X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=68d6a499c09f8166baa475f575bdd29ebebc59be;hb=bae5b97e8ec0fedb50350a14e76648714bc51c99;hp=f4892fac31088e9bd7c112860a5028d97021ce46;hpb=5371d34c63aa5d26b323de4f0c99b76445ba486e;p=u-boot

diff --git a/README b/README
index f4892fac31..68d6a499c0 100644
--- a/README
+++ b/README
@@ -1361,7 +1361,7 @@ The following options need to be configured:
 
 - PWM Support:
 		CONFIG_PWM_IMX
-		Support for PWM modul on the imx6.
+		Support for PWM module on the imx6.
 
 - TPM Support:
 		CONFIG_TPM
@@ -2280,8 +2280,6 @@ CBFS (Coreboot Filesystem) support
 		  - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
 		  - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
 		  - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
-		  - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
-		  - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
 		  - CONFIG_SYS_I2C_SH_NUM_CONTROLLERS for number of i2c buses
 
 		- drivers/i2c/omap24xx_i2c.c
@@ -2335,10 +2333,7 @@ CBFS (Coreboot Filesystem) support
 		additional defines:
 
 		CONFIG_SYS_NUM_I2C_BUSES
-		Hold the number of i2c buses you want to use. If you
-		don't use/have i2c muxes on your i2c bus, this
-		is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can
-		omit this define.
+		Hold the number of i2c buses you want to use.
 
 		CONFIG_SYS_I2C_DIRECT_BUS
 		define this, if you don't use i2c muxes on your hardware.
@@ -2552,7 +2547,7 @@ CBFS (Coreboot Filesystem) support
 		will skip addresses 0x50 and 0x68 on a board with one I2C bus
 
 			#define CONFIG_I2C_MULTI_BUS
-			#define CONFIG_SYS_I2C_MULTI_NOPROBES	{{0,0x50},{0,0x68},{1,0x54}}
+			#define CONFIG_SYS_I2C_NOPROBES	{{0,0x50},{0,0x68},{1,0x54}}
 
 		will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
 
@@ -4492,7 +4487,7 @@ Low Level (hardware related) configuration options:
 		CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
 		data is located at the end of the available space
 		(sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
-		CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
+		GENERATED_GBL_DATA_SIZE), and the initial stack is just
 		below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
 		CONFIG_SYS_GBL_DATA_OFFSET) downward.
 
@@ -4551,11 +4546,6 @@ Low Level (hardware related) configuration options:
 		enable SPI microcode relocation patch (MPC8xx);
 		define relocation offset in DPRAM [SCC4]
 
-- CONFIG_SYS_USE_OSCCLK:
-		Use OSCM clock mode on MBX8xx board. Be careful,
-		wrong setting might damage your board. Read
-		doc/README.MBX before setting this variable!
-
 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
 		Offset of the bootmode word in DPRAM used by post
 		(Power On Self Tests). This definition overrides