X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FHUB405.h;h=0727606bbb87bc776dec10717363950537b1694e;hb=741a6d010d09b5bafca8e4cdfb6b2f8a2c07994d;hp=0fa52991876d7efe5277941a2e769383d7bf2fda;hpb=47b1e3d77fcd951df45259a4b20cc116d226e10f;p=u-boot

diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index 0fa5299187..0727606bbb 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -60,18 +60,30 @@
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_NAND	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -88,7 +100,7 @@
 #define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -135,36 +147,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -238,9 +232,9 @@
 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
-#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
+#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
@@ -263,16 +257,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Init Memory Controller:
  *