X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FJSE.h;h=8aca1f941db11f105e06ce4e446ee34d0a4390b3;hb=6b7243aa89cdacefe46963dbe11cee0cbf021a49;hp=ecc344d8296e083676a91c2181cec1c233ab57e3;hpb=93f6d72544da4510a146bc4c93d609b0116cde37;p=u-boot diff --git a/include/configs/JSE.h b/include/configs/JSE.h index ecc344d829..8aca1f941d 100644 --- a/include/configs/JSE.h +++ b/include/configs/JSE.h @@ -41,28 +41,28 @@ /* ... with a 33MHz OSC. connected to the SysCLK input */ #define CONFIG_SYS_CLK_FREQ 33333333 /* ... with on-chip memory here (4KBytes) */ -#define CFG_OCM_DATA_ADDR 0xF4000000 -#define CFG_OCM_DATA_SIZE 0x00001000 +#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000 /* Do not set up locked dcache as init ram. */ -#undef CFG_INIT_DCACHE_CS +#undef CONFIG_SYS_INIT_DCACHE_CS /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */ #define CONFIG_SYSTEMACE 1 -#define CFG_SYSTEMACE_BASE 0xf0000000 -#define CFG_SYSTEMACE_WIDTH 8 +#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000 +#define CONFIG_SYS_SYSTEMACE_WIDTH 8 #define CONFIG_DOS_PARTITION 1 /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */ -#define CFG_TEMP_STACK_OCM 1 +#define CONFIG_SYS_TEMP_STACK_OCM 1 /* ... place INIT RAM in the OCM address */ -# define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR +# define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* ... give it the whole init ram */ -# define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE +# define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* ... Shave a bit off the end for global data */ -# define CFG_GBL_DATA_SIZE 128 -# define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +# define CONFIG_SYS_GBL_DATA_SIZE 128 +# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* ... and place the stack pointer at the top of what's left. */ -# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* Enable board_pre_init function */ #define CONFIG_BOARD_PRE_INIT 1 @@ -72,28 +72,28 @@ /* Disable call to post_init_f: late init function. */ #undef CONFIG_POST /* Enable DRAM test. */ -#define CFG_DRAM_TEST 1 +#define CONFIG_SYS_DRAM_TEST 1 /* Enable misc_init_r function. */ #define CONFIG_MISC_INIT_R 1 /* JSE has EEPROM chips that are good for environment. */ #undef CONFIG_ENV_IS_IN_NVRAM -#undef CFG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_IS_IN_EEPROM 1 #undef CONFIG_ENV_IS_NOWHERE /* This is the 7bit address of the device, not including P. */ -#define CFG_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* After the device address, need one more address byte. */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* The EEPROM is 512 bytes. */ -#define CFG_EEPROM_SIZE 512 +#define CONFIG_SYS_EEPROM_SIZE 512 /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CFG_EEPROM_PAGE_WRITE_BITS 4 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* Put the environment in the second half. */ -#define CFG_ENV_OFFSET 0x00 -#define CFG_ENV_SIZE 512 +#define CONFIG_ENV_OFFSET 0x00 +#define CONFIG_ENV_SIZE 512 /* The JSE connects UART1 to the console tap connector. */ @@ -130,8 +130,9 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ @@ -171,52 +172,52 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_HUSH_PARSER /* use "hush" command parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ /* - * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CFG_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. + * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. * The Linux BASE_BAUD define should match this configuration. * baseBaud = cpuClock/(uartDivisor*16) - * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, + * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CFG_BASE_BAUD 691200 +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 691200 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /*----------------------------------------------------------------------- @@ -232,14 +233,14 @@ #undef CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ -#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ -#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * External peripheral base address @@ -248,36 +249,36 @@ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CFG_KEY_REG_BASE_ADDR 0xF0100000 -#define CFG_IR_REG_BASE_ADDR 0xF0200000 -#define CFG_FPGA_REG_BASE_ADDR 0xF0300000 +#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 +#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFF80000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* * Init Memory Controller: @@ -285,7 +286,7 @@ * BR0/1 and OR0/1 (FLASH) */ -#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ +#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */