X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FG2000.h;h=08ba8404bf8c88efc639edec913c83bc669db71b;hb=d9354530fe3a891718e3a9b88a756545c3891475;hp=d2883eb8d74cb1525d007150b8de23794ed8bfa2;hpb=83653121d7382fccfe329cb732f77f116341ef1d;p=u-boot diff --git a/include/configs/G2000.h b/include/configs/G2000.h index d2883eb8d7..08ba8404bf 100644 --- a/include/configs/G2000.h +++ b/include/configs/G2000.h @@ -37,6 +37,8 @@ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_G2000 1 /* ...on a PLU405 board */ +#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ @@ -78,7 +80,6 @@ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ @@ -129,9 +130,6 @@ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#endif #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ @@ -151,9 +149,14 @@ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 -#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ @@ -347,10 +350,9 @@ #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- @@ -367,22 +369,14 @@ * * following GPIO setting changed for G20000, 080304 */ -#define CONFIG_SYS_GPIO0_OSRH 0x40005555 -#define CONFIG_SYS_GPIO0_OSRL 0x40000110 -#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 -#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_OSRL 0x40005555 +#define CONFIG_SYS_GPIO0_OSRH 0x40000110 +#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - /* * Default speed selection (cpu_plb_opb_ebc) in mhz. * This value will be set if iic boot eprom is disabled.