X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=d832bcbb7c62e5bef5dbac9d36ebc6c4a6e60495;hb=cce717a96c5840b0cf33e30c87fb1f2b8d633ee3;hp=14c83f4bb1796698e3a88b192a390395c51febeb;hpb=8dc16cf9dd6196d99969d12741df186a61a2f9a3;p=u-boot

diff --git a/README b/README
index 14c83f4bb1..d832bcbb7c 100644
--- a/README
+++ b/README
@@ -898,6 +898,7 @@ The following options need to be configured:
 		CONFIG_CMD_SF		* Read/write/erase SPI NOR flash
 		CONFIG_CMD_SHA1SUM	  print sha1 memory digest
 					  (requires CONFIG_CMD_MEMORY)
+		CONFIG_CMD_SOFTSWITCH	* Soft switch setting command for BF60x
 		CONFIG_CMD_SOURCE	  "source" command Support
 		CONFIG_CMD_SPI		* SPI serial bus support
 		CONFIG_CMD_TFTPSRV	* TFTP transfer in server mode
@@ -930,6 +931,13 @@ The following options need to be configured:
 
 		XXX - this list needs to get updated!
 
+- Regular expression support:
+		CONFIG_REGEX
+                If this variable is defined, U-Boot is linked against
+                the SLRE (Super Light Regular Expression) library,
+                which adds regex support to some commands, as for
+                example "env grep" and "setexpr".
+
 - Device tree:
 		CONFIG_OF_CONTROL
 		If this variable is defined, U-Boot will use a device tree
@@ -2831,8 +2839,18 @@ FIT uImage format:
 		CONFIG_SPL_LDSCRIPT
 		LDSCRIPT for linking the SPL binary.
 
+		CONFIG_SPL_MAX_FOOTPRINT
+		Maximum size in memory allocated to the SPL, BSS included.
+		When defined, the linker checks that the actual memory
+		used by SPL from _start to __bss_end does not exceed it.
+		CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
+		must not be both defined at the same time.
+
 		CONFIG_SPL_MAX_SIZE
-		Maximum binary size (text, data and rodata) of the SPL binary.
+		Maximum size of the SPL image (text, data, rodata, and
+		linker lists sections), BSS excluded.
+		When defined, the linker checks that the actual size does
+		not exceed it.
 
 		CONFIG_SPL_TEXT_BASE
 		TEXT_BASE for linking the SPL binary.
@@ -2845,7 +2863,11 @@ FIT uImage format:
 		Link address for the BSS within the SPL binary.
 
 		CONFIG_SPL_BSS_MAX_SIZE
-		Maximum binary size of the BSS section of the SPL binary.
+		Maximum size in memory allocated to the SPL BSS.
+		When defined, the linker checks that the actual memory used
+		by SPL from __bss_start to __bss_end does not exceed it.
+		CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
+		must not be both defined at the same time.
 
 		CONFIG_SPL_STACK
 		Adress of the start of the stack SPL will use
@@ -2975,6 +2997,12 @@ FIT uImage format:
 		use an arch-specific makefile fragment instead, for
 		example if more than one image needs to be produced.
 
+		CONFIG_FIT_SPL_PRINT
+		Printing information about a FIT image adds quite a bit of
+		code to SPL. So this is normally disabled in SPL. Use this
+		option to re-enable it. This will affect the output of the
+		bootm command when booting a FIT image.
+
 Modem Support:
 --------------
 
@@ -3234,6 +3262,15 @@ Configuration Settings:
 		digits and dots.  Recommended value: 45 (9..1) for 80
 		column displays, 15 (3..1) for 40 column displays.
 
+- CONFIG_FLASH_VERIFY
+		If defined, the content of the flash (destination) is compared
+		against the source after the write operation. An error message
+		will be printed when the contents are not identical.
+		Please note that this option is useless in nearly all cases,
+		since such flash programming errors usually are detected earlier
+		while unprotecting/erasing/programming. Please only enable
+		this option if you really know what you are doing.
+
 - CONFIG_SYS_RX_ETH_BUFFER:
 		Defines the number of Ethernet receive buffers. On some
 		Ethernet controllers it is recommended to set this value