X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=doc%2FREADME.rockchip;h=597f068aca68af9cc9e7aac5c85c599327328950;hb=451dcf5cd002ee0e107989f849f9b4f56570f809;hp=2d8cf9fae02ea98d54ffd883e06ac65d61092c20;hpb=7da8680b260b4598d841d9a8432d95d56cb86d9f;p=u-boot

diff --git a/doc/README.rockchip b/doc/README.rockchip
index 2d8cf9fae0..597f068aca 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -36,13 +36,14 @@ You will need:
 Building
 ========
 
-At present eight RK3288 boards are supported:
+At present nine RK3288 boards are supported:
 
    - EVB RK3288 - use evb-rk3288 configuration
    - Fennec RK3288 - use fennec-rk3288 configuration
    - Firefly RK3288 - use firefly-rk3288 configuration
    - Hisense Chromebook - use chromebook_jerry configuration
    - MiQi RK3288 - use miqi-rk3288 configuration
+   - phyCORE-RK3288 RDK - use phycore-rk3288 configuration
    - PopMetal RK3288 - use popmetal-rk3288 configuration
    - Radxa Rock 2 - use rock2 configuration
    - Tinker RK3288 - use tinker-rk3288 configuration
@@ -98,13 +99,13 @@ To write an image that boots from an SD card (assumed to be /dev/sdc):
    ./firefly-rk3288/tools/mkimage -n rk3288 -T rksd -d \
 	firefly-rk3288/spl/u-boot-spl-dtb.bin out && \
    sudo dd if=out of=/dev/sdc seek=64 && \
-   sudo dd if=firefly-rk3288/u-boot-dtb.img of=/dev/sdc seek=256
+   sudo dd if=firefly-rk3288/u-boot-dtb.img of=/dev/sdc seek=16384
 
 This puts the Rockchip header and SPL image first and then places the U-Boot
-image at block 256 (i.e. 128KB from the start of the SD card). This
+image at block 16384 (i.e. 8MB from the start of the SD card). This
 corresponds with this setting in U-Boot:
 
-   #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	256
+   #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x4000
 
 Put this SD (or micro-SD) card into your board and reset it. You should see
 something like:
@@ -129,7 +130,7 @@ load a second-level bootloader(ie. U-BOOT) as soon as it returns to bootrom.
 Therefore RK3288 has another loading sequence like RK3036. The option of
 U-Boot is controlled with this setting in U-Boot:
 
-	#define CONFIG_ROCKCHIP_SPL_BACK_TO_BROM
+	#define CONFIG_SPL_ROCKCHIP_BACK_TO_BROM
 
 You can create the image via the following operations:
 
@@ -149,6 +150,24 @@ Note: rk3036 SDMMC and debug uart use the same iomux, so if you boot from SD, th
       debug uart must be disabled
 
 
+Booting from an SD card on RK3288 with TPL
+==========================================
+
+Since the size of SPL can't be exceeded 0x8000 bytes in RK3288, it is not possible add
+new SPL features like Falcon mode or etc.
+
+So introduce TPL so-that adding new features to SPL is possible because now TPL should
+run minimal with code like DDR, clock etc and rest of new features in SPL.
+
+As of now TPL is added on Vyasa-RK3288 board.
+
+To write an image that boots from an SD card (assumed to be /dev/mmcblk0):
+
+   ./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out &&
+    cat ./spl/u-boot-spl-dtb.bin >> out &&
+    sudo dd if=out of=/dev/mmcblk0 seek=64 &&
+    sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 seek=16384
+
 Booting from an SD card on RK3188
 =================================
 
@@ -157,17 +176,17 @@ described above, but the image creation needs a bit more care.
 
 The bootrom of rk3188 expects to find a small 1kb loader which returns
 control to the bootrom, after which it will load the real loader, which
-can then be up to 29kb in size and does the regular ddr init.
+can then be up to 29kb in size and does the regular ddr init.  This is
+handled by a single image (built as the SPL stage) that tests whether
+it is handled for the first or second time via code executed from the
+boot0-hook.
 
 Additionally the rk3188 requires everything the bootrom loads to be
 rc4-encrypted. Except for the very first stage the bootrom always reads
 and decodes 2kb pages, so files should be sized accordingly.
 
 # copy tpl, pad to 1020 bytes and append spl
-cat tpl/u-boot-tpl.bin > tplspl.bin
-truncate -s 1020 tplspl.bin
-cat spl/u-boot-spl.bin >> tplspl.bin
-tools/mkimage -n rk3188 -T rksd -d tplspl.bin out
+tools/mkimage -n rk3188 -T rksd -d spl/u-boot-spl.bin out
 
 # truncate, encode and append u-boot.bin
 truncate -s %2048 u-boot.bin