X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=86c1304f91b1567ce26d67df13580743099a849e;hb=20cc06611ea33fc0a67a5e56e6476379d2de3091;hp=9455fa76077706532ab782bc35a5a3f36e75eb38;hpb=d1e990ce0f9b98e81338c8627d41aff2268eb464;p=u-boot diff --git a/README b/README index 9455fa7607..86c1304f91 100644 --- a/README +++ b/README @@ -381,6 +381,24 @@ The following options need to be configured: This define fills in the correct boot CPU in the boot param header, the default value is zero if undefined. +- vxWorks boot parameters: + + bootvx constructs a valid bootline using the following + environments variables: bootfile, ipaddr, serverip, hostname. + It loads the vxWorks image pointed bootfile. + + CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name + CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address + CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server + CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters + + CONFIG_SYS_VXWORKS_ADD_PARAMS + + Add it at the end of the bootline. E.g "u=username pw=secret" + + Note: If a "bootargs" environment is defined, it will overwride + the defaults discussed just above. + - Serial Ports: CONFIG_PL010_SERIAL @@ -574,6 +592,10 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DOC * Disk-On-Chip Support + CONFIG_CMD_DS4510 * ds4510 I2C gpio commands + CONFIG_CMD_DS4510_INFO * ds4510 I2C info command + CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd + CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EEPROM * EEPROM read/write support @@ -603,6 +625,8 @@ The following options need to be configured: CONFIG_CMD_MII * MII utility commands CONFIG_CMD_NAND * NAND support CONFIG_CMD_NET bootp, tftpboot, rarpboot + CONFIG_CMD_PCA953X * PCA953x I2C gpio commands + CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command CONFIG_CMD_PCI * pciinfo CONFIG_CMD_PCMCIA * PCMCIA support CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network @@ -680,6 +704,13 @@ The following options need to be configured: Note that if the RTC uses I2C, then the I2C interface must also be configured. See I2C Support, below. +- GPIO Support: + CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO + CONFIG_PCA953X_INFO - enable pca953x info command + + Note that if the GPIO device uses I2C, then the I2C interface + must also be configured. See I2C Support, below. + - Timestamp Support: When CONFIG_TIMESTAMP is selected, the timestamp @@ -1478,6 +1509,15 @@ The following options need to be configured: Bus on the MPC8260. But it should be not so difficult to add this option to other architectures. + CONFIG_SOFT_I2C_READ_REPEATED_START + + defining this will force the i2c_read() function in + the soft_i2c driver to perform an I2C repeated start + between writing the address pointer and reading the + data. If this define is omitted the default behaviour + of doing a stop-start sequence will be used. Most I2C + devices can use either method, but some require one or + the other. - SPI Support: CONFIG_SPI @@ -2005,6 +2045,9 @@ Configuration Settings: - CONFIG_SYS_LONGHELP: Defined when you want long help messages included; undefine this when you're short of memory. +- CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default + width of the commands listed in the 'help' command output. + - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to prompt for user input. @@ -2157,6 +2200,11 @@ Configuration Settings: This option also enables the building of the cfi_flash driver in the drivers directory +- CONFIG_FLASH_CFI_MTD + This option enables the building of the cfi_mtd driver + in the drivers directory. The driver exports CFI flash + to the MTD layer. + - CONFIG_SYS_FLASH_USE_BUFFER_WRITE Use buffered writes to flash. @@ -3708,7 +3756,7 @@ MPC826x processors), on others (parts of) the data cache can be locked as (mis-) used as memory, etc. Chris Hallinan posted a good summary of these issues to the - u-boot-users mailing list: + U-Boot mailing list: Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)? From: "Chris Hallinan" @@ -3918,7 +3966,7 @@ int main (int argc, char *argv[]) Download latest U-Boot source; - Subscribe to u-boot-users mailing list; + Subscribe to u-boot mailing list; if (clueless) { email ("Hi, I am new to U-Boot, how do I get started?"); @@ -3995,10 +4043,11 @@ Since the number of patches for U-Boot is growing, we need to establish some rules. Submissions which do not conform to these rules may be rejected, even when they contain important and valuable stuff. -Patches shall be sent to the u-boot-users mailing list. - Please see http://www.denx.de/wiki/U-Boot/Patches for details. +Patches shall be sent to the u-boot mailing list ; +see http://lists.denx.de/mailman/listinfo/u-boot + When you send a patch, please include the following information with it: @@ -4061,7 +4110,7 @@ Notes: disabled must not need more memory than the old code without your modification. -* Remember that there is a size limit of 40 kB per message on the - u-boot-users mailing list. Bigger patches will be moderated. If - they are reasonable and not bigger than 100 kB, they will be - acknowledged. Even bigger patches should be avoided. +* Remember that there is a size limit of 100 kB per message on the + u-boot mailing list. Bigger patches will be moderated. If they are + reasonable and not too big, they will be acknowledged. But patches + bigger than the size limit should be avoided.