X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=660c81284027b2660eb6c7426245424cb749c526;hb=bde0232c731d7fcec5200e48870ff05fbce3dfd9;hp=1bdf1ace06dddad0073ecf50d3ec7bddd91f1f46;hpb=b25862468960c2d830af297bf0405e39b0482961;p=groeck-it87

diff --git a/README b/README
index 1bdf1ac..660c812 100644
--- a/README
+++ b/README
@@ -6,6 +6,10 @@ Supported chips:
     Prefix: 'it8603'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Not publicly available
+  * IT8613E
+    Prefix: 'it8613'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * IT8620E
     Prefix: 'it8620'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -13,6 +17,10 @@ Supported chips:
     Prefix: 'it8622'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Not publicly available
+  * IT8625E
+    Prefix: 'it8625'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * IT8628E
     Prefix: 'it8628'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -87,6 +95,14 @@ Authors:
     Jean Delvare <jdelvare@suse.de>
 
 
+Building & Installing
+---------------------
+
+* make clean
+* make
+* sudo make install
+
+
 Module Parameters
 -----------------
 
@@ -276,3 +292,66 @@ temperature for thermal diodes or diode-connected thermal transistors.
 If a temperature sensor is configured for thermistors, the attribute values
 are ignored. If the thermal sensor type is Intel PECI, the temperature offset
 must be programmed to the critical CPU temperature.
+
+Preliminary support
+-------------------
+
+Support for IT8607E is preliminary. Voltage readings, temperature readings,
+fan control, and fan speed measurements may be wrong and/or missing.
+Fan control and fan speed may be enabled and reported for non-existing
+fans. Please report any problems and inconsistencies.
+
+Reporting information for unsupported chips
+-------------------------------------------
+
+If the chip in your system is not yet supported by the driver, please provide
+the following information.
+
+First, run sensors-detect. It will tell you something like
+
+    Probing for Super-I/O at 0x2e/0x2f
+    ...
+    Trying family `ITE'...                                      Yes
+    Found unknown chip with ID 0x8665
+	(logical device 4 has address 0x290, could be sensors)
+
+With this information, run the following commands.
+
+sudo isadump -k 0x87,0x01,0x55,0x55 0x2e 0x2f 7
+sudo isadump 0x295 0x296
+
+and report the results.
+
+The addresses in the first command are from "Probing for Super-I/O at
+0x2e/0x2f". Use those addresses in the first command.
+    sudo isadump -k 0x87,0x01,0x55,0x55 0x2e 0x2f 7
+
+The addresses in the second command are from "has address 0x290".
+Add 5 and 6 to this address for the next command.
+    sudo isadump 0x295 0x296
+
+Next, force-install the driver by providing one of the already supported chips
+as forced ID. Useful IDs to test are 0x8622, 0x8628, 0x8728, and 0x8732, though
+feel free to test more IDs. For each ID, instantiate the driver as follows
+(this example is instantiating driver with ID 0x8622).
+	sudo modprobe it87 force_id=0x8622
+After entering this command, run the "sensors" command and provide the output.
+Then unload the driver with
+	sudo modprobe -r it87
+Repeat with different chip IDs, and report each result.
+
+Please also report your board type as well as voltages and fan settings from
+the BIOS. If possible, connect fans to different fan headers and let us know
+if all fans are detected and reported.
+
+This information _might_ give us enough information to add experimental support
+for the chip in question. No guarantees, though - unless a datasheet is
+available, something is likely to be wrong.
+
+A note on sensors-detect
+========================
+
+There is a persistent perception that changes in this driver would have impact
+on the output of sensors-detect. This is not the case. sensors-detect is an
+independent application. Changes in this driver do not affect sensors-detect,
+and changes in sensors-detect do not affect this driver.