X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=board%2Fpcs440ep%2Fpcs440ep.c;h=5a3ec584451bbd502cdce86a69f50a3bf95e8f58;hb=711a6722f97d21404d04c7a36ccfdc6e2b442229;hp=f966d02f1070db05362ef2e7edd22f22e99f0984;hpb=084f3ddac6ab624a4b1c7174b3cdf9cc25866217;p=u-boot diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c index f966d02f10..5a3ec58445 100644 --- a/board/pcs440ep/pcs440ep.c +++ b/board/pcs440ep/pcs440ep.c @@ -22,7 +22,7 @@ */ #include -#include +#include #include #include #include @@ -148,28 +148,28 @@ int board_early_init_f(void) mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */ /*-------------------------------------------------------------------- - * GPIO's are alreay setup in cpu/ppc4xx/cpu_init.c + * GPIO's are alreay setup in arch/powerpc/cpu/ppc4xx/cpu_init.c * via define from board config file. *-------------------------------------------------------------------*/ /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ - mtdcr(uic0sr, 0xffffffff); /* clear all */ - mtdcr(uic0er, 0x00000000); /* disable all */ - mtdcr(uic0cr, 0x00000001); /* UIC1 crit is critical */ - mtdcr(uic0pr, 0xfffffe1f); /* per ref-board manual */ - mtdcr(uic0tr, 0x01c00000); /* per ref-board manual */ - mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr(uic0sr, 0xffffffff); /* clear all */ - - mtdcr(uic1sr, 0xffffffff); /* clear all */ - mtdcr(uic1er, 0x00000000); /* disable all */ - mtdcr(uic1cr, 0x00000000); /* all non-critical */ - mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */ - mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */ - mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(UIC0SR, 0xffffffff); /* clear all */ + mtdcr(UIC0ER, 0x00000000); /* disable all */ + mtdcr(UIC0CR, 0x00000001); /* UIC1 crit is critical */ + mtdcr(UIC0PR, 0xfffffe1f); /* per ref-board manual */ + mtdcr(UIC0TR, 0x01c00000); /* per ref-board manual */ + mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC0SR, 0xffffffff); /* clear all */ + + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + mtdcr(UIC1ER, 0x00000000); /* disable all */ + mtdcr(UIC1CR, 0x00000000); /* all non-critical */ + mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */ + mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */ + mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC1SR, 0xffffffff); /* clear all */ /*-------------------------------------------------------------------- * Setup other serial configuration @@ -509,12 +509,13 @@ int misc_init_r (void) int checkboard(void) { - char *s = getenv("serial#"); + char buf[64]; + int i = getenv_f("serial#", buf, sizeof(buf)); printf("Board: PCS440EP"); - if (s != NULL) { + if (i > 0) { puts(", serial# "); - puts(s); + puts(buf); } putc('\n'); @@ -550,166 +551,6 @@ phys_size_t initdram (int board_type) return dram_size; } -/************************************************************************* - * pci_pre_init - * - * This routine is called just prior to registering the hose and gives - * the board the opportunity to check things. Returning a value of zero - * indicates that things are bad & PCI initialization should be aborted. - * - * Different boards may wish to customize the pci controller structure - * (add regions, override default access routines, etc) or perform - * certain pre-initialization actions. - * - ************************************************************************/ -#if defined(CONFIG_PCI) -int pci_pre_init(struct pci_controller *hose) -{ - unsigned long addr; - - /*-------------------------------------------------------------------------+ - | Set priority for all PLB3 devices to 0. - | Set PLB3 arbiter to fair mode. - +-------------------------------------------------------------------------*/ - mfsdr(SD0_AMP1, addr); - mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00); - addr = mfdcr(PLB3_ACR); - mtdcr(PLB3_ACR, addr | 0x80000000); - - /*-------------------------------------------------------------------------+ - | Set priority for all PLB4 devices to 0. - +-------------------------------------------------------------------------*/ - mfsdr(SD0_AMP0, addr); - mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00); - addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */ - mtdcr(PLB4_ACR, addr); - - /*-------------------------------------------------------------------------+ - | Set Nebula PLB4 arbiter to fair mode. - +-------------------------------------------------------------------------*/ - /* Segment0 */ - addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR; - addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED; - addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP; - addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP; - mtdcr(PLB0_ACR, addr); - - /* Segment1 */ - addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR; - addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED; - addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP; - addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP; - mtdcr(PLB1_ACR, addr); - - return 1; -} -#endif /* defined(CONFIG_PCI) */ - -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /*--------------------------------------------------------------------------+ - * Set up Direct MMIO registers - *--------------------------------------------------------------------------*/ - /*--------------------------------------------------------------------------+ - | PowerPC440 EP PCI Master configuration. - | Map one 1Gig range of PLB/processor addresses to PCI memory space. - | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF - | Use byte reversed out routines to handle endianess. - | Make this region non-prefetchable. - +--------------------------------------------------------------------------*/ - out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */ - out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */ - out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ - out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */ - out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */ - out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ - out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */ - - out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ - out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */ - out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */ - out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */ - - /*--------------------------------------------------------------------------+ - * Set up Configuration registers - *--------------------------------------------------------------------------*/ - - /* Program the board's subsystem id/vendor id */ - pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, - CONFIG_SYS_PCI_SUBSYS_VENDORID); - pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID); - - /* Configure command register as bus master */ - pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); - - /* 240nS PCI clock */ - pci_write_config_word(0, PCI_LATENCY_TIMER, 1); - - /* No error reporting */ - pci_write_config_word(0, PCI_ERREN, 0); - - pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); - -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - -/************************************************************************* - * pci_master_init - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) -void pci_master_init(struct pci_controller *hose) -{ - unsigned short temp_short; - - /*--------------------------------------------------------------------------+ - | Write the PowerPC440 EP PCI Configuration regs. - | Enable PowerPC440 EP to be a master on the PCI bus (PMM). - | Enable PowerPC440 EP to act as a PCI memory target (PTM). - +--------------------------------------------------------------------------*/ - pci_read_config_word(0, PCI_COMMAND, &temp_short); - pci_write_config_word(0, PCI_COMMAND, - temp_short | PCI_COMMAND_MASTER | - PCI_COMMAND_MEMORY); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */ - -/************************************************************************* - * is_pci_host - * - * This routine is called to determine if a pci scan should be - * performed. With various hardware environments (especially cPCI and - * PPMC) it's insufficient to depend on the state of the arbiter enable - * bit in the strap register, or generic host/adapter assumptions. - * - * Rather than hard-code a bad assumption in the general 440 code, the - * 440 pci code requires the board to decide at runtime. - * - * Return 0 for adapter mode, non-zero for host (monarch) mode. - * - * - ************************************************************************/ -#if defined(CONFIG_PCI) -int is_pci_host(struct pci_controller *hose) -{ - /* PCS440EP is always configured as host. */ - return (1); -} -#endif /* defined(CONFIG_PCI) */ - /************************************************************************* * hw_watchdog_reset * @@ -727,7 +568,7 @@ void hw_watchdog_reset(void) * "led" Commando for the U-Boot shell * ************************************************************************/ -int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { int rcode = 0, i; ulong pattern = 0; @@ -771,14 +612,13 @@ U_BOOT_CMD( * "sha1" Commando for the U-Boot shell * ************************************************************************/ -int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { int rcode = -1; if (argc < 2) { - usage: - cmd_usage(cmdtp); - return 1; +usage: + return cmd_usage(cmdtp); } if (argc >= 3) {