X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8569MDS.h;h=19d32718fab2d64761f64418288e5aee6b7d32c5;hb=cfeba45f505290ec719076dd174727d10045aa2b;hp=5f804254fd066648dcd41f98c86c7c47fa306e66;hpb=c39f44dc6f5ae843d5def511f6e71d4b012dc598;p=u-boot

diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
index 5f804254fd..19d32718fa 100644
--- a/include/configs/MPC8569MDS.h
+++ b/include/configs/MPC8569MDS.h
@@ -105,20 +105,11 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
-						/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR
-						/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT	CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif
 
 /* DDR Setup */
@@ -240,12 +231,12 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_NAND			1
 #define CONFIG_NAND_FSL_ELBC		1
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-#define CONFIG_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE_PHYS \
+#define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE_PHYS \
 				| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
 				| BR_PS_8	     /* Port Size = 8 bit */ \
 				| BR_MS_FCM	     /* MSEL = FCM */ \
 				| BR_V)		     /* valid */
-#define CONFIG_NAND_OR_PRELIM	(0xFFFC0000	     /* length 256K */ \
+#define CONFIG_SYS_NAND_OR_PRELIM	(0xFFFC0000	     /* length 256K */ \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
@@ -254,15 +245,15 @@ extern unsigned long get_clock_freq(void);
 				| OR_FCM_EHTR)
 
 #ifdef CONFIG_RAMBOOT_NAND
-#define CONFIG_SYS_BR0_PRELIM	CONFIG_NAND_BR_PRELIM	/* NAND Base Address */
-#define CONFIG_SYS_OR0_PRELIM	CONFIG_NAND_OR_PRELIM	/* NAND Options */
+#define CONFIG_SYS_BR0_PRELIM	CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR0_PRELIM	CONFIG_SYS_NAND_OR_PRELIM/* NAND Options */
 #define CONFIG_SYS_BR3_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
 #define CONFIG_SYS_OR3_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
 #else
 #define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
 #define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
-#define CONFIG_SYS_BR3_PRELIM	CONFIG_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR3_PRELIM	CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 #endif
 
 #define CONFIG_SYS_LBC_LCRR	0x00000004	/* LB clock ratio reg */
@@ -385,13 +376,13 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK12
 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16	/* CLK16 for RMII */
 #define CONFIG_SYS_UEC1_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       8	/* 0x8 for RMII */
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH1 */
@@ -406,13 +397,13 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK17
 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16	/* CLK 16 for RMII */
 #define CONFIG_SYS_UEC2_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       0x9	/* 0x9 for RMII */
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH2 */
@@ -427,13 +418,13 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC3_TX_CLK         QE_CLK12
 #define CONFIG_SYS_UEC3_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC3_PHY_ADDR       2
-#define CONFIG_SYS_UEC3_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC3_TX_CLK		QE_CLK16 /* CLK_16 for RMII */
 #define CONFIG_SYS_UEC3_ETH_TYPE	FAST_ETH
 #define CONFIG_SYS_UEC3_PHY_ADDR	0xA     /* 0xA for RMII */
-#define CONFIG_SYS_UEC3_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH3 */
@@ -448,13 +439,13 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC4_TX_CLK         QE_CLK17
 #define CONFIG_SYS_UEC4_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC4_PHY_ADDR       3
-#define CONFIG_SYS_UEC4_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC4_TX_CLK		QE_CLK16 /* CLK16 for RMII */
 #define CONFIG_SYS_UEC4_ETH_TYPE	FAST_ETH
 #define CONFIG_SYS_UEC4_PHY_ADDR	0xB     /* 0xB for RMII */
-#define CONFIG_SYS_UEC4_INTERFACE_TYPE RMII
+#define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH4 */
@@ -468,7 +459,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC6_TX_CLK         QE_CLK_NONE
 #define CONFIG_SYS_UEC6_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC6_PHY_ADDR       4
-#define CONFIG_SYS_UEC6_INTERFACE_TYPE SGMII
+#define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
 #endif /* CONFIG_UEC_ETH6 */
 
@@ -481,7 +472,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC8_TX_CLK         QE_CLK_NONE
 #define CONFIG_SYS_UEC8_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC8_PHY_ADDR       6
-#define CONFIG_SYS_UEC8_INTERFACE_TYPE SGMII
+#define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
 #endif /* CONFIG_UEC_ETH8 */
 
@@ -489,7 +480,6 @@ extern unsigned long get_clock_freq(void);
 
 #if defined(CONFIG_PCI)
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -500,10 +490,6 @@ extern unsigned long get_clock_freq(void);
 
 #endif	/* CONFIG_PCI */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI	1
-#endif
-
 /*
  * Environment
  */
@@ -590,11 +576,11 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ	(16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
@@ -605,8 +591,8 @@ extern unsigned long get_clock_freq(void);
  * Environment Configuration
  */
 #define CONFIG_HOSTNAME mpc8569mds
-#define CONFIG_ROOTPATH  /nfsroot
-#define CONFIG_BOOTFILE  your.uImage
+#define CONFIG_ROOTPATH  "/nfsroot"
+#define CONFIG_BOOTFILE  "your.uImage"
 
 #define CONFIG_SERVERIP  192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1