopw, mtest CONFIG_CMD_MISC Misc functions like sleep etc @@ -653,6 +654,8 @@ The following options need to be configured: (requires CONFIG_CMD_I2C) CONFIG_CMD_SETGETDCR Support for DCR Register access (4xx only) + CONFIG_CMD_SHA1 print sha1 memory digest + (requires CONFIG_CMD_MEMORY) CONFIG_CMD_SOURCE "source" command Support CONFIG_CMD_SPI * SPI serial bus support CONFIG_CMD_USB * USB support @@ -855,9 +858,13 @@ The following options need to be configured: MPC5200 USB requires additional defines: CONFIG_USB_CLOCK for 528 MHz Clock: 0x0001bbbb + CONFIG_PSC3_USB + for USB on PSC3 CONFIG_USB_CONFIG for differential drivers: 0x00001000 for single ended drivers: 0x00005000 + for differential drivers on PSC3: 0x00000100 + for single ended drivers on PSC3: 0x00004100 CONFIG_SYS_USB_EVENT_POLL May be defined to allow interrupt polling instead of using asynchronous interrupts @@ -1074,6 +1081,26 @@ The following options need to be configured: allows for a "silent" boot where a splash screen is loaded very quickly after power-on. + CONFIG_SPLASH_SCREEN_ALIGN + + If this option is set the splash image can be freely positioned + on the screen. Environment variable "splashpos" specifies the + position as "x,y". If a positive number is given it is used as + number of pixel from left/top. If a negative number is given it + is used as number of pixel from right/bottom. You can also + specify 'm' for centering the image. + + Example: + setenv splashpos m,m + => image at center of screen + + setenv splashpos 30,20 + => image at x = 30 and y = 20 + + setenv splashpos -10,m + => vertically centered image + at x = dspWidth - bmpWidth - 9 + - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP If this option is set, additionally to standard BMP @@ -1165,6 +1192,11 @@ The following options need to be configured: Defines a default value for the IP address of a TFTP server to contact when using the "tftboot" command. + CONFIG_KEEP_SERVERADDR + + Keeps the server's MAC address, in the env 'serveraddr' + for passing to bootargs (like Linux's netconsole option) + - Multicast TFTP Mode: CONFIG_MCAST_TFTP @@ -2428,6 +2460,12 @@ to save the current settings. to a block boundary, and CONFIG_ENV_SIZE must be a multiple of the NAND devices block size. +- CONFIG_NAND_ENV_DST + + Defines address in RAM to which the nand_spl code should copy the + environment. If redundant environment is used, it will be copied to + CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE. + - CONFIG_SYS_SPI_INIT_OFFSET Defines offset to the initial SPI buffer area in DPRAM. The @@ -2702,6 +2740,11 @@ Low Level (hardware related) configuration options: some other boot loader or by a debugger which performs these initializations itself. +- CONFIG_PRELOADER + + Modifies the behaviour of start.S when compiling a loader + that is executed before the actual U-Boot. E.g. when + compiling a NAND SPL. Building the Software: ====================== @@ -3981,15 +4024,15 @@ U-Boot Porting Guide: list, October 2002] -int main (int argc, char *argv[]) +int main(int argc, char *argv[]) { sighandler_t no_more_time; - signal (SIGALRM, no_more_time); - alarm (PROJECT_DEADLINE - toSec (3 * WEEK)); + signal(SIGALRM, no_more_time); + alarm(PROJECT_DEADLINE - toSec (3 * WEEK)); if (available_money > available_manpower) { - pay consultant to port U-Boot; + Pay consultant to port U-Boot; return 0; } @@ -3997,35 +4040,47 @@ int main (int argc, char *argv[]) Subscribe to u-boot mailing list; - if (clueless) { - email ("Hi, I am new to U-Boot, how do I get started?"); - } + if (clueless) + email("Hi, I am new to U-Boot, how do I get started?"); while (learning) { Read the README file in the top level directory; - Read http://www.denx.de/twiki/bin/view/DULG/Manual ; + Read http://www.denx.de/twiki/bin/view/DULG/Manual; + Read applicable doc/*.README; Read the source, Luke; + /* find . -name "*.[chS]" | xargs grep -i */ } - if (available_money > toLocalCurrency ($2500)) { - Buy a BDI2000; - } else { + if (available_money > toLocalCurrency ($2500)) + Buy a BDI3000; + else Add a lot of aggravation and time; - } - Create your own board support subdirectory; - - Create your own board config file; - - while (!running) { - do { - Add / modify source code; - } until (compiles); - Debug; - if (clueless) - email ("Hi, I am having problems..."); + if (a similar board exists) { /* hopefully... */ + cp -a board/ board/ + cp include/configs/.h include/configs/.h + } else { + Create your own board support subdirectory; + Create your own board include/configs/.h file; + } + Edit new board/ files + Edit new include/configs/.h + + while (!accepted) { + while (!running) { + do { + Add / modify source code; + } until (compiles); + Debug; + if (clueless) + email("Hi, I am having problems..."); + } + Send patch file to the U-Boot email list; + if (reasonable critiques) + Incorporate improvements from email list code review; + else + Defend code as written; } - Send patch file to Wolfgang; return 0; }