X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=doc%2FREADME.mpc8360emds;h=d65a2a48a9d60baea3e0db82062f029530734b3c;hb=678150f155f0cc69ce7868f53d91e3ab2859510b;hp=c87469f43d10db14e7c43c2b3d5fc1943352265e;hpb=dd520bf314c7add4183c5191692180f576f96b60;p=u-boot

diff --git a/doc/README.mpc8360emds b/doc/README.mpc8360emds
index c87469f43d..d65a2a48a9 100644
--- a/doc/README.mpc8360emds
+++ b/doc/README.mpc8360emds
@@ -1,7 +1,7 @@
 Freescale MPC8360EMDS Board
 -----------------------------------------
 1.	Board Switches and Jumpers
-1.0 	There are four Dual-In-Line Packages(DIP) Switches on MPC8360EMDS board
+1.0	There are four Dual-In-Line Packages(DIP) Switches on MPC8360EMDS board
 	For some reason, the HW designers describe the switch settings
 	in terms of 0 and 1, and then map that to physical switches where
 	the label "On" refers to logic 0 and "Off" is logic 1.
@@ -21,7 +21,13 @@ Freescale MPC8360EMDS Board
 	SW3[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On"
 		and bits labeled 8 is set as "Off".
 
-1.1	For the MPC8360E PB PROTO Board
+1.1	There are three type boards for MPC8360E silicon up to now, They are
+
+	* MPC8360E-MDS-PB PROTO (a.k.a 8360SYS PROTOTYPE)
+	* MPC8360E-MDS-PB PILOT (a.k.a 8360SYS PILOT)
+	* MPC8360EA-MDS-PB PROTO (a.k.a 8360SYS2 PROTOTYPE)
+
+1.2	For all the MPC8360EMDS Board
 
 	First, make sure the board default setting is consistent with the
 	document shipped with your board. Then apply the following setting:
@@ -33,6 +39,21 @@ Freescale MPC8360EMDS Board
 	JP6 1-2
 	on board Oscillator: 66M
 
+1.3	Since different board/chip rev. combinations have AC timing issues,
+	u-boot forces RGMII-ID (RGMII with Internal Delay) mode on by default
+	by the patch (mpc83xx: Disable G1TXCLK, G2TXCLK h/w buffers).
+
+	When the rev2.x silicon mount on these boards, and if you are using
+	u-boot version after this patch, to make the ethernet interfaces usable,
+	and to enable RGMII-ID on your board, you have to setup the jumpers
+	correctly.
+
+	* MPC8360E-MDS-PB PROTO
+	  nothing to do
+	* MPC8360E-MDS-PB PILOT
+	  JP9 and JP8 should be ON
+	* MPC8360EA-MDS-PB PROTO
+	  JP2 and JP3 should be ON
 
 2.	Memory Map
 
@@ -60,7 +81,7 @@ Freescale MPC8360EMDS Board
 
 	include/configs/MPC8360EMDS.h
 
-    CONFIG_MPC83XX	    MPC83xx family for both MPC8349 and MPC8360
+    CONFIG_MPC83xx	    MPC83xx family for both MPC8349 and MPC8360
     CONFIG_MPC8360	    MPC8360 specific
     CONFIG_MPC8360EMDS	    MPC8360EMDS board specific