X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=2c776876e236737f54e3e9b5b72acde4d6938aea;hb=9ef78511cda39987e5fc10febf386fd19f58ecf7;hp=ca415d38b1f7f3c41e54653331a4ba9b4f4a30a1;hpb=cd21a458da20f62807fedbed86b65f2d59d6b611;p=u-boot diff --git a/README b/README index ca415d38b1..2c776876e2 100644 --- a/README +++ b/README @@ -368,8 +368,10 @@ The following options need to be configured: * Adds the "fdt" command * The bootm command automatically updates the fdt - OF_CPU - The proper name of the cpus node. - OF_SOC - The proper name of the soc node. + OF_CPU - The proper name of the cpus node (only required for + MPC512X and MPC5xxx based boards). + OF_SOC - The proper name of the soc node (only required for + MPC512X and MPC5xxx based boards). OF_TBCLK - The timebase frequency. OF_STDOUT_PATH - The path to the console device @@ -386,6 +388,15 @@ The following options need to be configured: This define fills in the correct boot CPU in the boot param header, the default value is zero if undefined. + CONFIG_OF_IDE_FIXUP + + U-Boot can detect if an IDE device is present or not. + If not, and this new config option is activated, U-Boot + removes the ATA node from the DTS before booting Linux, + so the Linux IDE driver does not probe the device and + crash. This is needed for buggy hardware (uc101) where + no pull down resistor is connected to the signal IDE5V_DD7. + - vxWorks boot parameters: bootvx constructs a valid bootline using the following @@ -603,13 +614,13 @@ The following options need to be configured: CONFIG_CMD_DATE * support for RTC, date/time... CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DOC * Disk-On-Chip Support CONFIG_CMD_DS4510 * ds4510 I2C gpio commands CONFIG_CMD_DS4510_INFO * ds4510 I2C info command CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments + CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_EEPROM * EEPROM read/write support CONFIG_CMD_ELF * bootelf, bootvx CONFIG_CMD_SAVEENV saveenv @@ -630,6 +641,8 @@ The following options need to be configured: CONFIG_CMD_KGDB * kgdb CONFIG_CMD_LOADB loadb CONFIG_CMD_LOADS loads + CONFIG_CMD_MD5SUM print md5 message digest + (requires CONFIG_CMD_MEMORY and CONFIG_MD5) CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, loop, loopw, mtest CONFIG_CMD_MISC Misc functions like sleep etc @@ -653,6 +666,8 @@ The following options need to be configured: (requires CONFIG_CMD_I2C) CONFIG_CMD_SETGETDCR Support for DCR Register access (4xx only) + CONFIG_CMD_SHA1 print sha1 memory digest + (requires CONFIG_CMD_MEMORY) CONFIG_CMD_SOURCE "source" command Support CONFIG_CMD_SPI * SPI serial bus support CONFIG_CMD_USB * USB support @@ -855,9 +870,13 @@ The following options need to be configured: MPC5200 USB requires additional defines: CONFIG_USB_CLOCK for 528 MHz Clock: 0x0001bbbb + CONFIG_PSC3_USB + for USB on PSC3 CONFIG_USB_CONFIG for differential drivers: 0x00001000 for single ended drivers: 0x00005000 + for differential drivers on PSC3: 0x00000100 + for single ended drivers on PSC3: 0x00004100 CONFIG_SYS_USB_EVENT_POLL May be defined to allow interrupt polling instead of using asynchronous interrupts @@ -1074,6 +1093,26 @@ The following options need to be configured: allows for a "silent" boot where a splash screen is loaded very quickly after power-on. + CONFIG_SPLASH_SCREEN_ALIGN + + If this option is set the splash image can be freely positioned + on the screen. Environment variable "splashpos" specifies the + position as "x,y". If a positive number is given it is used as + number of pixel from left/top. If a negative number is given it + is used as number of pixel from right/bottom. You can also + specify 'm' for centering the image. + + Example: + setenv splashpos m,m + => image at center of screen + + setenv splashpos 30,20 + => image at x = 30 and y = 20 + + setenv splashpos -10,m + => vertically centered image + at x = dspWidth - bmpWidth - 9 + - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP If this option is set, additionally to standard BMP @@ -1165,6 +1204,11 @@ The following options need to be configured: Defines a default value for the IP address of a TFTP server to contact when using the "tftboot" command. + CONFIG_KEEP_SERVERADDR + + Keeps the server's MAC address, in the env 'serveraddr' + for passing to bootargs (like Linux's netconsole option) + - Multicast TFTP Mode: CONFIG_MCAST_TFTP @@ -1334,6 +1378,13 @@ The following options need to be configured: therefore be cleared to 0 (See, eg, MPC823e User's Manual p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0. + CONFIG_SYS_I2C_INIT_MPC5XXX + + When a board is reset during an i2c bus transfer + chips might think that the current transfer is still + in progress. Reset the slave devices by sending start + commands until the slave device responds. + That's all that's required for CONFIG_HARD_I2C. If you use the software i2c interface (CONFIG_SOFT_I2C) @@ -2969,14 +3020,6 @@ Some configuration options can be set using Environment Variables: configuration from the BOOTP server, but not try to load any image using TFTP - autoscript - if set to "yes" commands like "loadb", "loady", - "bootp", "tftpb", "rarpboot" and "nfs" will attempt - to automatically run script images (by internally - calling "source"). - - autoscript_uname - if script image is in a format (FIT) this - variable is used to get script subimage unit name. - autostart - if set to "yes", an image loaded using the "bootp", "rarpboot", "tftpboot" or "diskboot" commands will be automatically started (by internally calling @@ -3880,10 +3923,10 @@ For PowerPC, the following registers have specific use: average for all boards 752 bytes for the whole U-Boot image, 624 text + 127 data). -On Blackfin, the normal C ABI (except for P5) is followed as documented here: +On Blackfin, the normal C ABI (except for P3) is followed as documented here: http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface - ==> U-Boot will use P5 to hold a pointer to the global data + ==> U-Boot will use P3 to hold a pointer to the global data On ARM, the following registers are used: