X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=common%2Fspl%2FKconfig;h=e1b91f5d895c30a55642a6cddf2ef5520e081d23;hb=af2f44267;hp=582b685dad36b9cea6298481d49ceb214e8a5926;hpb=ceff355a5f3038ddb49618d9adc716b0ed978aea;p=u-boot

diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 582b685dad..e1b91f5d89 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -94,6 +94,7 @@ config SPL_STACK_R
 config SPL_STACK_R_ADDR
 	depends on SPL_STACK_R
 	hex "SDRAM location for SPL stack"
+	default 0x82000000 if ARCH_OMAP2PLUS
 	help
 	  Specify the address in SDRAM for the SPL stack. This will be set up
 	  before board_init_r() is called.
@@ -141,11 +142,12 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
 	default 0x50 if ARCH_SUNXI
 	default 0x75 if ARCH_DAVINCI
 	default 0x8a if ARCH_MX6
-	default 0x100 if ARCH_ROCKCHIP || ARCH_UNIPHIER
+	default 0x100 if ARCH_UNIPHIER
 	default 0x140 if ARCH_MVEBU
 	default 0x200 if ARCH_SOCFPGA || ARCH_AT91
 	default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \
 		         OMAP54XX || AM33XX || AM43XX
+	default 0x4000 if ARCH_ROCKCHIP
 	help
 	  Address on the MMC to load U-Boot from, when the MMC is being used
 	  in raw mode. Units: MMC sectors (1 sector = 512 bytes).
@@ -226,6 +228,21 @@ config SPL_SHA256_SUPPORT
 	  SHA256 variant is supported: SHA512 and others are not currently
 	  supported in U-Boot.
 
+config SPL_FIT_IMAGE_TINY
+	bool "Remove functionality from SPL FIT loading to reduce size"
+	depends on SPL_FIT
+	default y if MACH_SUN50I || MACH_SUN50I_H5
+	help
+	  Enable this to reduce the size of the FIT image loading code
+	  in SPL, if space for the SPL binary is very tight.
+
+	  This removes the detection of image types (which forces the
+	  first image to be treated as having a U-Boot style calling
+	  convention) and skips the recording of each loaded payload
+	  (i.e. loadable) into the FDT (modifying the loaded FDT to
+	  ensure this information is available to the next image
+	  invoked).
+
 config SPL_CPU_SUPPORT
 	bool "Support CPU drivers"
 	help
@@ -284,6 +301,7 @@ config SPL_ENV_SUPPORT
 config SPL_SAVEENV
 	bool "Support save environment"
 	depends on SPL_ENV_SUPPORT
+	select SPL_MMC_WRITE if ENV_IS_IN_MMC
 	help
 	  Enable save environment support in SPL after setenv. By default
 	  the saveenv option is not provided in SPL, but some boards need
@@ -398,6 +416,14 @@ config SPL_MMC_SUPPORT
 	  this option to build the drivers in drivers/mmc as part of an SPL
 	  build.
 
+config SPL_MMC_WRITE
+	bool "MMC/SD/SDIO card support for write operations in SPL"
+	depends on SPL_MMC_SUPPORT
+	default n
+	help
+	  Enable write access to MMC and SD Cards in SPL
+
+
 config SPL_MPC8XXX_INIT_DDR_SUPPORT
 	bool "Support MPC8XXX DDR init"
 	help
@@ -603,6 +629,14 @@ config SPL_SPI_SUPPORT
 	  enable SPI drivers that are needed for other purposes also, such
 	  as a SPI PMIC.
 
+config SPL_THERMAL
+	bool "Driver support for thermal devices"
+	help
+	  Enable support for temperature-sensing devices. Some SoCs have on-chip
+	  temperature sensors to permit warnings, speed throttling or even
+	  automatic power-off when the temperature gets too high or low. Other
+	  devices may be discrete but connected on a suitable bus.
+
 config SPL_USB_HOST_SUPPORT
 	bool "Support USB host drivers"
 	help
@@ -668,6 +702,12 @@ config SPL_DFU_RAM
 
 endchoice
 
+config SPL_USB_SDP_SUPPORT
+	bool "Support SDP (Serial Download Protocol)"
+	help
+	  Enable Serial Download Protocol (SDP) device support in SPL. This
+	  allows to download images into memory and execute (jump to) them
+	  using the same protocol as implemented by the i.MX family's boot ROM.
 endif
 
 config SPL_WATCHDOG_SUPPORT
@@ -686,19 +726,27 @@ config SPL_YMODEM_SUPPORT
 	  means of transmitting U-Boot over a serial line for using in SPL,
 	  with a checksum to ensure correctness.
 
-config SPL_ATF_SUPPORT
+config SPL_ATF
 	bool "Support ARM Trusted Firmware"
 	depends on ARM64
 	help
-	  ATF(ARM Trusted Firmware) is a component for ARM arch64 which which
-	  is loaded by SPL(which is considered as BL2 in ATF terminology).
+	  ATF(ARM Trusted Firmware) is a component for ARM AArch64 which
+	  is loaded by SPL (which is considered as BL2 in ATF terminology).
 	  More detail at: https://github.com/ARM-software/arm-trusted-firmware
 
-config SPL_ATF_TEXT_BASE
-	depends on SPL_ATF_SUPPORT
-	hex "ATF BL31 base address"
+config SPL_ATF_NO_PLATFORM_PARAM
+        bool "Pass no platform parameter"
+	depends on SPL_ATF
 	help
-	  This is the base address in memory for ATF BL31 text and entry point.
+	  While we expect to call a pointer to a valid FDT (or NULL)
+	  as the platform parameter to an ATF, some ATF versions are
+	  not U-Boot aware and have an insufficiently robust parameter
+	  validation to gracefully reject a FDT being passed.
+
+	  If this option is enabled, the spl_atf os-type handler will
+	  always pass NULL for the platform parameter.
+
+	  If your ATF is affected, say Y.
 
 config TPL
 	bool
@@ -709,6 +757,13 @@ config TPL
 
 if TPL
 
+config TPL_BOARD_INIT
+	bool "Call board-specific initialization in TPL"
+	help
+	  If this option is enabled, U-Boot will call the function
+	  spl_board_init() from board_init_r(). This function should be
+	  provided by the board.
+
 config TPL_LDSCRIPT
         string "Linker script for the TPL stage"
 	depends on TPL