X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=README;h=feb51ab94ce2b0aa6fc870229ffab9bdfcf332ee;hb=f1371048ab4dfaa0f7f26c0a60360548f1d752e3;hp=81692c0a49fedd8444663ec331383916591582f2;hpb=679ec154620eaf377143ba429124abc91abed0eb;p=u-boot diff --git a/README b/README index 81692c0a49..feb51ab94c 100644 --- a/README +++ b/README @@ -143,9 +143,9 @@ Directory Hierarchy: /cpu CPU specific files /arm720t Files specific to ARM 720 CPUs /arm920t Files specific to ARM 920 CPUs - /at91rm9200 Files specific to Atmel AT91RM9200 CPU - /imx Files specific to Freescale MC9328 i.MX CPUs - /s3c24x0 Files specific to Samsung S3C24X0 CPUs + /at91rm9200 Files specific to Atmel AT91RM9200 CPU + /imx Files specific to Freescale MC9328 i.MX CPUs + /s3c24x0 Files specific to Samsung S3C24X0 CPUs /arm925t Files specific to ARM 925 CPUs /arm926ejs Files specific to ARM 926 CPUs /arm1136 Files specific to ARM 1136 CPUs @@ -177,9 +177,6 @@ Directory Hierarchy: /mips Files generic to MIPS architecture /cpu CPU specific files /lib Architecture specific library files - /nios Files generic to Altera NIOS architecture - /cpu CPU specific files - /lib Architecture specific library files /nios2 Files generic to Altera NIOS2 architecture /cpu CPU specific files /lib Architecture specific library files @@ -535,25 +532,6 @@ The following options need to be configured: must be defined, to setup the maximum idle timeout for the SMC. -- Interrupt driven serial port input: - CONFIG_SERIAL_SOFTWARE_FIFO - - PPC405GP only. - Use an interrupt handler for receiving data on the - serial port. It also enables using hardware handshake - (RTS/CTS) and UART's built-in FIFO. Set the number of - bytes the interrupt driven input buffer should have. - - Leave undefined to disable this feature, including - disable the buffer and hardware handshake. - -- Console UART Number: - CONFIG_UART1_CONSOLE - - AMCC PPC4xx only. - If defined internal UART1 (and not UART0) is used - as default U-Boot console. - - Boot Delay: CONFIG_BOOTDELAY - in seconds Delay before automatically booting the default image; set to -1 to disable autoboot. @@ -1498,6 +1476,16 @@ The following options need to be configured: #define I2C_DELAY udelay(2) + CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA + + If your arch supports the generic GPIO framework (asm/gpio.h), + then you may alternatively define the two GPIOs that are to be + used as SCL / SDA. Any of the previous I2C_xxx macros will + have GPIO-based defaults assigned to them as appropriate. + + You should define these to the GPIO value as given directly to + the generic GPIO functions. + CONFIG_SYS_I2C_INIT_BOARD When a board is reset during an i2c bus transfer @@ -2357,6 +2345,14 @@ Configuration Settings: on high Ethernet traffic. Defaults to 4 if not defined. +- CONFIG_ENV_MAX_ENTRIES + + Maximum number of entries in the hash table that is used + internally to store the environment settings. The default + setting is supposed to be generous and should work in most + cases. This setting can be used to tune behaviour; see + lib/hashtable.c for details. + The following definitions that deal with the placement and management of environment data (variable area); in general, we support the following configurations: @@ -2507,7 +2503,7 @@ to save the current settings. I2C muxes, you can define here, how to reach this EEPROM. For example: - #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0" + #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0" EEPROM which holds the environment, is reached over a pca9547 i2c mux with address 0x70, channel 3. @@ -2565,7 +2561,7 @@ to save the current settings. Please note that the environment is read-only until the monitor has been relocated to RAM and a RAM copy of the environment has been -created; also, when using EEPROM you will have to use getenv_r() +created; also, when using EEPROM you will have to use getenv_f() until then to read environment variables. The environment is protected by a CRC32 checksum. Before the monitor @@ -3151,10 +3147,10 @@ List of environment variables (most likely not complete): interface is currently active. For example you can do the following - => setenv ethact FEC ETHERNET - => ping 192.168.0.1 # traffic sent on FEC ETHERNET - => setenv ethact SCC ETHERNET - => ping 10.0.0.1 # traffic sent on SCC ETHERNET + => setenv ethact FEC + => ping 192.168.0.1 # traffic sent on FEC + => setenv ethact SCC + => ping 10.0.0.1 # traffic sent on SCC ethrotate - When set to "no" U-Boot does not go through all available network interfaces. @@ -3337,8 +3333,8 @@ details; basically, the header defines the following image properties: Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS, INTEGRITY). * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86, - IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit; - Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC). + IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit; + Currently supported: ARM, AVR32, Intel x86, MIPS, Nios II, PowerPC). * Compression Type (uncompressed, gzip, bzip2) * Load Address * Entry Point @@ -4023,6 +4019,14 @@ On ARM, the following registers are used: ==> U-Boot will use R8 to hold a pointer to the global data +On Nios II, the ABI is documented here: + http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf + + ==> U-Boot will use gp to hold a pointer to the global data + + Note: on Nios II, we give "-G0" option to gcc and don't use gp + to access small data sections, so gp is free. + NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope, or current versions of GCC may "optimize" the code too much.