X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8560ADS.h;h=218d77d1bd8e7e0fec1637d7f71f9802c1ee3c91;hb=d26e34c4c4b6473fdbd412a3b2dc33a94b08e8ff;hp=e1bc8ccd3253e65ae8671d73a4cccb5e5655f947;hpb=a69fdc7787bfa2f27eed74c2ee58c28ce932d502;p=u-boot

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index e1bc8ccd32..218d77d1bd 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -18,15 +18,8 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
-
 /* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_CPM2		1	/* has CPM2 */
-#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific */
-#define CONFIG_MPC8560		1
 
 /*
  * default CCARBAR is at 0xff700000
@@ -34,13 +27,11 @@
  */
 #define	CONFIG_SYS_TEXT_BASE	0xfff80000
 
-#define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 #define CONFIG_RESET_PHY_R	1	/* Call reset_phy() */
 
 /*
@@ -61,7 +52,6 @@
 #define CONFIG_SYS_CLK_FREQ	33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -77,7 +67,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -134,7 +123,6 @@
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -199,7 +187,6 @@
 #define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 
-
 /*
  * 32KB, 8-bit wide for ADS config reg
  */
@@ -227,16 +214,6 @@
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -267,9 +244,6 @@
 #define CONFIG_SYS_PCI1_IO_SIZE	0x100000	/* 1M */
 
 #if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -284,7 +258,6 @@
 
 #endif	/* CONFIG_PCI */
 
-
 #ifdef CONFIG_TSEC_ENET
 
 #ifndef CONFIG_MII
@@ -356,7 +329,6 @@
 
 #endif
 
-
 /*
  * Environment
  */
@@ -383,12 +355,9 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
@@ -397,7 +366,6 @@
 #endif
 
 #if defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
 #endif
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
@@ -432,7 +400,6 @@
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif
 
-
 /*
  * Environment Configuration
  */
@@ -455,7 +422,6 @@
 
 #define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE	115200