X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FSBC8540.h;h=93509ee087384bd7d7578b751da9efe93a9715c3;hb=ac53ee8318678190bf3c68da477a84a657d86fb0;hp=0451b208197006d8dd0f574d939f8268517c6f65;hpb=cbf9c117282b8729bdb86071997b58fcab58c444;p=u-boot

diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 0451b20819..93509ee087 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -48,7 +48,8 @@
 
 #define CONFIG_CPM2		1	/* has CPM2 */
 
-#define CONFIG_SBC8540      	1   	/* configuration for SBC8560 board */
+#define CONFIG_SBC8540		1	/* configuration for SBC8560 board */
+#define CONFIG_MPC8540		1
 
 #define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific (supplement)	*/
 
@@ -56,6 +57,7 @@
 #undef	CONFIG_PCI			/* pci ethernet support		*/
 #undef  CONFIG_ETHER_ON_FCC		/* cpm FCC ethernet support	*/
 
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
 #define CONFIG_ENV_OVERWRITE
 
@@ -98,20 +100,37 @@
 #else
   #define CFG_CCSRBAR		0xff700000	/* default CCSRBAR	*/
 #endif
+#define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	 */
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 #define CFG_SDRAM_SIZE		512		/* DDR is 512MB */
-#define SPD_EEPROM_ADDRESS	0x55		/*  DDR DIMM */
 
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
 #undef  CONFIG_DDR_ECC				/* only for ECC DDR module	*/
 #undef  CONFIG_SPD_EEPROM			/* Use SPD EEPROM for DDR setup */
+#undef  CONFIG_DDR_SPD
 
 #if defined(CONFIG_MPC85xx_REV1)
   #define CONFIG_DDR_DLL			/* possible DLL fix needed	*/
 #endif
 
+#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x55	/* CTLR 0 DIMM 0 */
+
 #undef CONFIG_CLOCKS_IN_MHZ
 
 #if defined(CONFIG_RAM_AS_FLASH)
@@ -214,12 +233,16 @@
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif
 
-/* I2C */
-#define	 CONFIG_HARD_I2C		/* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F
 #define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3000
 
 #define CFG_PCI_MEM_BASE	0xC0000000
 #define CFG_PCI_MEM_PHYS	0xC0000000
@@ -284,7 +307,7 @@
  */
 
 #define CFG_FLASH_CFI		1	/* Flash is CFI conformant		*/
-#define CFG_FLASH_CFI_DRIVER	1	/* Use the common driver		*/
+#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver		*/
 #if 0
 #define CFG_FLASH_USE_BUFFER_WRITE 1    /* use buffered writes (20x faster)     */
 #define CFG_FLASH_PROTECTION		/* use hardware protection		*/
@@ -334,28 +357,37 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				 ~(CFG_CMD_ENV | \
-				  CFG_CMD_LOADS ))
-  #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				~(CFG_CMD_ENV))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C)
-  #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C)
-  #endif
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+    #define CONFIG_CMD_MII
+#endif
+
+#if defined(CFG_RAMBOOT)
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -364,7 +396,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"SBC8540=> " /* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
   #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -382,13 +414,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
 
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE		32768
-#define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-  #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
 /*
  * Internal Definitions
  *
@@ -397,7 +422,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
   #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif