X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=ed79298fd4ea9f09911ac5bbc7860da870d9055a;hb=bc8cb152d8fbea100023917c285129a6d9ccc3ba;hp=cce59ad7c05e23c8f95d989a9f3e41b9ea6ef048;hpb=d021e942107a1f7304a879cec99286ca462f7be3;p=u-boot

diff --git a/README b/README
index cce59ad7c0..ed79298fd4 100644
--- a/README
+++ b/README
@@ -713,17 +713,6 @@ The following options need to be configured:
 		as a convenience, when switching between booting from
 		RAM and NFS.
 
-- Bootcount:
-		CONFIG_BOOTCOUNT_ENV
-		If no softreset save registers are found on the hardware
-		"bootcount" is stored in the environment. To prevent a
-		saveenv on all reboots, the environment variable
-		"upgrade_available" is used. If "upgrade_available" is
-		0, "bootcount" is always 0, if "upgrade_available" is
-		1 "bootcount" is incremented in the environment.
-		So the Userspace Applikation must set the "upgrade_available"
-		and "bootcount" variable to 0, if a boot was successfully.
-
 - Pre-Boot Commands:
 		CONFIG_PREBOOT
 
@@ -1431,10 +1420,6 @@ The following options need to be configured:
 		be at least 4MB.
 
 - MII/PHY support:
-		CONFIG_PHY_ADDR
-
-		The address of PHY on MII bus.
-
 		CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
 		The clock frequency of the MII bus
@@ -2278,27 +2263,6 @@ The following options need to be configured:
 		A better solution is to properly configure the firewall,
 		but sometimes that is not allowed.
 
-- bootcount support:
-		CONFIG_AT91SAM9XE
-		enable special bootcounter support on at91sam9xe based boards.
-		CONFIG_SOC_DA8XX
-		enable special bootcounter support on da850 based boards.
-		CONFIG_BOOTCOUNT_RAM
-		enable support for the bootcounter in RAM
-		CONFIG_BOOTCOUNT_I2C
-		enable support for the bootcounter on an i2c (like RTC) device.
-			CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
-			CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
-						    the bootcounter.
-			CONFIG_BOOTCOUNT_ALEN = address len
-		CONFIG_BOOTCOUNT_EXT
-		enable support for the bootcounter in EXT filesystem
-			CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
-                                                    and write.
-			CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
-			CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
-			CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
-
 - Show boot progress:
 		CONFIG_SHOW_BOOT_PROGRESS
 
@@ -2518,12 +2482,6 @@ FIT uImage format:
 		kernel. Needed for UBI support.
 
 - UBI support
-		CONFIG_UBI_SILENCE_MSG
-
-		Make the verbose messages from UBI stop printing.  This leaves
-		warnings and errors enabled.
-
-
 		CONFIG_MTD_UBI_WL_THRESHOLD
 		This parameter defines the maximum difference between the highest
 		erase counter value and the lowest erase counter value of eraseblocks
@@ -2585,12 +2543,6 @@ FIT uImage format:
 		Enable UBI fastmap debug
 		default: 0
 
-- UBIFS support
-		CONFIG_UBIFS_SILENCE_MSG
-
-		Make the verbose messages from UBIFS stop printing.  This leaves
-		warnings and errors enabled.
-
 - SPL framework
 		CONFIG_SPL
 		Enable building of SPL globally.