X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=df1d5d67b4ad72f9aab79b7195609423e3c6d64f;hb=20fccb944b987877b5a372c0d0641cf7aafff066;hp=ed79298fd4ea9f09911ac5bbc7860da870d9055a;hpb=81cf7c8d45935a295991fe2cd1df286f0f47511f;p=u-boot

diff --git a/README b/README
index ed79298fd4..df1d5d67b4 100644
--- a/README
+++ b/README
@@ -1,9 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
 #
 # (C) Copyright 2000 - 2013
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
 
 Summary:
 ========
@@ -812,14 +810,6 @@ The following options need to be configured:
 		CONFIG_AT91_HW_WDT_TIMEOUT
 		specify the timeout in seconds. default 2 seconds.
 
-- U-Boot Version:
-		CONFIG_VERSION_VARIABLE
-		If this variable is defined, an environment variable
-		named "ver" is created by U-Boot showing the U-Boot
-		version as printed by the "version" command.
-		Any change to this variable will be reverted at the
-		next reset.
-
 - Real-Time Clock:
 
 		When CONFIG_CMD_DATE is selected, the type of the RTC
@@ -1182,10 +1172,6 @@ The following options need to be configured:
 		CONFIG_SUPPORT_EMMC_BOOT
 		Enable some additional features of the eMMC boot partitions.
 
-		CONFIG_SUPPORT_EMMC_RPMB
-		Enable the commands for reading, writing and programming the
-		key for the Replay Protection Memory Block partition in eMMC.
-
 - USB Device Firmware Update (DFU) class support:
 		CONFIG_DFU_OVER_USB
 		This enables the USB portion of the DFU USB class
@@ -2213,12 +2199,6 @@ The following options need to be configured:
 		the environment like the "source" command or the
 		boot command first.
 
-		CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-
-		Define this in order to add variables describing certain
-		run-time determined information about the hardware to the
-		environment.  These will be named board_name, board_rev.
-
 		CONFIG_DELAY_ENVIRONMENT
 
 		Normally the environment is loaded when the board is
@@ -2427,19 +2407,6 @@ FIT uImage format:
  -150	common/cmd_nand.c	Incorrect FIT image format
   151	common/cmd_nand.c	FIT image format OK
 
-- legacy image format:
-		CONFIG_IMAGE_FORMAT_LEGACY
-		enables the legacy image format support in U-Boot.
-
-		Default:
-		enabled if CONFIG_FIT_SIGNATURE is not defined.
-
-		CONFIG_DISABLE_IMAGE_LEGACY
-		disable the legacy image format
-
-		This define is introduced, as the legacy image format is
-		enabled per default for backward compatibility.
-
 - Standalone program support:
 		CONFIG_STANDALONE_LOAD_ADDR
 
@@ -2724,7 +2691,7 @@ FIT uImage format:
 		use an arch-specific makefile fragment instead, for
 		example if more than one image needs to be produced.
 
-		CONFIG_FIT_SPL_PRINT
+		CONFIG_SPL_FIT_PRINT
 		Printing information about a FIT image adds quite a bit of
 		code to SPL. So this is normally disabled in SPL. Use this
 		option to re-enable it. This will affect the output of the
@@ -2802,9 +2769,6 @@ Configuration Settings:
 		Begin and End addresses of the area used by the
 		simple memory test.
 
-- CONFIG_SYS_ALT_MEMTEST:
-		Enable an alternate, more extensive memory test.
-
 - CONFIG_SYS_MEMTEST_SCRATCH:
 		Scratch address used by the alternate memory test
 		You only need to set this if address zero isn't writeable
@@ -3430,9 +3394,6 @@ Low Level (hardware related) configuration options:
 		If defined, the x86 reset vector code is included. This is not
 		needed when U-Boot is running from Coreboot.
 
-- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
-		Enables the RTC32K OSC on AM33xx based plattforms
-
 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
 		Option to disable subpage write in NAND driver
 		driver that uses this: