X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=6f98e09e680d539246c279a18059c2f38ad7ce10;hb=83a1f933d141ca5db69344559c1eef255d45fddd;hp=5cf90a482a8f2056e1fc69b75aa825bffe5ae19f;hpb=bec8c647bc263d80040413a09f54751bc27c9d31;p=u-boot

diff --git a/README b/README
index 5cf90a482a..6f98e09e68 100644
--- a/README
+++ b/README
@@ -812,14 +812,6 @@ The following options need to be configured:
 		CONFIG_AT91_HW_WDT_TIMEOUT
 		specify the timeout in seconds. default 2 seconds.
 
-- U-Boot Version:
-		CONFIG_VERSION_VARIABLE
-		If this variable is defined, an environment variable
-		named "ver" is created by U-Boot showing the U-Boot
-		version as printed by the "version" command.
-		Any change to this variable will be reverted at the
-		next reset.
-
 - Real-Time Clock:
 
 		When CONFIG_CMD_DATE is selected, the type of the RTC
@@ -1420,10 +1412,6 @@ The following options need to be configured:
 		be at least 4MB.
 
 - MII/PHY support:
-		CONFIG_PHY_ADDR
-
-		The address of PHY on MII bus.
-
 		CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
 		The clock frequency of the MII bus
@@ -2217,12 +2205,6 @@ The following options need to be configured:
 		the environment like the "source" command or the
 		boot command first.
 
-		CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-
-		Define this in order to add variables describing certain
-		run-time determined information about the hardware to the
-		environment.  These will be named board_name, board_rev.
-
 		CONFIG_DELAY_ENVIRONMENT
 
 		Normally the environment is loaded when the board is
@@ -2486,12 +2468,6 @@ FIT uImage format:
 		kernel. Needed for UBI support.
 
 - UBI support
-		CONFIG_UBI_SILENCE_MSG
-
-		Make the verbose messages from UBI stop printing.  This leaves
-		warnings and errors enabled.
-
-
 		CONFIG_MTD_UBI_WL_THRESHOLD
 		This parameter defines the maximum difference between the highest
 		erase counter value and the lowest erase counter value of eraseblocks
@@ -2553,12 +2529,6 @@ FIT uImage format:
 		Enable UBI fastmap debug
 		default: 0
 
-- UBIFS support
-		CONFIG_UBIFS_SILENCE_MSG
-
-		Make the verbose messages from UBIFS stop printing.  This leaves
-		warnings and errors enabled.
-
 - SPL framework
 		CONFIG_SPL
 		Enable building of SPL globally.
@@ -2818,9 +2788,6 @@ Configuration Settings:
 		Begin and End addresses of the area used by the
 		simple memory test.
 
-- CONFIG_SYS_ALT_MEMTEST:
-		Enable an alternate, more extensive memory test.
-
 - CONFIG_SYS_MEMTEST_SCRATCH:
 		Scratch address used by the alternate memory test
 		You only need to set this if address zero isn't writeable
@@ -3446,9 +3413,6 @@ Low Level (hardware related) configuration options:
 		If defined, the x86 reset vector code is included. This is not
 		needed when U-Boot is running from Coreboot.
 
-- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
-		Enables the RTC32K OSC on AM33xx based plattforms
-
 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
 		Option to disable subpage write in NAND driver
 		driver that uses this: