X-Git-Url: https://git.sur5r.net/?a=blobdiff_plain;f=include%2Fconfigs%2FTQM5200.h;h=19e0b1be1bdbb36badc288c1e61870f2bf811e48;hb=eb5ba3aefdf0f6cbd61684eeb61428f11fa7613c;hp=708eb7663852a80d1f33a0a7e21e7d7b4f601eb8;hpb=4f892924d238cc415891dbea336a0fdaff2f853b;p=u-boot

diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 708eb76638..19e0b1be1b 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -45,13 +45,11 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1			*/
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps			*/
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 #define CONFIG_BOOTCOUNT_LIMIT	1
 
 #ifdef CONFIG_FO300
 #define CONFIG_SYS_DEVICE_NULLDEV		1	/* enable null device */
-#define CONFIG_BOARD_EARLY_INIT_F	1	/* used to detect S1 switch position */
 #define CONFIG_USB_BIN_FIXUP		1	/* for a buggy USB device */
 #if 0
 #define FO300_SILENT_CONSOLE_WHEN_S1_CLOSED	1	/* silent console on PSC1 when S1 */
@@ -108,9 +106,6 @@
 #endif /* #ifndef CONFIG_TQM5200S */
 
 /* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
 
 /* USB */
 #if defined(CONFIG_CHARON) || defined(CONFIG_FO300) || \
@@ -129,8 +124,7 @@
 #ifndef CONFIG_CAM5200
 /* POST support */
 #define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
-				 CONFIG_SYS_POST_CPU	   | \
-				 CONFIG_SYS_POST_I2C)
+				 CONFIG_SYS_POST_CPU)
 #endif
 
 #ifdef CONFIG_POST
@@ -149,15 +143,8 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_BSP
-
-#ifdef CONFIG_VIDEO
-    #define CONFIG_CMD_BMP
-#endif
 
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
@@ -175,10 +162,6 @@
     #define CONFIG_CFG_FAT
 #endif
 
-#ifdef CONFIG_POST
-    #define CONFIG_CMD_DIAG
-#endif
-
 #define	CONFIG_TIMESTAMP		/* display image timestamps */
 
 #if (CONFIG_SYS_TEXT_BASE != 0xFFF00000)
@@ -293,54 +276,6 @@
 #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
 #endif
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-Boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
-
-/*
- * HW-Monitor configuration on Mini-FAP
- */
-#if defined (CONFIG_MINIFAP)
-#define CONFIG_SYS_I2C_HWMON_ADDR		0x2C
-#endif
-
-/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_MINIFAP)
-#undef CONFIG_SYS_POST_I2C_ADDRS
-#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_EEPROM_ADDR,	\
-					 CONFIG_SYS_I2C_HWMON_ADDR,	\
-					 CONFIG_SYS_I2C_SLAVE}
-#endif
-
 /*
  * Flash configuration
  */
@@ -559,18 +494,6 @@
 #endif
 #endif
 
-/*
- * RTC configuration
- */
-#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
-# define CONFIG_RTC_M41T11 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-# define CONFIG_SYS_M41T11_BASE_YEAR	1900    /* because Linux uses the same base
-					   year */
-#else
-# define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
-#endif
-
 /*
  * Miscellaneous configurable options
  */