X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=8f0b38cbf38b16de6f2a9d8707cde096f3b52b51;hb=8ad59c9a7bef49a18078888ad8eba8e87737c3b2;hp=9c6d058ef0e5646c5db6cbf8a216794396afec07;hpb=2035d77d790044f389a18c0e6baa05e86d4b32a0;p=u-boot diff --git a/README b/README index 9c6d058ef0..8f0b38cbf3 100644 --- a/README +++ b/README @@ -423,16 +423,50 @@ The following options need to be configured: CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT This value denotes start offset of DSP CCSR space. - CONFIG_SYS_FSL_DDR_EMU - Specify emulator support for DDR. Some DDR features such as - deskew training are not available. - - Generic CPU options: CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN Defines the endianess of the CPU. Implementation of those values is arch specific. + CONFIG_SYS_FSL_DDR + Freescale DDR driver in use. This type of DDR controller is + found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core + SoCs. + + CONFIG_SYS_FSL_DDR_ADDR + Freescale DDR memory-mapped register base. + + CONFIG_SYS_FSL_DDR_EMU + Specify emulator support for DDR. Some DDR features such as + deskew training are not available. + + CONFIG_SYS_FSL_DDRC_GEN1 + Freescale DDR1 controller. + + CONFIG_SYS_FSL_DDRC_GEN2 + Freescale DDR2 controller. + + CONFIG_SYS_FSL_DDRC_GEN3 + Freescale DDR3 controller. + + CONFIG_SYS_FSL_DDRC_ARM_GEN3 + Freescale DDR3 controller for ARM-based SoCs. + + CONFIG_SYS_FSL_DDR1 + Board config to use DDR1. It can be enabled for SoCs with + Freescale DDR1 or DDR2 controllers, depending on the board + implemetation. + + CONFIG_SYS_FSL_DDR2 + Board config to use DDR2. It can be eanbeld for SoCs with + Freescale DDR2 or DDR3 controllers, depending on the board + implementation. + + CONFIG_SYS_FSL_DDR3 + Board config to use DDR3. It can be enabled for SoCs with + Freescale DDR3 controllers. + - Intel Monahans options: CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO @@ -784,6 +818,22 @@ The following options need to be configured: as a convenience, when switching between booting from RAM and NFS. +- Bootcount: + CONFIG_BOOTCOUNT_LIMIT + Implements a mechanism for detecting a repeating reboot + cycle, see: + http://www.denx.de/wiki/view/DULG/UBootBootCountLimit + + CONFIG_BOOTCOUNT_ENV + If no softreset save registers are found on the hardware + "bootcount" is stored in the environment. To prevent a + saveenv on all reboots, the environment variable + "upgrade_available" is used. If "upgrade_available" is + 0, "bootcount" is always 0, if "upgrade_available" is + 1 "bootcount" is incremented in the environment. + So the Userspace Applikation must set the "upgrade_available" + and "bootcount" variable to 0, if a boot was successfully. + - Pre-Boot Commands: CONFIG_PREBOOT @@ -1963,6 +2013,21 @@ CBFS (Coreboot Filesystem) support kernel). Defining CONFIG_STATUS_LED enables this feature in U-Boot. + Additional options: + + CONFIG_GPIO_LED + The status LED can be connected to a GPIO pin. + In such cases, the gpio_led driver can be used as a + status LED backend implementation. Define CONFIG_GPIO_LED + to include the gpio_led driver in the U-Boot binary. + + CONFIG_GPIO_LED_INVERTED_TABLE + Some GPIO connected LEDs may have inverted polarity in which + case the GPIO high value corresponds to LED off state and + GPIO low value corresponds to LED on state. + In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined + with a list of GPIO LEDs that have inverted polarity. + - CAN Support: CONFIG_CAN_DRIVER Defining CONFIG_CAN_DRIVER enables CAN driver support @@ -2058,6 +2123,30 @@ CBFS (Coreboot Filesystem) support - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5 - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses + - drivers/i2c/omap24xx_i2c.c + - activate this driver with CONFIG_SYS_I2C_OMAP24XX + - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0 + - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0 + - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1 + - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1 + - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2 + - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2 + - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3 + - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3 + - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4 + - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4 + + - drivers/i2c/zynq_i2c.c + - activate this driver with CONFIG_SYS_I2C_ZYNQ + - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting + - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr + + - drivers/i2c/s3c24x0_i2c.c: + - activate this driver with CONFIG_SYS_I2C_S3C24X0 + - This driver adds i2c buses (11 for Exynos5250, Exynos5420 + 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung) + with a fix speed from 100000 and the slave addr 0! + additional defines: CONFIG_SYS_NUM_I2C_BUSES @@ -3164,7 +3253,7 @@ FIT uImage format: CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT Set for the SPL on PPC mpc8xxx targets, support for - arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary. + drivers/ddr/fsl/libddr.o in SPL binary. CONFIG_SPL_COMMON_INIT_DDR Set for common ddr init with serial presence detect in @@ -4321,6 +4410,9 @@ Low Level (hardware related) configuration options: NOTE : currently only supported on AM335x platforms. +- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC: + Enables the RTC32K OSC on AM33xx based plattforms + Freescale QE/FMAN Firmware Support: -----------------------------------