X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=a620f0a474465bf64b6f3a2bf9a795b9bf5a6316;hb=86cfb6bdecc3a312a939bbd89560f500f45193c3;hp=98dbe98c2ef5eee54256790eb24998a81ae720cb;hpb=7de0fe1ac330399afc1873e11061668a93cf4fb9;p=u-boot diff --git a/README b/README index 98dbe98c2e..a620f0a474 100644 --- a/README +++ b/README @@ -842,7 +842,8 @@ The following options need to be configured: CONFIG_CMD_I2C * I2C serial bus support CONFIG_CMD_IDE * IDE harddisk support CONFIG_CMD_IMI iminfo - CONFIG_CMD_IMLS List all found images + CONFIG_CMD_IMLS List all images found in NOR flash + CONFIG_CMD_IMLS_NAND List all images found in NAND flash CONFIG_CMD_IMMAP * IMMR dump support CONFIG_CMD_IMPORTENV * import an environment CONFIG_CMD_INI * import data from an ini file into the env @@ -857,8 +858,10 @@ The following options need to be configured: CONFIG_CMD_LOADS loads CONFIG_CMD_MD5SUM print md5 message digest (requires CONFIG_CMD_MEMORY and CONFIG_MD5) + CONFIG_CMD_MEMINFO * Display detailed memory information CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, - loop, loopw, mtest + loop, loopw + CONFIG_CMD_MEMTEST mtest CONFIG_CMD_MISC Misc functions like sleep etc CONFIG_CMD_MMC * MMC memory mapped support CONFIG_CMD_MII * MII utility commands @@ -875,6 +878,7 @@ The following options need to be configured: CONFIG_CMD_READ * Read raw data from partition CONFIG_CMD_REGINFO * Register dump CONFIG_CMD_RUN run command in env variable + CONFIG_CMD_SANDBOX * sb command to access sandbox features CONFIG_CMD_SAVES * save S record dump CONFIG_CMD_SCSI * SCSI Support CONFIG_CMD_SDRAM * print SDRAM configuration information @@ -2386,6 +2390,15 @@ CBFS (Coreboot Filesystem) support run-time determined information about the hardware to the environment. These will be named board_name, board_rev. + CONFIG_DELAY_ENVIRONMENT + + Normally the environment is loaded when the board is + intialised so that it is available to U-Boot. This inhibits + that so that the environment is not available until + explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL + this is instead controlled by the value of + /config/load-environment. + - DataFlash Support: CONFIG_HAS_DATAFLASH @@ -2412,6 +2425,11 @@ CBFS (Coreboot Filesystem) support CONFIG_SF_DEFAULT_MODE (see include/spi.h) CONFIG_SF_DEFAULT_SPEED in Hz + CONFIG_CMD_SF_TEST + + Define this option to include a destructive SPI flash + test ('sf test'). + - SystemACE Support: CONFIG_SYSTEMACE @@ -2699,10 +2717,13 @@ FIT uImage format: CONFIG_FB_ADDR Define CONFIG_FB_ADDR if you want to use specific - address for frame buffer. - Then system will reserve the frame buffer address to - defined address instead of lcd_setmem (this function - grabs the memory for frame buffer by panel's size). + address for frame buffer. This is typically the case + when using a graphics controller has separate video + memory. U-Boot will then place the frame buffer at + the given address instead of dynamically reserving it + in system RAM by calling lcd_setmem(), which grabs + the memory for the frame buffer depending on the + configured panel size. Please see board_init_f function. @@ -2801,6 +2822,12 @@ FIT uImage format: CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME Filename to read to load U-Boot when reading from FAT + CONFIG_SPL_MPC83XX_WAIT_FOR_NAND + Set this for NAND SPL on PPC mpc83xx targets, so that + start.S waits for the rest of the SPL to load before + continuing (the hardware starts execution after just + loading the first page rather than the full 4K). + CONFIG_SPL_NAND_BASE Include nand_base.c in the SPL. Requires CONFIG_SPL_NAND_DRIVERS. @@ -2858,6 +2885,10 @@ FIT uImage format: CONFIG_SPL_LIBGENERIC_SUPPORT Support for lib/libgeneric.o in SPL binary + CONFIG_SPL_PAD_TO + Linker address to which the SPL should be padded before + appending the SPL payload. + CONFIG_SPL_TARGET Final target image containing SPL and payload. Some SPLs use an arch-specific makefile fragment instead, for @@ -3181,6 +3212,23 @@ Configuration Settings: If defined, don't allow the -f switch to env set override variable access flags. +- CONFIG_SYS_GENERIC_BOARD + This selects the architecture-generic board system instead of the + architecture-specific board files. It is intended to move boards + to this new framework over time. Defining this will disable the + arch/foo/lib/board.c file and use common/board_f.c and + common/board_r.c instead. To use this option your architecture + must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in + its config.mk file). If you find problems enabling this option on + your board please report the problem and send patches! + +- CONFIG_SYS_SYM_OFFSETS + This is set by architectures that use offsets for link symbols + instead of absolute values. So bss_start is obtained using an + offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than + directly. You should not need to touch this setting. + + The following definitions that deal with the placement and management of environment data (variable area); in general, we support the following configurations: @@ -3456,6 +3504,16 @@ use the "saveenv" command to store a valid environment. space for already greatly restricted images, including but not limited to NAND_SPL configurations. +- CONFIG_DISPLAY_BOARDINFO + Display information about the board that U-Boot is running on + when U-Boot starts up. The board function checkboard() is called + to do this. + +- CONFIG_DISPLAY_BOARDINFO_LATE + Similar to the previous option, but display this information + later, once stdio is running and output goes to the LCD, if + present. + Low Level (hardware related) configuration options: --------------------------------------------------- @@ -3772,20 +3830,24 @@ Low Level (hardware related) configuration options: that is executed before the actual U-Boot. E.g. when compiling a NAND SPL. +- CONFIG_ARCH_MAP_SYSMEM + Generally U-Boot (and in particular the md command) uses + effective address. It is therefore not necessary to regard + U-Boot address as virtual addresses that need to be translated + to physical addresses. However, sandbox requires this, since + it maintains its own little RAM buffer which contains all + addressable memory. This option causes some memory accesses + to be mapped through map_sysmem() / unmap_sysmem(). + - CONFIG_USE_ARCH_MEMCPY CONFIG_USE_ARCH_MEMSET If these options are used a optimized version of memcpy/memset will be used if available. These functions may be faster under some conditions but may increase the binary size. -- CONFIG_X86_NO_RESET_VECTOR - If defined, the x86 reset vector code is excluded. You will need - to do this when U-Boot is running from Coreboot. - -- CONFIG_X86_NO_REAL_MODE - If defined, x86 real mode code is omitted. This assumes a - 32-bit environment where such code is not needed. You will - need to do this when U-Boot is running from Coreboot. +- CONFIG_X86_RESET_VECTOR + If defined, the x86 reset vector code is included. This is not + needed when U-Boot is running from Coreboot. Freescale QE/FMAN Firmware Support: